EASTMAN E Series Manual de usuario
Eastman
Over a Century of Cutting Expertise
®
Form CR-50-0528
WARNING
Equipment Starts
automatically -
can cause severe
injury
KEEP AWAY
779 Washington St., Buffalo, N.Y. 14203-1396 U.S.A. • (716)856-2200 • Fax (716)856-1140 or (716)856-2068
Manufacturers of Eastman Cloth Cutting and Cloth Spreading Machines
Website: www.EastmanCuts.com
THE EASTMAN ®
Cradle Spreading Machine
E-Series
Technical Support:
1-800-872-5595
Quick Start Guide
This machine is equipped with drive belts and
roller tubes moving at high rates of speed.
Keep hands, arms, and loose objects away
from drive belts and rollers at all times.
Misuse of this machine or failure to follow all
safety instructions on this machine and in the
instruction manual may result in serious per-
sonal injuries.
WARNING
10
1
Turn Main Power "ON"
Note: Switching the main
power on will activate the
monitor and software.
2In the "Table Length Menu" set "Load
End" by pressing the "Find Load End"
or "Teach Load End" buttons. 3
Set "Table End" by selecting the
"Find Table End", "Teach Table
End", or "Enter Length" buttons.
8
Press "Main"
(Bottom right corner)
Press "Settings"
(Bottom right corner)
Verify all settings and ply counts, then press "Main" again
9
Note: Begin from step 10 if returning to your Saber E-Series and the
power was not switched off.
Set the spread using "Table End",
"Teach",or "Spread Length".
Note: When "Table End" is selected
the machine will automatically use
the Table End as endpoint. To teach
"Spread Length", press "Teach",
manually drive the spreader to your
start point, and press "End". "Spread
Length" requires entering a distance
relative to the start position.
7
Note: "Find Load End", the machine
travels until the limit switch is triggered.
When using " Teach Load End", drive
the machine to where you want to be-
gin the table, then press "Teach Load
End".
Note: "Find Table End", the machine travels
until the limit switch is triggered. To "Teach
Table End", the operator manually drives the
spreader to its end point, and "Enter Length"
requires typing in the length.
4
Press "Settings"
Press "Spread Length"
5
Set the start position using
"Home", "Teach", or "Offset From
Home".
Note: When "Home" is selected the
machine will automatically use the Load
End to start. To teach "Start Position",
press "Teach", manually drive the
spreader to your start point, and press
"Start. "Offset From Home" requires
distance relative to the home position.
11
Press "Settings"
(Bottom right corner)
Verify all settings and ply counts, then press "Main" again
(Along the bottom)
Manually set material to begin
spreading and conrm "Start
Direction". Press "Change
Direction" if necessary.
6
Note: The "Enter Length"
button is only enabled
when using "Find Load
End" to set the load posi-
tion.
Note: Begin from step 10 if returning to your Saber E-Series and the
power was not switched off. 12
Press "Start Spread"
to begin spreading.
Form CR-50-0528
Eastman
®
1. Spread/Rewind: Sets cradle direction.
2. Overfeed: Additional cradle control for automatic feeding. Less decreases material, more increases material.
3. Cradle Jog: Controls manual cradle feeding. Press to manually feed material.
4. Bidirectional Throttle: For manual spreading, controls direction and speed of machine. Also may be used
to stop automatic spreading by twisting and releasing.
5. Open/Close: Toggle to open/close cradle.
6. Main Power: Activates the main power. Twist right on, twist left off.
7. Main Display: Touchscreen; PC used for software and machine control.
8. E-Stop: Emergency stop. Push on, twist off.
9. Mirror: Used to view the material in the cradle.
10. Edge Control Sensor: Detects the edge of the material being spread.
WARNING
Equipment Starts
automatically -
can cause severe
injury
KEEP AWAY
21
4
6
2
8
9
8
710
5
3
Familiarization
Otros manuales de Equipos industriales de EASTMAN
EASTMAN
EASTMAN Kodak X-Omat 180 LP Manual de usuario
EASTMAN
EASTMAN TRIGGER PLUS Knifebox Manual de usuario
EASTMAN
EASTMAN Kodak X-Omatic 4 Manual de usuario
EASTMAN
EASTMAN HVN Manual de usuario
EASTMAN
EASTMAN Blue streak II 629X Manual de usuario
EASTMAN
EASTMAN RS2 Manual de usuario
EASTMAN
EASTMAN C Series Guía de configuración
EASTMAN
EASTMAN 1050VB Manual de usuario
EASTMAN
EASTMAN DYNAFIX DF 4800 Guía de configuración
EASTMAN
EASTMAN HHN Manual de usuario
