DX Engineering DXE-RRMX2X8 Manual de usuario

2 x 8 Remote Antenna Smart

Two Radio Switch System

DXE-RRMX2X8

DXE-RRMX2X8-INS Revision 0a

1200 Southeast Ave. - Tallmadge, OH 44278

Phone: (800) 777-0703 ∙ Tech Support and International: (330) 572-3200

Fax: (330) 572-3279 ∙ E-mail: [email protected]

Introduction

The 2 x 8 Remote Antenna Smart Two Radio Switch System DXE-RRMX2X8 uses a DXE-

RR2X8 remote switch, DXE-MX2X8 interface unit and two DXE-CC-8A control consoles.

The two DXE-CC-8A control consoles supply the BCD switching signals to the DXE-MX2X8

interface unit which then sends the appropriate signals to the DXE-RR2X8 remote switch to select

one of the eight output ports for each DXE-CC-8A control console.

The dual star arrangement of 24 internal relays provide greatly improved power handling, port-to-

port isolation and SWR over conventional switches and allow connection of the eight antenna

output ports to either the master or slave input ports.

The system offers virtually no loss at HF and excellent low-loss performance (less than 0.16 dB

loss) on six meters.

Each control console (A and B) can select one of 7 or 8 positions available. When one operator has

a particular position selected, the other operator is locked out of that position - first come, first

served.

Features

Enclosed relays provide exceptional performance and are moisture resistant. The DXE-RRMX2X8

system can be used to simultaneously select multiple output ports as well as conventional one-of-

eight antenna switching. This allows the DXE-RR2X8B to be used in complex antenna systems as

well as traditional switching arrangements. Ports that are not selected are grounded.

The DXE-RRMX2X8 system also uses removable screw terminal plugs for the control cables. The

removable plugs greatly simplify installation by eliminating the need for soldering. Disassembly is

not required for control wiring access.

The DXE-RRMX2X8B also offers the following features:

RF Shielded Weatherproof Housings - unique protection

Excellent Port-to-Port Isolation; greater than 70 dB at 30 MHz, worst case.

Ports not selected are grounded

High-RF tolerant UHF connectors

Enclosed 16 ampere RF relays

Safe 12 volt DC relay operation

MOVs for surge protection on control lines

RF bypass capacitors

Includes two DXE-SSVC-2P Stainless Steel

V-Clamps for mounting

The DXE-MX2X8 interface unit interfaces

between the DXE-RR2X8 and the two DXE-CC-8A control consoles for seamless

operation

The two DXE-CC-8A control consoles have LED indicators and provide the BCD

outputs to the DXE-MX2X8 interface unit

Overall Wiring Diagram

This diagram shows the overall wiring scheme. Once familiar with this set up, making the actual

cables will be easier

DXE-CW9S is a shielded control cable that has 10-conductors and works very well for running

control signals for the DXE-RR2X8 and DXE-MX2X8.

Note: Do not seal the connectors! The connectors are recessed inside a drip edge that prevents

water from getting into connectors. The cover-to-connector plate junction is not sealed so

the unit can "breathe” and eliminate condensation.

MIL and SIL Safety Mode

One DXE-CC-8A Control Console is located next to each radio. Each operator can select their

desired antenna port using the knob on the DXE-CC-8A. A Green LED on the DXE-CC-8A will

light up showing which position is selected.

There are two internal jumpers in the DXE-MX2X8 interface

unit called MIL and SIL. These jumpers are in place as a

factory default.

When one antenna port is selected by operator “A” and the

operator “B” tries to select it, not only does that operator “B”

not connect to the same port operator “A” is on, the operator

“B” is sent to port number 8 (usually connected to a dummy

load) to avoid having operator “B” accidently transmit into an

open.

This same safety feature is used when ever one operator tries to select an antenna port that the other

operator is currently connected to.

Caution: If the jumpers are removed, then the Safety mode is no longer in operation and all 8 ports are used

for antennas. If operator “A” selects the same port that operator “B” has selected, operator “A” will not hear

anything (no port selected). Care is then needed so operator “A” does not transmit into an open.

The two signals MIL and SIL can be monitored (see terminals 9 & 10 on page 7). When the loser

(operator trying to connect to an antenna that the other operator is already connected to) - that signal

will go high (+12 VDC).

MIL A = Master Radio “A”. Will go to +12 VDC if it is the ‘loser’.

SIL B = Slave Radio “B”. Will go to +12 VDC if it is the ‘loser’.

One optional suggestion for a visual feedback for the MIL and SIL signals is to connect LEDs’ with

the appropriate sized current limiting resistors so the LEDs will light up when there is a “loser”

conflict.

NOTE: If MIL and SIL are used, it is suggested that port #8 be connected to an adequate size

dummy load.

