Duratuf SENTRY SS2007 Manual de usuario
ASSEMBLY INSTRUCTIONS
SS2007
BASE SIZE: 2.020m x 0.685m
CHECK OUT OUR ASSEMBLY VIDEO
Let Keith and Jusn show you how to build your
Sentry shed like a professional.
When used in conjuncon with these assembly instrucons, Keith’s praccal ps and tricks will make your
assembly experience much simpler. Giving you visual guidance through secons that seem tricky on pa-
per, and helping you achieve a awless end result.
To view the video visit www.duratuf.co.nz/sentry-assembly
Note: Assembly video features a SL1520. But can be used for reference for any other Sentry model.
CONGRATULATIONS ON PURCHASING A DURATUF SENTRY SHED.
BEFORE YOU BEGIN THE ASSEMBLY PLEASE NOTE SOME IMPORTANT POINTS:
3
BEFORE YOU START:
• Read all instructions carefully
• Identify all parts and check quantities against parts list
• Select a level site
• Do not mark cladding with pencil as lead can cause corrosion to cladding
SAFETY:
• Do not attempt to build your shed in high winds
• Beware of sharp edges, recommend use of gloves
• Protect your eyes and ears
• For ease of assembly, use a friend to help
TOOLS REQUIRED:
WARRANTY REQUIREMENTS:
Following are the minimum requirements for cladding used in Sentry Sheds.
• Wash all surfaces annually using a hose and soft nylon brush.
• Within 2 km of coast – wash every 3 months as above. After a storm, wash the cladding and the gutters as soon
as possible to remove any highly corrosive salt deposits.
• Volcanic Ash Fallout – wash as soon as possible, removing fall out from roof and gutters.
• Do not allow manures, chemicals or other corrosive materials to have direct contact with cladding.
DRILL RIVETER 3.5mm DRILL BIT
HAMMER
LADDER
TAPE MEASURE 8mm HEX DRIVENAIL PUNCH
SQUARE DRILL BIT
SKILL SAW
(timber floor only)
4
SS2007 PARTS LIST
Back Wall - 1.890m 4
Side Wall - 1.850m 2
Side Wall 1 Pan - 1.850m 2
Front Wall Sheet 1 Pan - 1.850m 1
Front Wall Sheet 2 Pan - 1.850m 1
Roof - 0.770m 4
Door Sheets (Full Width) - 1.810m 2
Door Sheets 1 Pan - 1.810m 2
Door Sides - 1.810m 4
Door Jamb - 1.850m 2
Door Brace - 1.000m 4
Barge - 0.770m 2
Door Top/Bottom - 0.715m 4
Weather strip - 1.810m 1
Hardware Pack 1
Touchup Paint & Brush 1
Checked: Date:
CLADDING + FLASHING + HARDWARE
DESCRIPTION QTY DIAGRAM CHECKED
PACK 1
5
SS2007 PARTS LIST
PACK 2
TIMBER PACK
DESCRIPTION QTY DIAGRAM
Front/Back Bottom Plates - H4 (Green)
2.020 m 2
Front Top Plate - H1 (Red)
2.020 m 1
Back Top Plate - H1 (Red)
2.020 m 1
Side Wall Bottom Plates - H4 (Green)
0.685m 2
Side Wall Top Plates - H1 (Red)
0.685m 2
Ridge - 2.055m 1
Spouting - 2.055m 1
PARTS LOCATION
Top Plate Back
Side Wall Sheets
Barge Flashing
Spouting
Roof Sheets
Top Plate Side
Top Plate Front
Bottom Plate FrontBottom Plate Side
Back Wall Sheets
Front Wall Sheets
Door Jambs
Front Wall 1 Pan Sheet
QUICK OVERVIEW
1
LAY FOUNDATION
2
ASSEMBLE DOOR
3
ASSEMBLE SIDE
PANELS
8
SECURE SHED
6
Ridge
Door Sheets
Padbolt Support Hinge
Door Top/Bottom Flashing
Door Brace
4
5
ASSEMBLE FRONT
PANEL
6
ASSEMBLE WALLS
7
ASSEMBLE ROOF
FOUNDATION
SENTRY WOODEN FLOOR
• The optional Sentry kitset wooden floor is precut and designed to
be fitted into the shed after the shed is assembled.
• Assemble shed as per instructions and fit floor last.
(see page 14 for details).
CONCRETE SLAB FOR RAISED BASE PLATE SHED
To build a raised concrete slab for your shed to sit on, we recom-
mend the following:
• The raised slab size should be 15mm smaller than the base
size of the shed and at least 30mm above ground line.
