E-Service Nayax Manual de usuario
SALES@E-SERVICE.CO.UK WWW.E-SERVICE.CO.UK
01707 280 050
Nayax installation Guide
The complete guide to installing
the Nayax wireless card reader
1
3
5
7
6
8
9
4
2
Nayax Installation Guide
2
Figure 1 - Installed Nayax Layout
1
2
4
5
7
8
9
6
3
Nayax Installation Guide
3
Nayax VPOS/Onyx
This is the wireless card reader. The VPOS or Onyx
should be xed to the outside of the machine in
easy access to customers.
For detailed information on tting the VPOS/Onyx
unit, please refer to page 9.
Nayax AMIT 3
The Nayax AMIT 3 is the central unit of the Nayax
system and connects the Nayax components
together. The AMIT 3 should be placed inside the
machine
I/O Connector Cable
This cable plugs into the AMIT’s ‘I/O‘ socket and
connects it to the Nayax Interface Board. Please
note that the cable splits to include a plug that is
not used in most installations.
NAYAX Interface Board
This small circuit board plugs into the coin mech
through the socket that is usually connected to the
machine’s main control board. It connects the Amit
to the coin mech, number meter and main board.
PL1 Main Board Cable
This cable is attached to the machine’s main board
and is usually connected directly to the coin mech.
In the Nayax setup, the cable is plugged into the
interface board’s PL1 pin-socket.
Number Meter
This number meter attaches to the interface board
and records when a transaction is used. For detailed
instructions for manually attaching a number meter
to the interface board, please refer to page 5.
Antenna
The antenna screws into the top of the AMIT3 and
can be positioned internally to protect against van-
dalism or externally to maximise signal strength.
PL2 Wire Holes
The PL2 wire holes are used to connect the inter-
face board to the AMIT and number meter.
If manually connecting the I/O cable or number
meter to interface board, detailed instructions can
be found on page 4.
RJ45 / RJ6Connector Cable
This cable connects the external VPOS to the
internal AMIT 3. The cable must pass through the
hole made while tting the VPOS.
For detailed information on tting the VPOS unit,
please refer to page 9.
1
4
7
10
11
12
PL2
2
5
8
3
6
9
Wire Colour Wire Name PL2 Hole Number
Brown AC / DC + 3
Orange PULSE1\FUJI RXD 4
Blue EX PULSE INHIBIT 5
Green AC / DC - 7
Red GND 8
Yellow PULSE2\FUJI TXD Not used
Black VCC Not used
Nayax Installation Guide
4
To correctly wire the Nayax Interface Board, please follow the diagram above to
match the correct wires to the correct holes.
VPOS to Interface Board wiring guide
Figure 2
1
4
7
10
11
12
PL2
2
5
8
3
6
9
Wire Colour Wire Name PL2 Hole Number
Black (any wire) 10
Black (any wire) 11
Nayax Installation Guide
5
To correctly wire the number meter, please follow the diagram above to match the
correct wires to the correct holes.
Please note that the order of the wires is not important for the number meter.
As long as one wire is placed in hole 10 and the other is placed in hole 11, the number
meter should function correctly.
Number meter wiring guide
Figure 3
Nayax Installation Guide
6
Figure 4
Figure 5
Figure 6
Thomas software updating guide
Access the Control Module
Open the Machine and locate the Control Module, as seen in gure 4. Remove the bill validator to gain
access to the control module and open it’s hinged door.
Replace the software chip
Remove the chip from the inside of the control module’s door, as seen circled in red in gure 5.
Replace the old chip with the new software chip provided in the upgrade kit.
1.
2.
Nayax Installation Guide
7
Figure 7
Figure 8
Enable 10p coins for testing
On the large circuit board on the opposite side, locate the four switches marked ‘S2’, as seen circled
in red in gure 7. Flip the fourth switch to the on position, as seen in gure 8.
Test the newly activated software.
Test the software by dropping a 10p coin, it should give change for the same value that the Nayax tap
value should be, i.e £5, £10 or £20. Insert all other coins and notes and check the change given is correct.
If the change given is correct, close the control module, re-insert the note validator and proceed to
section 5. If the change is incorrect or you encounter other errors, replace the old software chip and call
E-Service support on 01707 280 050.
3.
4.
Nayax Installation Guide
8
Remove the plastic cover from the Thomas Machine door
Unscrew the four 7mm nuts that are circled in red in gure 9. Once the nuts are unscrewed, remove the
plastic cover, as seen in gure 10.
5.
Figure 9
Figure 10
Nayax Installation Guide
9
Place the provided template over the Thomas 3000
Print out the template on page 15 or 16 of this guide, depending onwhether you are installing the
VPOS or Onyx. Place the printed template over the Thomas machine, aligning the yellow arrow with
the indent corner as seen in gure 12.
CAUTION: Remember to print without scaling the page and use the printed ruler to
ensure that the printout is correctly sized.
Drill through the faceplate as marked on the printed template
Use a center punch to mark the drill points as shown on the template.
Drill holes for the screws and one large hole for the cable to pass though, sized according to the
printed template
Optionally, you may remove the inner back plate and shorten it to the red line, rather than drilling
though it. Take care to remove the circuit board on the right of gure 13 before removing the plate.
1.
2.
VPOS wireless card reader mounting guide
Figure 13
Figure 12
Figure 11
Nayax Installation Guide
10
Figure 15 Figure 16
Screw the VPOS/Onyx into the front of the machine
Position the VPOS/Onyx wireless card reader over the newly drilled holes and
screw it in from the back of the machine’s door, as seen in gure 16. Ensure
that the card reader is ush with the machine and correctly aligned before
tightening the screws.
4.
Insert the grommet for the connector cable
Once drilled, t the grommet into the 22mm hole, as seen in gure 14.
3.
Figure 14
Tabla de contenidos
Manuales populares de Terminal de pago de otras marcas
Ingenico
Ingenico iWL250B Manual de usuario
Optimum
Optimum M4230 Manual de usuario
Triton
Triton RL5000 Manual de usuario
Ingenico group
Ingenico group Lane/8000 Manual de usuario
Gilbarco
Gilbarco FlexPay IV CRIND Manual de instalación y operación
Infinite Peripherals
Infinite Peripherals Infinea Tab Lite Manual de usuario
