DURKOPP ADLER DAC classic 281 Manual de usuario

281

Operating Manual

Property of Dürkopp Adler AG and protected by copyright. Any reuse

of these contents, including extracts, is prohibited without the written

approval in advance of Dürkopp Adler AG.

Table of contents

Operating manual 281 Version 06.0 - 05/2013 1

1 About this manual .................................................. 3

1.1 Scope of application of the manual........................... 3

1.2 Damage during transport.......................................... 3

1.3 Limitation of liability................................................... 3

1.4 Symbols used ........................................................... 4

2 Safety instructions ................................................. 5

2.1 General safety instructions ....................................... 5

2.2 Signal words and symbols used in safety

instructions................................................................ 7

3 Performance description ....................................... 9

3.1 Features.................................................................... 9

3.2 Declaration of conformity.......................................... 9

3.3 Intended use............................................................. 9

3.4 Technical data ........................................................ 10

3.5 Additional equipment .............................................. 11

4 Device description................................................ 15

5 Operation............................................................... 17

5.1 Switching the power supply on and off ................... 17

5.2 Inserting and replacing the needle.......................... 18

5.3 Threading in the needle thread............................... 20

5.4 Inserting and winding on the hook thread............... 23

5.5 Setting the bobbin filling quantity............................ 25

5.6 Replacing the hook thread bobbin.......................... 26

5.7 Thread tension........................................................ 27

5.7.1 Adjusting the needle thread tension ....................... 28

5.7.2 Adjusting the hook thread tension .......................... 30

5.8 Setting the thread regulator .................................... 32

5.9 Adjusting the stitch length....................................... 34

5.10 Setting the sewing foot pressure ............................ 35

5.11 Lifting the sewing foot............................................. 36

5.12 Locking the sewing foot in place in the

upper position ......................................................... 37

5.13 Pushbutton on the machine arm............................. 38

5.14 Operating the controller .......................................... 39

5.14.1 Control panel for the controller ............................... 39

5.15 Sewing.................................................................... 42

Table of contents

Operating manual 281 Version 06.0 - 05/20132

6 Maintenance.......................................................... 45

6.1 Cleaning work......................................................... 45

6.2 Lubrication .............................................................. 47

6.2.1 Hook lubrication...................................................... 48

6.2.2 Gear lubrication ...................................................... 49

6.3 Repairs ................................................................... 50

7 Set-up..................................................................... 51

7.1 Checking the scope of delivery............................... 51

7.2 Removing the transport securing devices............... 52

7.3 Fitting the frame components ................................. 53

7.4 Completing the table plate...................................... 54

7.5 Fastening the table plate to the frame .................... 55

7.6 Setting the working height ...................................... 56

7.7 Controller ................................................................ 57

7.7.1 Fitting the controller ................................................ 57

7.7.2 Fit the pedal and setpoint device............................ 58

7.8 Inserting the machine upper section....................... 59

7.9 Attaching the upper section retaining strap ............ 60

7.10 Attaching the oil can ............................................... 60

7.11 Fitting the knee lever .............................................. 61

7.12 Attaching the control panel ..................................... 62

7.13 Electrical connection............................................... 63

7.13.1 Checking the mains voltage.................................... 63

7.13.2 Connecting the controller........................................ 63

7.13.3 Establishing equipotential bonding ......................... 65

7.14 Sewing test ............................................................. 66

8 Disposal................................................................. 67

9 Appendix ............................................................... 68

About this manual

Operating manual 281 Version 06.0 - 05/2013 3

1 About this manual

1.1 Scope of application of the manual

This manual describes the intended use and the set-up of the

special sewing machine 281.

It applies to all submodels listed in Section  3 Performance

description.

1.2 Damage during transport

Dürkopp Adler cannot be held liable for any damage during

transport. Check the delivered product immediately after receiving

it. Report any damage to the last transport manager. This also

applies if the packaging is not damaged.

Keep the machines, devices, and packaging material in the

condition they were at the time the damage was identified.

That secures any claims towards the transport company.

Report all other complaints to Dürkopp Adler immediately after

receiving the product.