• The slab should be 80mm thick in the middle and 100mm
thick around the edges.
• The slab should be laid on a solid or compacted base.
• Plastic sheeting under slab will prevent moisture coming
through from underneath.
• During construction, you may raise the bottom timber
plate to allow the wall cladding to protrude 20mm below
the bottom plate. This will stop water flowing between
the bottom plate and the concrete floor.
See note on page 9.
80mm
100mm
7.5mm
20mm
Concrete Floor
Base Plate
Wall Cladding
7
RAISED BASE PLATE OPTION
(For sheds placed on a raised concrete floor)
No doubt by now you will have decided what sort of base you are putting down.
Please read the section that applies to your situation.
If you choose to pour a concrete base you will need to decide whether you wish to raise the base plate of your shed.
This allows the cladding to protrude below the surface of the concrete and ensures a water tight pad.
See concrete pad specifications below
By choosing this option you will need to make the pad to the specification below.
ASSEMBLE DOOR
8
SELECT:
2 x 1.810m Door Sheets
2 x 1.810m Door Sheets 1 pan
4 x 0.715m Door Top/Bottom Flashings
4 x 1.810m Door Side Flashings
1 x 1.810m Weather-strip
6 x Hinges
1 x Padbolt Support Flashing
4 x 1.100m Door Brace Flashings
106 x Rivets
STEP 1:
• Lay out 1 x 1.810m Door Sheet and 1 x
1 Pan Sheet on a flat surface.
• Rivet sheets together in the centre
ensuring ends are flush with each other.
STEP 2:
• Position door side flashings and top and
bottom flashings and assemble door as
shown, ensuring narrow face of flashing
is on the front as per fig.1
• Drill and rivet as per diagram.
STEP 4:
• On the back of the door, place door braces in position
as shown in fig.4
• Ensure that the top and bottom ends of the braces
are under the door flashings as shown in fig.5 and
opposite ends of the braces overlap in the middle as
shown in fig.6.
• Rivet door brace flashings onto back of door as
shown. Where possible, rivet from front of door.
STEP 3:
• Attach hinges to door side flashing using rivets provided.
Ensure hinge is flush with back of door, and 60mm in from
each end as per fig.2.
• Using six rivets, attach padbolt support as shown in fig. 3
fig.4
fig.2
STEP 5:
• Assemble second door as above but attach weather
strip flashing to back of door side flashing using six
rivets ensuring it protrudes 20mm out from door side.
Hinges
fig.3
fig.1
fig.5
fig.6
ASSEMBLE SIDE PANELS
9
TOP PLATE
BOTTOM PLATE
1810mm 1833mm
TOP PLATE
15mm 15mm
TOP PLATE
BOTTOM PLATE
1810mm
1833mm
Second Side
Panel
BOTTOM PLATE
TOP PLATE
SELECT:
2 x 1.850 Wall Sheets
2 x 1.850 1 Pan Wall Sheets
2 x 0.685 Top Plates (Red)
2 x 0.685 Bottom Plates (Green)
32 x 30mm Galv Clouts
4 x Rivets
STEP 2:
• Place 1 x 1.850 wall sheet and 1 x Pan wall sheet on top of timber
plates, with sheets flush with each other.
• Rivet sheets together on overlaps as shown.
STEP 3:
• Nail wall sheets to the Top Plate at each end making
sure that the top of the sheets are flush with the top of
the Top Plate and the sides of the wall sheet overhang
the Top Plate by approx 15mm as shown.
• Check that the Top Plate is straight then nail along the
wall sheet to the Top Plate, two clouts per pan (see
fig. 1).
STEP 4:
• Nail the wall sheets to the Bottom Plate at each end ensuring each
side of wall sheets overhangs the end of Bottom Plate by 15mm.
Check that the distance between the Top and Bottom Plates is
correct. (As per diagram in step 1)
• Check that the Bottom Plate is straight then nail the wall sheets to
the Bottom Plate, two clouts per pan (see fig. 1).
Repeat with second side panel ensuring Top Plate is positioned in
the OPPOSITE direction to the first side panel, as shown.
fig.1
RIB
PAN
CLOUT
TIMBER PLATE
Std Shed — Bottom Plate will protrude below wall
sheet by approximately 10mm.
Raised base plate shed — Wall sheet will protrude
below the Bottom Plate by 20mm.
