Dual WCP165GH Instrucciones de funcionamiento
WCP165GH
MGR11BT AM/FM Gauge Hole Receiver
and WSM651 6.5" Car Audio Speakers
INSTALLATION/OWNER'S MANUAL
Rear Inputs
2
WCP165GH INSTALLATION
Mounting
Please read entire manual before installation.
Before You Start
• Disconnect negative battery terminal. Consult a qualified technician for instructions.
• Avoid installing the unit where it would be subject to high temperatures, such as from
direct sunlight, or where it would be subject to dust, dirt or excessive vibration.
Getting Started
• Once a suitable location has been determined, drill the hole and secure the stereo
using the metal mounting bracket. If the bracket needs to be shortened, remove the
appropriate number of breakaway segments using a pair of pliers.
Fuse:
When replacing the fuse, make sure
new fuse is the correct type and
amperage. Using an incorrect fuse
could damage the radio.
Tip:
When a suitable ground wire is
not present in the vehicle wiring
harness, connect the black ground
wire to the vehicle chassis.
Break Lines
Color Connection
Red 12V Ignition / Accessory
Black Ground
Blue Remote Turn-on B (+)
Grey Right Front (+)
Grey/Black Right Front (-)
White Left Front (+)
White/Black Left Front (-)
Violet Right Rear (+)
Violet/Black Right Rear (-)
Green Left Rear (+)
Green/Black Left Rear (-)
3
WCP165GH INSTALLATION
Mounting the Radio
1. Choose a mounting location on the dash board or instrument panel that will
allow room behind to run radio cables to the power source. Consider how you will use
the AUX IN, LINE OUT and USB connectors and route the appropriate extension cables
to an accessible area.
2. Cut a hole in the dash board using the template provided in the back of this manual. At
least 3 3/4” depth is needed to mount the radio.
IMPORTANT! Do not mount this unit where it can be submerged in water.
3. Slide the included spring washers (B) over the screw posts (A) and attach the screw
posts to the back of the radio.
4. Place the radio in front of the dashboard opening so the wiring can be brought through
the opening.
5. After completing the wiring connections, turn the radio on to confirm operation (vehicle
accessory switch must be on). If the radio does not operate, recheck all wiring until the
problem is corrected. Once proper operation is achieved, turn the accessory switch off
and proceed with final mounting of the radio. Refer to the “Wiring Diagram” on page 5.
NOTE: Before final installation, test the wiring connections to make sure the unit is
connected properly and the system works.
6. Insert the radio into the mounting hole.
7. Place the “U” bracket (C) over the screw posts and secure the radio to the dash using
the included hex nuts (D). If necessary, cut the score marks (E) on either side of the
mounting bracket to custom fit the bracket length for your application. See Figure A.
Installation
A
C
D
E
B
3 Inch Hole
Installation
4
WCP165GH OPERATION
Wiring
FUSE
ANT
USB
AUX
REAR LINE OUT
STEERING WHEEL
PHONE JACK(Ø3.5)
2P RCA CABLE(YELLOW)
2P RCA CABLE(GRAY)
ANTØ3(BLACK)
USBØ5(BLACK)
RED MOLDNNG
WHITE MOLDING
RED MOLDNNG
WHITE MOLDING
5
WCP165GH OPERATION
Control Locations
12
4
3
5
6
7
8
9
10
11
Preset 6 / Folder Up
Display
Mute
Preset 5 / Folder Down
Preset 4 / Play / Pause
Preset 1 / Repeat
Band / Go Back
Tune / Track Down
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Mode
Volume Up
Power
Select
Tune / Track Up
Volume Down
Audio / Menu
Preset 3 / Intro
Preset 2 / Random
3
5
15
13
14
16
17
12
1
2
4
6
7
8
9
10
Select
Volume Up
Volume Down
Mode
Audio / Menu
1
2
3
4
5
6
7
8
9
10
Power / Mute
Band / Go Back / Display
Tune Down
Tune Up
Play / Pause / Presets
6
WCP165GH OPERATION
Press to turn the unit on. Press and hold to turn the
unit off.