If MIL and SIL are not used, port #8 can be connected to an 8th antenna.

Caution: Never switch antennas while transmitting. Hot switching with power will create a

sustained arc that damages relay contacts. When switching ports, allow 15 ms before transmitting

to avoid damaging the switch. This type of damage is NOT covered under warranty.

Wiring the Connections

1. Connections for the wire are made on the green headers. Loosen each

terminal screw until it is near flush with the top of the connector

block.

2. Strip approximately 1/4" insulation from the wire end and connect each wire to a terminal by

sliding the wire completely into the wire connection hole. Using a small flat blade screwdriver,

tighten the associated screw until the wire is firmly gripped in place as shown. (Your control

wire color sequence may vary).

Take caution to ensure just the wire is clamped in place, not the wire's

insulation which would cause an open or intermittent connection. Do not

over tighten the screw so much that the wire is cut instead of being firmly

gripped.

The green connectors are in two parts and the top part (plug) can be removed

by pulling it straight off. This will allow easier wire replacement or servicing as needed. When

pushing a connector back in place, ensure you press straight inward and the plug is fully seated.

Using two ten-wire cables, connect the DXE-RR2X8 to the DXE-MX2X8. Master to Master, Slave

to Slave. Wiring is G to G, 1 to 1, 2 to 2, 3 to 3, etc.

Two longer 5-wire cables connect from the DXE-MX2X8 to the two DXE-CC-8A Control

Consoles using the BCD connectors. The BCD switching signals, Ground, +12 VDC and the MIL

and SIL signals are on these cables. The two DXE-CC-8A control units are located near their

associated radio.

DXE-CW9S is a shielded control cable that has 10-conductors and works very well for running

control signals for the DXE-RR2X8, DXE-MX2X8 and DXE-CC-8A units.

When connecting the short cables from the DXE-RR2X8 to the DXE-MX2X8 ensure the ten-wire

cables are wired the same way at both ends to avoid un-necessary troubleshooting. Use the chart

below to record which color wire is connected to each terminal connection of each cable.

DXE-RR2X8

Master

Connector

Control Wire Color

Master

Connector

DXE-MX2X8

M=Master

S=Slave

Slave

Connector

Control Wire Color

Slave

Connector

DXE-RR2X8

DXE-MX2X8

The DXE-MX2X8 is connected to the two DXE-CC-8A control consoles. One is marked as “Radio

A” the second is marked as “Radio B”. Two control wire cables are used (one for each DXE-CC-

8A) to avoid having another break-out cable in the radio room.

The control signals are BCD logic. Along with these BCD signals there are four additional wires

used. One for Ground, one for +12 VDC, one for MIL and one for SIL (more on MIL and SIL

later).

The ten-pin green connector located on the DXE-MX2X8 is used to for two BCD control cables to

the two DXE-CC-8A BCD input Green Connectors (5-pin).

MX2X8

Signal

Name

Wire Color

CC-8A

“A”

CC-8A

“B”

External

GND

Ground

+12 VDC

Master A

Master B

Master C

Slave A

Slave B

Slave C

MIL

SIL

MX2X8

Signal

Name

Wire Color

CC-8A

“A”

CC-8A

“B”

External

DXE-CW9S is a shielded control cable that has 10-conductors and works very well for running

control signals for the DXE-RR2X8 remote switch, DXE-MX2X8 interface unit and the two DXE-

CC-8A control consoles..

Note: Do not seal the connectors! The connectors are recessed inside a drip edge

that prevents water from getting into connectors. The cover-to-connector

plate junction is not sealed so the unit can "breathe” and eliminate

condensation.

Power, Ground, MIL, SIL Connections

Referring to the previous wiring diagrams there are five wires shown not connected (GND, +12

VDC, MIL, SIL, GND).

+12 VDC is the line that needs station power (usually +13.8 VDC nominal) connected to it. This

line supplies the voltage needed to operate the relays.

The two GND (Ground) wires shown need to be connected to the ground side of the station power.

As in the diagram shown, you will have to supply a ground wire from (in this example) from Slave

Radio “B” GND to the same ground that Master Radio “A” is connected to. This connects each

controller to the common ground.

Additionally, each DXE-CC-8A control console unit has its own power connection (not shown in

the diagram for clarity) that would be connected to the same +13.8 VDC (nominal) station power

supply.

The MIL and SIL wires are explained earlier in this manual and their use is optional.

DXE-RR2X8 and DXE-MX2X8 Installation

1. Secure the DXE-RR2X8B switching unit using the included DXE-SSVC-2P stainless steel V-

Saddle Clamp.