IMPORTANT—IF YOU CHOOSE TO RAISE YOUR TIMBER
BASE PLATE –READ THE FOLLOWING;
For sheds with Raised Base Plate option only (see page 6), deduct
30mm from measurement shown between Top and Bottom Plates on
all wall panels, so cladding protrudes 20mm below bottom plate.
TOP PLATE
BOTTOM PLATE
15mm 15mm
1810mm 1833mm
15mm
RIVET
RIVET
STEP 1:
• Lay out 1 x Top plate and 1 x Bottom plate on a flat surface as shown
(corner cut-outs to face outwards). Measurements between Top and
Bottom plates are critical to ensure wall panels fit together.
BOTTOM PLATE
TOP PLATE
TOP PLATE
BOTTOM PLATE
1834mm 1834mm
TOP PLATE
15mm 15mm
10
BOTTOM PLATE
15mm 15mm
1834mm 1834mm
TOP PLATE
ASSEMBLE BACK PANEL
SELECT:
4 x 1.890m Wall Sheets
1 x 2.020 m Top Plate (Red)
1 x 2.020 m Bottom Plate (Green)
48 x 30mm Galv Clouts
6 x Rivets
STEP 1:
• Lay out 1 x Top Plate and 1 x Bottom Plate on a
flat surface as shown (corner cutouts to face in-
wards).
STEP 2:
• Place 4 x 1.890 m wall sheets on top of timber
Plates with bottom of sheets flush with each oth-
er.
• Rivet the sheets together on overlaps as shown.
STEP 3:
• Nail the wall sheets to the Top Plate at each end making sure
that the top of the sheets are flush with the top of the Top
Plate and that the sides of the wall sheets overhang the Top
Plate by 15mm as shown.
• Check that the Top Plate is straight then nail wall sheets to
the Top Plate, using two clouts per pan.
STEP 4:
• Nail the wall sheets to the Bottom Plate at each end,
ensuring that each side of the wall sheets overhangs the
Bottom Plate by 15mm and that the distance between
the Top and Bottom Plates is correct. (As shown)
• Check that the Bottom Plate is straight then nail
wall sheets to the Bottom Plate, using two clouts per pan.
Std Shed — Bottom Plate will protrude below wall sheet by
approximately 10mm.
Raised base plate shed — Wall sheet will protrude below
the Bottom Plate by 20mm.
IMPORTANT—IF YOU CHOOSE TO RAISE YOUR TIMBER
BASE PLATE –READ THE FOLLOWING;
For sheds with Raised Base Plate option only (see page 57, deduct
30mm from measurement shown between Top and Bottom Plates on
all wall panels, so cladding protrudes 20mm below bottom plate.
Tabla de contenidos
Otros manuales de Almacenamiento al aire libre de Duratuf
Duratuf
Duratuf PL44 Manual de usuario
Duratuf
Duratuf GL57 Manual de usuario
Duratuf
Duratuf Paihia Manual de usuario
Duratuf
Duratuf SL2515 Manual de usuario
Duratuf
Duratuf SG2525 Manual de usuario
Duratuf
Duratuf SG2020 Manual de usuario
Duratuf
Duratuf PG98 Manual de usuario
Duratuf
Duratuf MK4B Manual de usuario
Duratuf
Duratuf PG88 Manual de usuario
Duratuf
Duratuf Guardian Sheds GS73 Manual de usuario
Duratuf
Duratuf Otago Manual de usuario
Duratuf
Duratuf PS42 Manual de usuario
Duratuf
Duratuf Sentry Shed SL1507 Manual de usuario
Duratuf
Duratuf GL95 Manual de usuario
Duratuf
Duratuf MK4C Manual de usuario
Duratuf
Duratuf Garrison Sheds PL64 Manual de usuario
Duratuf
Duratuf GG97 Manual de usuario
Duratuf
Duratuf MK4A Manual de usuario
Duratuf
Duratuf Kiwi MK1 Manual de usuario
Duratuf
Duratuf SL1520 Manual de usuario
Manuales populares de Almacenamiento al aire libre de otras marcas
rollaway container
rollaway container ARPCA24 Manual de usuario
X-METAL
X-METAL 4065 Manual de usuario
Outdoor Life Products
Outdoor Life Products FP2030 F Manual de usuario
Royalcraft
Royalcraft Faro 295L Storage Box Manual de usuario
Riverlea
Riverlea Duratuf KIWI KS3 Manual de usuario
OLT
OLT GS84D-FJ-Plywood Manual de usuario