1.3 Limitation of liability

All information and notes in this operating manual have been

compiled in accordance with the latest technology and the

applicable standards and regulations.

The manufacturer accepts no liability for any damage due to:

• Failure to observe the instructions in the manual

• Improper use

• Unauthorized modifications to the machine

• The deployment of untrained personnel

• Damage during transport

• Using spare parts not approved

About this manual

Operating manual 281 Version 06.0 - 05/20134

1.4 Symbols used

Correct setting

Specifies the correct setting.

Faults

Specifies the faults that can occur due to an incorrect setting.

Steps to be performed when operating the machine (sewing

and equipping)

Steps to be performed for servicing, maintenance, and

installation

Steps to be performed via the software control panel

The individual steps are numbered:

1. First step

2. Second step

The sequence of the steps must always be followed.

Result of performing an operation

Change to the machine or in the display.

Important

Special attention must be paid to this point when performing a step.

Information

Additional information, e. g. on alternative operating possibilities.

Sequence

Specifies the work to be performed before or after a setting.

It is vital that this sequence is adhered to.

Reference

 A reference is provided to another place in the text.

...



Safety instructions

Operating manual 281 Version 06.0 - 05/2013 5

2 Safety instructions

This section contains basic instructions for your safety. Read the

instructions carefully before setting up, programming, maintaining,

or operating the machine. Make sure to follow the information

included in the safety instructions. Failure to do this can result in

serious injury and damage to the machine.

2.1 General safety instructions

Only authorized persons may use the machine.

Every person who works with the machine must have read the

operating manual first.

The machine may only be used as described in this manual.

The operating manual must be available at the machine's location

at all times.

Also observe the safety instructions and the operating manual for

the drive.

Observe the generally applicable safety and accident prevention

regulations and the legal regulations concerning industrial safety

and the protection of the environment.

All warnings on the machine must always be in legible condition

and may not be removed. Missing or damaged labels must be

replaced immediately.

For the following work, the machine must be disconnected from

the power supply using the main switch or by disconnecting the

power plug:

• Threading

• Replacing the needle or other sewing tools

• Leaving the workplace

• Performing maintenance work and repairs

Safety instructions

Operating manual 281 Version 06.0 - 05/20136

Inspect the machine while in use for any externally visible damage.

Interrupt your work if you notice any changes to the machine.

Report any changes to your supervisor. A damaged machine may

not be used any more.

Machines or machine parts that have reached the end of their

service life must not be used any longer. They have to be disposed

of correctly and in accordance with the applicable statutory

provisions.

The machine may only be set up by qualified specialists.

Maintenance work and repairs may only be carried out by qualified

specialists.

Safety equipment may not be removed or put out of service. If this

cannot be avoided for a repair operation, the safety equipment

must be refitted and put back into service immediately afterwards.

Work on electrical equipment may only be carried out by qualified

electrical specialists.

The connecting cable must have a power plug approved in the

specific country. The power plug may only be connected to the

power cable by a qualified electrical specialist.

Work on live components and equipment is prohibited. Exceptions

are defined in DIN VDE 0105.

Missing or faulty spare parts could impair safety and damage the

machine. Therefore only use original spare parts from the

manufacturer.

Safety instructions

Operating manual 281 Version 06.0 - 05/2013 7

2.2 Signal words and symbols used in safety

instructions

The safety instruction text is surrounded by colored bars.

Signal words specify the severity of a danger:

•Danger: Resulting in death or serious injury.

•Warning: Death or serious injury possible.

•Caution: Moderate to minor injuries are possible.

•Attention: Damage possible.

In the case of dangers to personnel, the following symbols indicate

the type of hazard:

General danger

Danger due to sharp objects

Danger due to electric shock

Danger due to crushing

Safety instructions

Operating manual 281 Version 06.0 - 05/20138

Examples of the layout of the safety instructions in the text:

Type and source of the danger

Consequences in the event of noncompliance

Measures for avoiding the danger

This is what a hazard note looks like for a hazard

that will result in serious injury or even death if not

complied with.

