Duronic MPS Manual de usuario
MPS - Manual Projector Screen
PLEASE READ ALL THE INSTRUCTIONS BEFORE USE
2
3
English Manual
Manuel d’utilisation en français
Gebrauchsanleitung auf Deutsch
Manual de Instrucciones en Español
Manuale D’istruzioni In Italiano
Instrukcja obsługi. Polski
Gebruikershandleiding Nederlands
5
11
17
23
29
35
41
Contents
4
5
English Manual
6
Before You Begin
Assembly Instructions
• Clear a large enough area to assemble the screen. Make sure the area is
larger than the sides of the screen.
• Assembly of the screen requires at least two people for some of the steps.
• Do not assemble the screen in areas of high temperature to avoid
incurring any damage to the screen.
• Ensure that you read through this manual entirely before beginning to
assemble the screen.
1. Ensure your assembly area is clean and completely clear.
2. Unpack all of the parts from the box and lay them out in an orderly way. Do
not unroll the screen yet.
3. Place the screen on the at even surface. In order to protect the screen
from getting marked or stained, ensure that the screen is kept away from
dust and dirt.
4. Decide on a location for your screen. The MPS screen can be installed in
three ways:
Tools Required for Assembly
• Phillips screwdriver
• Spirit level
• Allen key (included in the box)
• Drill (if installing onto a wall)
7
Wall Mounted:
Using the holes on the back of the brackets to guide
you, hold the screen up onto the wall where you wish
to install it and mark the two places where you need
to put the screws.
a. Use a spirit level to check that the screen will
be level and straight on the wall.
b. Set the screen aside.
c. Use a drill to make two holes in the places
you marked, ensuring they are the same
size to correspond with your raw plugs. Then
insert raw plugs.
Spacer brackets Eyebolt screws
Note: The MPS comes with some standard raw plugs for brick walls;
however you may need to nd suitable alternatives depending on the
material of your wall.
d. Lift the projector screen into place, and using a screwdriver, insert the
screws through the brackets and into the aligning holes. Tighten in
place.
e. Check to make sure the screen is level on the wall.
Ceiling Mounted:
You can hang your projector from ceiling-height in two ways: directly from the
ceiling using eyebolt screws, or from the top of the wall using spacer brackets.
For both kinds of installation, you may also need S-shaped hooks.
As ceilings can be made of different materials - some weaker than others
- you will need to assess if your ceiling is capable of holding the weight
of the screen and if it’s safe to do so. Then, make sure you choose the
right xings for your type of ceiling.
8
Operating Instructions
Tripod Mounted:
The brackets have holes to allow the screen to
be mounted on to tripods. In most cases, you will
need two tripod stands (one for each end of the
screen). Usually you will need two hooks and/or two
S-shaped hooks.
Please note: The only xings included in the
box are raw plugs for brick walls. If you require
alternative xings such as tripod stands, spacer
brackets or eyebolt screws you will need to buy
these separately.
Extending the Screen
Use the handle to slightly extend the screen out from the case, then continue
to extend until you reach the desired height. Gently tug the screen downwards
a little to automatically lock the screen into place.
Note: If the screen fails to lock in place, repeat the gentle tugging motion until
it is locked.
Retracting the Screen
To retract the screen back into the case, use the handle to pull the screen
down slightly and release the internal locking catch of the roller. The screen
will automatically roll back up into the case by itself. Do not let go of the screen
while it rolls back up, instead hold it and slowly guide it back into the case.
This will take care of the screen and prevent any damage occurring.
Cautions:
• Make sure that the screen is extended from the casing gently.
• Make sure that the screen is retracted back into the casing after each use.
Failure to do so may result in damage to the locking catch and can also
allow the screen to gather dust.
9
Cleaning
When not in use, keep your screen rolled up to keep it dust-free. If the screen
or casing gather dust, simply clean with a dry cloth or duster.
The screen is made of PVC. If the screen has a mark or stain that needs to
be removed, use a wet cloth with a mild soap to gently clean the screen. Use
minimal pressure to prevent damaging the fabric.
Do not use any abrasive chemicals or cleaning agents on any part of the
screen or casing.
Retract
Extend
Troubleshooting
Problem Solution
The screen does not
go up or down
If the screen is jammed and is stuck either fully
retracted or fully extended, then you will need to
contact Duronic directly for further advice.
Screen does not
extend to the correct
length
If the screen does not extend to the correct length,
try rolling the screen back up fully, then try again to
extend the screen.
Screen does not
completely retract
If the screen does not retract fully into the
projector casing, try to gently pull the screen down
completely and then try again to roll it back up into
the casing.
10
Warranty
1 Year Guarantee from Shine-Mart Ltd, Trademark owners of Duronic Products.
NOTE: THESE STATEMENTS DO NOT AFFECT YOUR STATUTORY RIGHTS AS A
CONSUMER
This product has been manufactured under the strictest or quality control procedures, and
using the highest quality of materials, to ensure excellent performance and reliability. It will
give very good and long lasting service, provided it is properly used and maintained. The
product is guaranteed for 1 years from the date of original purchase. If any defect arises due
to a faulty materials or poor workmanship, the faulty product must be returned to the original
place of purchase. Refund or replacement is at the discretion of that company.
Duronic Products are offered with a 1 year guarantee under the following conditions:
1. The product must be returned to the retailer with original proof of purchase.
2. The product must be installed and used in accordance with the instructions
contained in this operating manual.
3. It must be used only for domestic purposes.
4. It does not cover wear and tear, malicious damage, misuse, neglect,
inexpert repairs or consumable parts.
5. Shine-Mart Ltd has no responsibilities for accidental or consequential loss or damage.
6. Shine-Mart Ltd are not liable to carry out any type of servicing work,
under the guarantee
7. Valid in the UK only
This product is tted with CE:1363 plug and fuse
Imported by Shine-Mart Ltd, RM3 8SB
Information on waste Disposal for Consumers of
Electrical & Electronic Equipment.
This mark on a product and/or accompanying documents indicates that when it
is to be disposed of, it must be treated as Waste
Electrical & Electronic Equipment, (WEEE).
Any WEEE marked products must not be mixed with general household waste,
but kept separate for the treatment, recovery and recycling of the materials used.
For proper treatment, recovery and recycling; please take all WEEE marked
waste to your Local Authority Civic waste site,
where it will be accepted free of charge.
If customers dispose of Waste Electrical & Electronic Equipment correctly, they
will be helping to save valuable resources and preventing any potential negative
effects upon human health and the environment, of any hazardous materials that
the waste may contain.
Otros manuales para MPS
1
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Idiomas:
Otros manuales de Accesorios para proyectores de Duronic
Duronic
Duronic PB03XB Manual de usuario
Duronic
Duronic FFPS Manual de usuario
Duronic
Duronic MPS Manual de usuario
Duronic
Duronic BPS Manual de usuario
Duronic
Duronic FPS Manual de usuario
Duronic
Duronic TPS Manual de usuario
Duronic
Duronic FPS Manual de usuario
Duronic
Duronic PB04XL Manual de usuario
Duronic
Duronic EPS Manual de usuario
