Duratrax Mini Quake Instrucciones de instalación y funcionamiento

Warranty

• DuraTrax will warranty this kit for 90 days after the purchase date from defects in materials or workmanship.DuraTrax will either repair

or replace, at no charge, the incorrectly made part.

• Make sure you save the receipt or invoice you were given when you purchased your model. It is your proof of purchase and we must

see it before we can honor the warranty.

• To return your Mini Quake for repairs covered under warranty you should send your model to:

Hobby Services

3002 N. Apollo Drive Suite 1

Champaign, Illinois 61822

Attn: Service Department

Phone: (217) 398-0007 9:00 am-5:00 pm Central Time M-F

E-mail:

hobbyservices@hobbico.com

If the buyer is not prepared to accept the liability associated with the use of this product, the buyer is advised to return this

kit immediately in new and unused condition to the place of purchase.

READ THROUGH THIS MANUAL BEFORE STARTING CONSTRUCTION. IT CONTAINS IMPORTANT

INSTRUCTIONS AND WARNINGS CONCERNING THE ASSEMBLY AND USE OF THIS MODEL.

ASSEMBLY AND OPERATION MANUAL

Length: 9.5" [240mm]

Width: 7.4" [185mm]

Height: 4.7" [120mm]

Weight: 25 oz [725g]

Ground Clearance: 1.25" [32mm]

Radio: 2-Channel

™

Technical Support Information

For technical assistance, contact:

DuraTrax Product Support

3002 N. Apollo Drive, Suite 1

Champaign, IL 61822

(217) 398-8970, Ext. 5

carsuppor[email protected]

INTRODUCTION................................................................2

IMPORTANT SAFETY PRECAUTIONS............................2

HELPFUL HINTS...............................................................2

STRESS TECH PARTS......................................................2

REPAIR SERVICE .............................................................3

SPECIFICATION AND DESCRIPTION CHANGES..........3

FINISHING THE MINI QUAKE...........................................3

ELECTRONIC SPEED CONTROL SET-UP......................4

ASSEMBLY GUIDE ...........................................................5

MAINTENANCE TIPS ......................................Back Cover

TUNING............................................................Back Cover

Thank you for purchasing the DuraTrax Mini Quake. This

manual contains the instruction you need to build, operate and

maintain your new electric R/C vehicle.Read over this manual

thoroughly before building or operating the Mini Quake.

When the safety precautions are followed, the Mini Quake

will provide years of enjoyment.Use care and good sense at

all times when operating this radio controlled vehicle.Failure

to use this vehicle in a safe, sensible manner can result in

injury or damage to property.You and you alone must insure

that the instructions are carefully followed and all safety

precautions are obeyed.

• Do not operate the Mini Quake near people. Spectators

should be behind the driver or at a safe distance away

from the vehicle.

• Make sure to read the instructions before charging

the battery.

• Do not leave the charger unattended during charging. If

the battery or charger become hot at any time,

disconnect the battery from the charger immediately!

Failure to do so may cause permanent damage to the

charger and battery and may cause bodily harm.

• Do not cover the charger during charging. This may

cause the charger to overheat.

• Do not allow the electronic speed control (ESC) or radio

equipment to come into contact with moisture. Water

can cause the electronics to short out and cause

permanent damage.

• Always turn on the transmitter before turning on the

electronic speed control.

• Before turning on your radio, check to make sure that

no one else is running on the same frequency as your

Mini Quake.

• Avoid working over a deep pile carpet. If you drop a small

part or screw, it will be difficult to find.

• Place a mat or towel over your work surface.This will prevent

parts from rolling off and will protect the work surface.

• Test fit all parts before attaching them permanently.

We have engineered the Mini Quake to take the rough and

tumble abuse that makes R/C fun. We are so confident of

the quality and durability of the Stress-Tech plastic parts

that we will replace any Stress-Tech plastic part you break

during the first 12 months you own the vehicle. Just send in

the part to us and we will send you a FREE replacement.

Please see the Mini Quake parts list for the items covered

under the Stress-Tech guarantee.

To receive your free replacement part, please send the

following to the Hobby Services address listed on the front

cover of this manual.

❏1.The broken part must be included.

❏2.The part number and description of the broken part.

❏3. Dated copy of your invoice or purchase receipt.

❏4.Your name, phone number and shipping address.

