eaglelighting EL-HYP-124 Manual de usuario
1
1
DIMENSIONS DIAGRAM
INSTALLATION GUIDE
THIS GUIDE IS FOR THE FOLLOWING
LUMINAIRE VARIATIONS:
+T-Bar
+Surface Mounted
+Plaster Recessed
HYPERION Ag
+ PLEASE READ THIS GUIDE CAREFULLY BEFORE
INSTALLING OR MAINTAINING THIS EQUIPMENT.
+ DATA SHOULD BE USED AS AN INDICATION ONLY.
+ GOOD ELECTRICAL PRACTICES SHOULD BE FOLLOWED AT ALL TIMES.
+ MUST ONLY BE INSTALLED BY A LICENSED ELECTRICIAN.
SPECIFICATION
Luminaire’s light distribution is direct.
Denotes which light source/light sources
that can be supplied with the luminaire.
Several symbols next to the same
luminaire indicate that the luminaire is
available in different designs.
Luminaire is designed for the T5-light
source’s unique characteristics. The small
diameter of the fluorescent lamp has
created new conditions for light control.
IP classification:
IP20 : Protected against solid objects
greater than 12 mm, e.g. persons fingers.
Class I : Appliances with functioning
insulation. Equipped with an earth
termination.
Luminaire can be obtained in designs with
emLED.
Luminaire is available in designs for
conventional emergency lighting operation.
This luminaire is not suitable for covering
with thermally insulating material
RCM indicates a device’s compliance with
applicable ACMA technical standards.
www.eaglelighting.com.au/hyperion_ag
PRODUCT CODE LIGHT SOURCE/DESCRIPTION (NOM) DIMENSIONS
A B C CUTOUT WEIGHT
Hyperion Ag EXPOSED T-BAR
EL-HYP-114-_01-___ 1 x 14W T5 600 300 100
EL-HYP-124-_01-___ 1 x 24W T5 600 300 100
EL-HYP-128-_04-___ 1 x 28W T5 1200 300 100
EL-HYP-135-_07-___ 1 x 35W T5 1500 300 100
EL-HYP-154-_04-___ 1 x 54W T5 1200 300 100
Hyperion Ag SURFACE MOUNTED
EL-HYP-114-_11-___ 1 x 14W T5 600 300 100
EL-HYP-124-_11-___ 1 x 24W T5 600 300 100
EL-HYP-128-_14-___ 1 x 28W T5 1200 300 100
EL-HYP-135-_17-___ 1 x 35W T5 1500 300 100
EL-HYP-154-_14-___ 1 x 54W T5 1200 300 100
ACCESSORIES
EL-ACC-600-000 PLASTER FRAME ACCESSORY 600 300 102 605 310
EL-ACC-602-000 PLASTER FRAME ACCESSORY 1200 300 102 1205 310
EL-ACC-606-000 PLASTER FRAME ACCESSORY 1500 300 102 1505 310
A
C
B
Installation Instruction
WEIGHT:
A1
SHEET 1 OF 1
SCALE:1:1
DWG NO.
TITLE:
REVISION
DO NOT SCALE DRAWING
MATERIAL:
DATE
SIGNATURE
NAME
DEBUR AND
BREAK SHARP
EDGES
FINISH:
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN MILLIMETERS
SURFACE FINISH:
TOLERANCES:
LINEAR:
ANGULAR:
Q.A
MFG
APPV'D
CHK'D
DRAWN
DIFFUSER OPTIONS SUFFIX
Y19 -100
Y5 -200
Y7 -300
Y20 -600
CDP DELTA -800
VARIATION SUFFIX
Standard -000
DSI/STD terminal block -100
DALI/STD terminal block -200
Standard/Fused terminal block -400
DSI/Fused terminal block -500
DALI/Fused terminal block -600
BRISBANE
EAGLE LIGHTING QLD
53 Caswell Street
East Brisbane QLD 4169
P07 3891 0744
F 07 3891 0755
HEAD OFFICE | MELBOURNE
EAGLE LIGHTING VIC
17-19 Jets Court
Melbourne Airport VIC 3045
P 03 9344 7444
F03 9344 7433
SYDNEY
EAGLE LIGHTING NSW
Unit 4, 21 Mars Road
Lane Cove NSW 2066
P02 9420 5799
F02 9420 5988
EAGLE LIGHTING AUSTRALIA PTY LTD.
ABN 46 124 400 933
INSTALLATION INSTRUCTIONS
The Hyperion Ag luminaire is shipped as two seperate components, the Hyperion Ag
body and the diffuser.
Hyperion Ag | T-Bar
Step 1: Lift Hyperion Ag luminaire into ceiling cavity.
Step 2: Complete electrical connection.
Step 3: Position luminaire centrally within T-Bar.
Step 4: Remove plastic film from reflector.
Step 5: Ensure lamp is fitted correctly.
Step 6: Insert diffuser into luminaire.
Hyperion Ag | Plaster Recessed
The Plaster Recessed Hyperion Ag is also shipped with a Plaster Recessing
Acessory, which includes mounting brackets and fasteners.
Step 1: Cut-out the correct hole size in the ceiling for your Hyperion Ag luminaire.
Step 2: Lift plaster frame to plaster cut-out.
Step 3: Insert and fasten plaster recess brackets into slots as indicated in Diagram
A. Ensure fasteners are not overtightened.
Step 4: Remove lamp and reflector from luminaire.
Step 5: Lift Hyperion Ag into ceiling cavity.
Step 6: Complete electrical connection.
Step 7: Position luminaire centrally within plaster frame.
Step 8: Refit reflector into luminaire, remove plastic film and refit lamp.
Step 9: Insert diffuser into luminaire.
Hyperion Ag | Surface Mounted
Note: Surface Mounted Hyperion Ag luminaires must be hard wired.
Step 1: Lift surface mounting body to ceiling, feeding the supply cable through the
cable entry hole.
Step 2: Secure the body onto the mounting surface with appropriate fasteners (not
supplied) to suit mounting substrate.
Step 3: Complete electrical connection.
Step 4: Slide the Hyperion luminaire into the surface mounted body and
connect the earth lanyard to the end.
Step 5: Slide the end into the surface mount body.
GENERAL INFORMATION
+A qualified electrician, in accordance with
AS/NZS 3000:2007 wiring regulations
should carry out connection to mains
wiring.
+This unit must be EARTHED.
+Ensure that the rated voltage and
frequency requirements are compatible
with the available mains supply,
220-240V 50Hz
+Cleaning of reflectors and lenses should
be carried out using clean, soft and lint
free cloths and anti-static cleaning fluid.
+Do not carry out high voltage insulation
test i.e. 500/1000V this may damage the
fixtures electrical components.
HYPERION Ag
Diagram A.
CANBERRA
EAGLE LIGHTING ACT
M 0411 889 406
SURFACE MOUNT BODY
LUMINAIRE
SURFACE MOUNT END
Este manual sirve para los siguientes modelos
5
Otros manuales de Linterna de eaglelighting