Mount the DXE-MX2X8 close to the DXE-RR2X8B

to keep the interface cable lengths between these units

to a minimum using the included DXE-SSVC-2P

stainless steel V-Clamp.

The two pictures on this page show just two versions

of mounting the units. Your set up may vary.

The connectors must face downward to avoid

moisture.

Use Never-Seez®, Anti-Seize or Jet Lube SS-30 on

all stainless steel hardware to prevent galling.

2. Fasten all cables to the mounting mast or tower to

relieve strain, and gently droop the cables to form a

drip loop (do not use tight bends with coaxial cable).

Install both of the units with the connectors facing

down and use gradual bends or loops in heavy wires.

If the system is mounted to a wooden pole or building,

a wide copper flashing or heavy wire or strap should

be connected from the mounting bracket to a good

ground.

Note: Do not seal the connectors! The connectors are

recessed inside a drip edge that prevents water

from getting into connectors. The cover-to-

connector plate junction is not sealed so the unit

can "breathe” and eliminate condensation.

Very Simplified Control Logic

When selecting the various switch positions, the first control console that selects a particular position

has precedence. This means if Radio “A” selects output port #3, them Radio “B” cannot use port #3 at

the same time. Radio “B” will not connect to port #3. The operator will know that there is no antenna

selected since there will be no audio from any signals coming into Radio “B”.

A very simplified schematic is shown:

Master Radio “A” and Slave Radio “B” can never use

the same output port at the same time.

(Ports not selected are grounded)

Caution: Never switch antennas while transmitting. Hot switching with power will create a

sustained arc that damages relay contacts. When switching ports, allow 15 ms before transmitting

to avoid damaging the switch. This type of damage is NOT covered under warranty.

Tabla de contenidos

Otros manuales de Antena de DX Engineering

DX Engineering

DX Engineering DXE-SWA-148 Manual de usuario

DX Engineering

DX Engineering DXE-60VA-1P Manual de usuario

DX Engineering

DX Engineering DXE-MBV-2 Manual de usuario

DX Engineering

DX Engineering DXE-OCF-KIT Manual de usuario

DX Engineering

DX Engineering DXE-MBV5AS-INS Manual de usuario

DX Engineering

DX Engineering DXE-AOK-17M Manual de usuario

DX Engineering

DX Engineering Hummelmasten Mini XL Manual de usuario

DX Engineering

DX Engineering DXE-ATK65 Manual de usuario

DX Engineering

DX Engineering DXE-SWA-070 Manual de usuario

DX Engineering

DX Engineering DXE-MBVE-2 Manual de usuario

DX Engineering

DX Engineering Hot Rodz DXE-HR-2P Manual de usuario

DX Engineering

DX Engineering DXE-160VA-1 Manual de usuario

DX Engineering

DX Engineering DXE-WA-070 Manual de usuario

DX Engineering

DX Engineering DXE-8040-30AOK Manual de usuario

DX Engineering

DX Engineering DXE-AOK-80M Manual de usuario

DX Engineering

DX Engineering DXE-8040VA-1 Manual de usuario

DX Engineering

DX Engineering DXE-MBVE-5A Manual de usuario

DX Engineering

DX Engineering DXE-NVIS-8040 Manual de usuario

DX Engineering

DX Engineering DXE-AL24 Manual de usuario

DX Engineering

DX Engineering OMNI-TILT DXE-OMNITILT-1 Manual de usuario

DX Engineering

DX Engineering SkyHawk 3X10 Manual de usuario

DX Engineering

DX Engineering DXE-RG-5000HD Manual de usuario

DX Engineering

DX Engineering DXE-MBVE-5A Manual de usuario

DX Engineering

DX Engineering DXE-TW2010 Manual de usuario

Manuales populares de Antena de otras marcas

Alfa Network

Alfa Network APA-L01 Manual de usuario

Naval

Naval PR-422CA Manual de usuario

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Manual de usuario

TERK Technologies

TERK Technologies TV44 Manual de usuario

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Manual de usuario

HP J8999A Manual de usuario

MobilSat

MobilSat MSP-S Manual de usuario

Steren

Steren ANT-UHF 13 Manual de usuario

Novatel

Novatel 600-G Manual de operación

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Manual de usuario

TRENDnet

TRENDnet TEW-AO12O Manual de usuario

Radio Shack

Radio Shack 15-1837 Manual de usuario

CommScope

CommScope CMAX-OMFX-43M-I53 Manual de usuario

Ramsey Electronics

Ramsey Electronics DAP25 Manual de usuario

COBHAM

COBHAM SAILOR 800 VSAT Manual de uso y cuidado

Trango Systems

Trango Systems AD900-9 Manual de usuario

Steren

Steren ANT-100 Manual de usuario

Proxim

Proxim 5054-PA-23 Manual de usuario