STRESS-TECH™PARTS GUARANTEE

HELPFUL HINTS

SAFETY PRECAUTIONS

INTRODUCTION

TABLE OF CONTENTS

Repair service is available anytime.

• After the 90 day warranty, you can still have your Mini

Quake repaired for a small charge by the experts at

DuraTrax’s authorized repair facility, Hobby Services, at

the address listed on the front cover of this manual.

• To speed up the repair process, please follow the

instruction listed below.

❏1. Under most circumstances return the ENTIRE system:

vehicle and radio. The exception would be sending in a

Stress-Tech part. See the instruction under the Stress-

Tech Guarantee.

❏2. Make sure the transmitter is turned off and all of the

batteries are removed.

❏3. Send written instructions which include: a list of all

items returned, a THOROUGH explanation of the problem,

the service needed and your phone number during the day.

If you expect the repair to be covered under warranty, be

sure to include a proof of date of purchase (your store

receipt or purchase invoice).

❏4. Also be sure to include your full return address.

All pictures, descriptions and specifications found in this

instruction manual are subject to change without notice.

DuraTrax maintains no responsibility for inadvertent errors

in this manual.

❏1. Charge the included 6-cell battery on the included wall

charger.Connect the 6-cell NiCd battery to the connector on

the wall charger. Plug the wall charger into a standard

household 110V power outlet. Check to make sure that the

red LED on the wall charger is lit. If the LED does not light,

check to make sure the battery is properly connected to the

charger.The battery should not be left on the charger longer

than 3 hours when fully discharged.If at any time during the

charge the battery becomes warm to the touch, it should be

removed immediately to prevent damage to either the

battery or the charger.

❏2. Install the transmitter antenna by screwing it into the

hole on the top of the transmitter. Give the top of the

antenna a light tug to make sure that it is properly secured

to the transmitter.

❏3. Slide the battery door on

the bottom of the transmitter

open. Install eight (8) “AA”

batteries into the transmitter in

the configuration molded into

the plastic on the battery holder.

Re-install the battery door.

❏4.Turn on the transmitter using the on/off switch (see step

#3). The red light on the transmitter should light up. If there

is no light on, turn the transmitter off and check to ensure

that the batteries are making contact with the metal contacts

in the battery holder. Make sure the batteries are installed

correctly.Turn the transmitter on and check for the red light.

If the red light appears, turn off the transmitter.If the red light

blinks, the batteries are low and should be replaced.

FINISHING THE MINI QUAKE

SPECIFICATION & DESCRIPTION CHANGES

REPAIR SERVICE

❏5. Straighten the receiver antenna. Run the receiver

antenna wire through the included antenna tube. DO NOT

CUT OR COIL THE ANTENNA WIRE. Press fit the antenna

tube into the antenna mount hole. TIP: Run the antenna

wire through your finger to straighten out the kinks before

running through the antenna tube. Also applying a small

amount of soap and water to the antenna wire will help

lubricate the wire for threading into the antenna tube.

❏6. Remove the body clips from the battery holder and

insert the charged 6-cell battery pack into the chassis.

❏7. Re-install the battery clips onto the battery holder.

❏8. The transmitter features an adjustable steering rate

knob labeled “D/R” on the top of the transmitter. Turning it

fully clockwise will give you the greatest amount of steering

travel.Turning it counter clockwise will reduce the amount of

steering travel.

❏9.The servo reversing switches are pre-set at the factory, but

should be double-checked before running your Mini Quake.

❏A. Turn the transmitter on, then the receiver. NOTE:

Always turn your transmitter on first. Gently pull back

on the throttle trigger, the Mini Quake should slowly move

forward. If the Mini Quake goes in reverse, move the

throttle reversing switch on the transmitter to the opposite

position (refer to page 3 for location of the reversing

switches).After doing this, the throttle trim knob may need

to be adjusted to find the throttle’s neutral point.

❏B.Now, check that the steering reversing switch is set

properly. With the transmitter wheel facing you and the

truck facing away from you, turn the transmitter steering

wheel to the right.The wheels of the truck should turn so

that when the truck moves it will turn to the right.If it turns

to the left, the steering reversing switch needs to be

moved to the opposite position. After reversing the

steering, the steering trim on the transmitter may need to

be adjusted to enter the steering of the truck.

❏10. Decal the body as desired and install it onto the

chassis, securing it in place with the four included body clips.

