Dynabrade 4657971919 Manual de usuario

Disassembly Instructions – Dynabug Sander

Important: Use these instructions along with the tool parts page or manual.

Notice: To avoid damage, use the special repair tools contained in the 57098 Motor Repair Kit.

Shut off the air supply and deplete air from the hose. Disconnect the tool from the air supply.

Motor Disassembly:

1. Position the 57092 Repair Collar around the housing.

Fasten the sander in a vise with the sanding pad facing up. Notice: Do not over tighten

the sander in the vise. Over tightening will make it difficult to remove the 57059 Lock

Ring. (SEE STEP #3)

Use a 3 mm hex key to remove the pad screws (4).

57092 Repair Collar

3 mm hex key

Use a 3/16" hex key to remove the 96168 Screw.

Use a Phillips screwdriver to remove the 96114 Screws (6).

Remove the 57825 Pad Top.

3/16" hex key

2. Use a slot-blade screwdriver to loosen the 96116 Clamp. Remove the clamp, 57822 Boot

and 57823 Pad Mount.

3. Use the 56058 Lock Ring Wrench to loosen the 57059 Lock Ring. Turn counterclockwise.

4. Pry-up, under the motor shaft balancer to remove the air motor from the housing.

Remove the 57054 Rear Ring from the inside of the housing.

5. Use retaining ring pliers to remove the 95626 Retaining Ring.

6. Fasten the 96346 Bearing Separator (2") around the 57058 Cylinder. Place the bearing

separator and motor in the 96232 Arbor Press (#2) with the counterweight pointing down.

Use the arbor press and a 5/16" or 8 mm diameter flat-end press tool to push the shaft

out of the 01206 Bearing.

7. Remove the rotor, vanes, key, and front bearing plate.

Use the bearing separator and the arbor press ram to remove the 57088 Bearing.

96346 Bearing Separator

8. By hand, or with the arbor press, use the 96214 Bearing Removal Tool to remove the 01206

Bearing from the 57056 Rear Bearing Plate.

9. Balancer Bearing and Shaft Disassembly:

a) Fasten the counterweight in a vise with aluminum or bronze jaws so that the hex of the

57069 Balancer Shaft is pointing up. Use a thin slot-blade screwdriver to pick-out the end

of the 95630 Snap Ring and remove the snap ring from the motor shaft balancer.

96214 Bearing Removal Tool

b) To break the adhesive bond, use two flat-blade screwdrivers (large) to pry-up on the

balancer shaft and bearing. Notice: If necessary, use a HEAT GUN to apply heat to

the counterweight.

Use the 56056 Bearing Puller to remove the balancer shaft and the 56052 Bearing.

c) Fasten the bearing separator between the 56052 Bearing and the hex end of the 57069

Balancer Shaft.

Place the bearing separator and the balancer shaft in the arbor press with the hex

end pointing down. Use the arbor press ram to break the adhesive bond.

Use a 5/16" or 8 mm diameter flat-end drive punch as a press tool to push the balancer

shaft out of the 56052 Bearing.

Remove the 59084 V-Seal.

Motor Disassembly Completed.

RAM

Otros manuales de Lijadora de Dynabrade

Dynabrade

Dynabrade Mini-Dynafile II 15003 Guía

Dynabrade

Dynabrade 18066 Guía

Dynabrade

Dynabrade 51582 Guía

Dynabrade

Dynabrade 59302 Instrucciones de funcionamiento

Dynabrade

Dynabrade 59306 Guía

Dynabrade

Dynabrade 58035 Manual de instalación y operación

Dynabrade

Dynabrade Dynabug 57811 Manual de usuario

Dynabrade

Dynabrade Dynorbital 57610 Manual de usuario

Dynabrade

Dynabrade 48500 Guía

Dynabrade

Dynabrade Dynorbital-Spirit 21000 Manual de usuario

Dynabrade

Dynabrade 57400 Manual de usuario

Dynabrade

Dynabrade 57240 Manual de usuario

Dynabrade

Dynabrade X32V Manual de usuario

Dynabrade

Dynabrade 57900 Guía

Dynabrade

Dynabrade 10390 Guía del usuario

Dynabrade

Dynabrade 52900 Manual

Dynabrade

Dynabrade Autobrade Red 18180 Guía del usuario

Dynabrade

Dynabrade Nitro ROB1 Series Guía

Dynabrade

Dynabrade 10725 Manual de usuario

Dynabrade

Dynabrade 50304 Manual de usuario

Dynabrade

Dynabrade 57101 Guía del usuario

Dynabrade

Dynabrade 51611 Guía

Dynabrade

Dynabrade 10727 Manual de usuario

Dynabrade

Dynabrade 51612 Guía

Manuales populares de Lijadora de otras marcas

Oliver

Oliver 6305 Manual de usuario

Jet

Jet 22-44 Pro-3 Manual de servicio

Makita

Makita M9204 Manual

Makita

Makita M9204 Manual de usuario

Craftsman

Craftsman 351.215131 Manual de usuario

Clarke

Clarke Woodworker CBS1-5B Manual de instrucciones

Chicago Pneumatic

Chicago Pneumatic CP9778 Manual de usuario

Nitto Kohki

Nitto Kohki BB-20 Manual de usuario

Ferm

Ferm FEOS-135 Manual de usuario

Unior

Unior 1510 Manual de usuario

stayer

stayer ls1200 Manual de usuario

Jet

Jet JSG-96 Manual de servicio

Parkside

Parkside PDS 290 B2 Manual de usuario

Status

Status XPA Series Manual de usuario

Clarke

Clarke EZ Sand Manual de usuario

Craftsman

Craftsman 113.22521 Manual de usuario

Craftsman

Craftsman 113.225831 Manual de usuario

CLAS

CLAS OP 1429 Manual de usuario