Dynabrade Dynangle 14200 Manual de usuario

Otros manuales de Lijadora de Dynabrade

Dynabrade

Dynabrade 300CE Guía

Dynabrade

Dynabrade 51611 Guía

Dynabrade

Dynabrade Dynafile II 40503 Guía

Dynabrade

Dynabrade 48520 Guía

Dynabrade

Dynabrade 51584 Guía

Dynabrade

Dynabrade Dynastraight 13201 Guía del usuario

Dynabrade

Dynabrade Dynabug Model T 10485 Guía del usuario

Dynabrade

Dynabrade 53271 Guía

Dynabrade

Dynabrade 52503 Instrucciones de instalación

Dynabrade

Dynabrade 50320 Manual de usuario

Dynabrade

Dynabrade Dynalocke 52760 Guía

Dynabrade

Dynabrade 53521 Guía

Dynabrade

Dynabrade 50347 Guía del usuario

Dynabrade

Dynabrade 57550 Manual de usuario

Dynabrade

Dynabrade X32V Manual de usuario

Dynabrade

Dynabrade 55126 Guía

Dynabrade

Dynabrade Dynorbital 57610 Manual de usuario

Dynabrade

Dynabrade 57400 Manual de usuario

Dynabrade

Dynabrade 59302 Instrucciones de funcionamiento

Dynabrade

Dynabrade 52450 Manual de usuario

Dynabrade

Dynabrade 52656 Guía

Dynabrade

Dynabrade 4657971919 Manual de usuario

Dynabrade

Dynabrade 52560 Guía

Dynabrade

Dynabrade 52520 Manual de usuario

Manuales populares de Lijadora de otras marcas

Oliver

Oliver 6305 Manual de usuario

Jet

Jet 22-44 Pro-3 Manual de servicio

Makita

Makita M9204 Manual

Makita

Makita M9204 Manual de usuario

Craftsman

Craftsman 351.215131 Manual de usuario

Clarke

Clarke Woodworker CBS1-5B Manual de instrucciones

Chicago Pneumatic

Chicago Pneumatic CP9778 Manual de usuario

Nitto Kohki

Nitto Kohki BB-20 Manual de usuario

Ferm

Ferm FEOS-135 Manual de usuario

Unior

Unior 1510 Manual de usuario

stayer

stayer ls1200 Manual de usuario

Jet

Jet JSG-96 Manual de servicio

Parkside

Parkside PDS 290 B2 Manual de usuario

Status

Status XPA Series Manual de usuario

Clarke

Clarke EZ Sand Manual de usuario

Craftsman

Craftsman 113.22521 Manual de usuario

Craftsman

Craftsman 113.225831 Manual de usuario

CLAS

CLAS OP 1429 Manual de usuario

Disassembly Instructions - 0.7 hp. Dynangle Air Motor

Models: 14200

Important: Use these instructions along with the tool parts page or manual.

Notice: Shut off the air supply and depress throttle lever to deplete the remaining air.

• Carefully disconnect the tool from the air supply hose. • Remove the cover and the abrasive

belt. • Use the Special Repair Tools designed for the disassembly and assembly of this motor.

Motor Disassembly:

1. Use a 1/8" hex key to loosen the 95530 Screw.

Remove the motor from the belt housing.

1/8" hex key

1/8" Hex Key

2. Use a 19 mm wrench to hold the motor spindle. By hand, or with groove pliers, grasp the

drive wheel and remove it. Turn counterclockwise.

19 mm Wrench

3. Carefully fasten the 01739 Housing in a vise with aluminum or bronze jaws so that the

spindle is pointing up.

Use a 1-1/2" crowfoot wrench to remove the 01748 Exhaust Cover.

Turn counterclockwise.

Remove the 01744 Silencer.

1-1/2" crowfoot wrench

Pull the motor out of the housing.

4. Fasten the 96346 Bearing Separator (2") around the 01028 Cylinder. Place the separator

and the motor in the 96232 Arbor Press (#2) so that the rotor spindle is pointing down.

Use a 5/32" or 4 mm diameter flat end drive punch to push the rotor out of the 02649

Bearing.

96346 Bearing Separator

5. Use the 96213 Bearing Removal Tool and the arbor press to remove the 02649 Bearing

from the rear bearing plate.

96346 Bearing Separator

96213 Bearing Removal Tool

6. Fasten the 55025 Rotor in the vise with aluminum or bronze jaws and use an adjustable

wrench to remove the 01708 Rotor Nut. Turn counterclockwise.

Remove the 01007 Bearing, 01008 Bearing Plate, shims, and 01010 Spacer.

Motor Disassembly Completed.

Clean and inspect parts before assembling.

Assembly Instructions - 0.7 hp. Dynafile III Air Motors

Motor Assembly:

1. Install the 01010 Spacer onto the rotor.

Install .003" (~0.80 mm) shim thickness into the 01008 Front Bearing Plate.

Install the 01007 Bearing into the front bearing plate.

Install the bearing and plate onto the rotor.

.003" (~0.80 mm)

shim thickness

01010 Spacer

2. By hand, install the 01708 Rotor Nut. Pull the front bearing plate forward to take movement

out of the bearing. Check the clearance between the rotor and plate.

Use a .001" (~0.03 mm) thick feeler gauge. Notice: The clearance should be

.001"-.0015" (~0.03-0.04 mm). If the rotor/plate clearance needs adjustment, repeat

steps 1 and 2. Remove or add shims as required.

.001"-.0015"

(~0.03-0.04 mm)

3. Use a 19 mm crowfoot and a torque wrench to tighten the 01708 Rotor Nut.

(T to 17 N•m/~150 in. lbs.)

T to 17 N•m/~150 in. lbs.