❏11. Congratulations!You are ready to race!

Center the trim knobs on the transmitter.

❏1. Connect the battery pack to the ESC, turn on the Tx,

then the ESC.

❏2. Press and hold the “set” button until both LEDs are

flashing, then release the button.

❏3.NEUTRAL POINT:Leave the throttle trigger in the neutral

position.Press the setup button once;the green LED will flash.

❏4.FULL THROTTLE: Move the throttle trigger to full

throttle and press the button once until the red LED

illuminates (motor will not operate in set up mode).

❏5.FULL REVERSE: Move the throttle trigger to full reverse

and press the button once – the red LED will stop flashing.

Release the throttle trigger; the ESC is now ready to operate

with your system.If the motor operates in reverse when applying

forward throttle, the throttle reversing switch on the Tx must be

moved to the opposite position.

ELECTRONIC SPEED CONTROL SET UP

ASSEMBLY GUIDE

Tabla de contenidos

Otros manuales de Coche de juguete motorizado de Duratrax

Duratrax

Duratrax Nitro Evader BX Instrucciones de instalación y funcionamiento

Duratrax

Duratrax Overdrive ST Instrucciones de instalación y funcionamiento

Duratrax

Duratrax DXR500 Manual de usuario

Duratrax

Duratrax MAXIMUM MT Instrucciones de instalación y funcionamiento

Duratrax

Duratrax Delphi Indy Car Instrucciones de instalación y funcionamiento

Duratrax

Duratrax 835E Manual de usuario

Duratrax

Duratrax Nitro Evader ST DTXD62 Manual de usuario

Duratrax

Duratrax WarHead EVO Manual de usuario

Duratrax

Duratrax VW Baja Bug Manual de usuario

Duratrax

Duratrax Vendetta Instrucciones de instalación y funcionamiento

Duratrax

Duratrax Evader EXT2 Instrucciones de instalación y funcionamiento

Duratrax

Duratrax Maximum MT Pro Instrucciones de instalación y funcionamiento

Duratrax

Duratrax Evader ST Pro Instrucciones de instalación y funcionamiento

Duratrax

Duratrax DTXC0028 Instrucciones de instalación y funcionamiento

Duratrax

Duratrax Vendetta SC Instrucciones de instalación y funcionamiento

Duratrax

Duratrax Vendetta Instrucciones de instalación y funcionamiento

Duratrax

Duratrax Evader BX Instrucciones de instalación y funcionamiento

Duratrax

Duratrax Evader BX Pro Manual de usuario

Duratrax

Duratrax Evader EXB Instrucciones de instalación y funcionamiento

Duratrax

Duratrax 835B Manual de usuario

Duratrax

Duratrax Street Force GP Instrucciones de instalación y funcionamiento

Duratrax

Duratrax Raze ST Instrucciones de instalación y funcionamiento

Duratrax

Duratrax Thunder Quake Instrucciones de instalación y funcionamiento

Duratrax

Duratrax Street force GP2 Instrucciones de instalación y funcionamiento

Manuales populares de Coche de juguete motorizado de otras marcas

Eduard

Eduard Humber Scout Car Mk.I exterior Manual de usuario

Traxxas

Traxxas 4995X Manual de usuario

Jamara

Jamara VW T1 Bus Manual de usuario

REVELL

REVELL 68 CHEVY CHEVELLE SS 396 Manual de usuario

Schumacher

Schumacher Pro Cat Manual de usuario

Tamiya

Tamiya TT-01 TYPE E Manual de usuario

Eduard

Eduard Krupp Protze 6x4 1/48 Manual de usuario

New Bright

New Bright 61072UEP Manual de usuario

Team Durango

Team Durango DEX410v5 Manual de usuario

Jamara

Jamara Mercedes Actros Muldenkipper 2,4 GHz Manual de usuario

PLAYMOBIL

PLAYMOBIL 9536 Manual de usuario

Atomic

Atomic BZ3 Manual de usuario

Aiyaplay

Aiyaplay 370-290V00 Manual de usuario

Power Wheels

Power Wheels GRJ53 Manual de usuario

ZEROTRIBE

ZEROTRIBE Zetricks ZT1144 Manual de usuario

INJUSA

INJUSA 412 Manual de usuario

Maverick

Maverick MSC-30BR-WP Manual de usuario

Land of B.

Land of B. Rollin' Riders Manual de usuario