DANGER

Type and source of the danger

Consequences in the event of noncompliance

Measures for avoiding the danger

This is what a hazard note looks like for a hazard

that could result in moderate or minor injury if not

complied with.

CAUTION

Type and source of the danger

Consequences in the event of noncompliance

Measures for avoiding the danger

This is what a hazard note looks like for a hazard that could

result in material damage if not complied with.

ATTENTION

Type and source of the danger

Consequences in the event of noncompliance

Measures for avoiding the danger

This is what an environmental protection note looks

like for a hazard that could result in environmental

damage if not complied with.

ENVIRONMENTAL PROTECTION

Tabla de contenidos

Otros manuales de Máquina de coser de DURKOPP ADLER

DURKOPP ADLER

DURKOPP ADLER H-Type 969 Instrucciones de funcionamiento

DURKOPP ADLER

DURKOPP ADLER 275 Series Manual de funcionamiento

DURKOPP ADLER

DURKOPP ADLER 7700 Manual de usuario

DURKOPP ADLER

DURKOPP ADLER 550-12-24 Manual de lista de piezas

DURKOPP ADLER

DURKOPP ADLER 650-16 Manual de usuario

DURKOPP ADLER

DURKOPP ADLER 745-34-2 Manual de usuario

DURKOPP ADLER

DURKOPP ADLER 550-532 Manual de usuario

DURKOPP ADLER

DURKOPP ADLER 867 Manual de usuario

DURKOPP ADLER

DURKOPP ADLER 219 Manual de operación y mantenimiento

DURKOPP ADLER

DURKOPP ADLER DAC BASIC - CLASS 271 PART II V 12-2010 Manual de usuario

DURKOPP ADLER

DURKOPP ADLER M-Type Delta D867 Manual de funcionamiento

DURKOPP ADLER

DURKOPP ADLER 275 Series Guía

DURKOPP ADLER

DURKOPP ADLER 531-211 Manual de usuario

DURKOPP ADLER

DURKOPP ADLER 512/532 Manual de usuario

DURKOPP ADLER

DURKOPP ADLER DAC BASIC - CLASS 271 PART II V 12-2010 Manual de usuario

DURKOPP ADLER

DURKOPP ADLER 745-34 - Manual de usuario

DURKOPP ADLER

DURKOPP ADLER 580 - Manual de usuario

DURKOPP ADLER

DURKOPP ADLER 512-211-01 Instrucciones de funcionamiento

DURKOPP ADLER

DURKOPP ADLER 4182i-1 Manual de usuario

DURKOPP ADLER

DURKOPP ADLER 806 Instrucciones de funcionamiento

DURKOPP ADLER

DURKOPP ADLER class 743-221 Manual de usuario

DURKOPP ADLER

DURKOPP ADLER 559 - Guía del usuario

DURKOPP ADLER

DURKOPP ADLER 370 Manual de usuario

DURKOPP ADLER

DURKOPP ADLER M-Type Premium Series Manual de funcionamiento

Manuales populares de Máquina de coser de otras marcas

Riccar

Riccar RL634DE Manual de usuario

Singer

Singer 2517 Manual de usuario

Pfaff

Pfaff 3307-1 SERIES Manual de usuario

Janome

Janome Quilt Maker Pro 18 VERSA Manual de usuario

Siruba

Siruba C007JP Manual de usuario

Husqvarna Viking

Husqvarna Viking Designer SE Manual de usuario

Singer

Singer 148-5 Manual de usuario

IKEA

IKEA SY Manual de usuario

Pfaff

Pfaff 571 Manual de usuario

Singer

Singer 15-91 Manual de usuario

Brother

Brother BB370 Manual de usuario

Pegasus

Pegasus WT100 Series Manual de usuario

Reliable

Reliable 7100DB Manual de usuario

Pfaff

Pfaff 937 Manual de usuario

Singer

Singer 6038 Manual de usuario

Singer

Singer 413K Manual de usuario

Pfaff

Pfaff 1471 E1 Manual de usuario

Kenmore

Kenmore 16677 - Serger Sewing Machine Manual de usuario