Press MODE to select between AM/FM, auxiliary, USB and
Bluetooth. Modes of operation are shown in the display.
NOTE: USB mode will not appear unless a USB device is
connected.
The MGR11BT offers rear RCA auxiliary input ports for
connecting an audio device, MP3 player, etc. Press MODE to
select auxiliary input mode.
Adjust volume using the VOL+ or VOL- buttons.
Press DISP to select between clock and different types of
information, such as radio frequency or MP song
information.
Press and hold the PLAY/PAUSE button for more than 10
seconds to reset the unit to default factory settings.
Press and hold AUDIO/MENU for more than 3 seconds to
access the setup menu. Press AUDIO/MENU momentarily
to select between the menu functions and use the VOL+ or
VOL- buttons to adjust or activate the desired function.
Power On/Off
Mode
Auxiliary Inputs
Volume
Display
Reset
Setup Menu
General Operation
7
WCP165GH OPERATION
General Operation - Setup Menu
Menu Function Options Action
Auto Station
Store AUTO STORE Press SELECT to seek and save 6 strong stations in the
current band. (Tuner mode only)
Local/Distance
Tuning
LOCAL OFF Activates distance tuning (Tuner mode only).
LOCAL ON Activates local tuning for strong station reception only (Tuner
mode only).
Tuner
Frequency
Spacing
FREQ USA Programs the unit to USA tuner spacing.
(200kHz for FM and 10kHz for AM). (Tuner mode only)
FREQ EURO Programs the unit to European tuner spacing.
(50kHz for FM and 9kHz for AM). (Tuner mode only)
Beep
Confirmation
BEEP OFF Disables the confirmation beep.
BEEP ON Enables the confirmation beep.
Programmable
Turn On Volume PRO-VOL # Programs unit to always turn on at a specific volume
(default is OFF). Any volume level 1-40 can be selected.
Low Battery
L-BATT ON
Battery Voltage drops(10.8V+/-0.03V)a Beep will sound.(default)
L-BATT OFF
Battery Voltage drops(10.8V+/-0.03V)a Beep will not sound.
8
WCP165GH OPERATION
Press AUDIO/MENU momentarily to select between Bass,
Middle, Treble, Balance, Fader, Loudness, EQ and Source
Volume Level.
Press AUDIO/MENU until BASS appears then press VOL+ or
VOL- to adjust ( -7 minimum / +7 maximum).
Press AUDIO/MENU until TREBLE appears then press VOL+
or VOL- to adjust ( -7 minimum / +7 maximum).
Press AUDIO/MENU until BAL appears then press VOL+ or
VOL- to adjust (BAL LEFT 10 - BAL RIGHT 10).
BAL EVEN represents equal balance.
Press AUDIO/MENU until FADER appears then press VOL+
or VOL- to adjust (FADER FRONT 10 - FADER REAR 10).
FADER EVEN represents equal fader.
Press EQ, then then press VOL+ or VOL- to cycle through
the following equalization curves: EQ-OFF, Pop, Jazz,
Classic, Beat or Rock. Any manual adjustment to the Bass
or Treble settings are automatically saved as USER.
Press AUDIO/MENU until LOUD appears then press VOL+ or
VOL- to turn the Loudness feature ON or OFF.
Select between STEREO or MONO in FM Radio mode.
Audio
Bass
Treble
Balance
Fader
EQ
Loudness
Stereo
BASS TREBLE BALANCE FADER LOUD EQ STEREO
General Operation
9
WCP165GH OPERATION
Seek Tuning
Manual Tuning
Band
Storing
Preset Stations
(IR Remote Control Only)
Recalling
Preset Stations
Manual Tuning
Band
Press TUNE
nn
or TUNE
ll
for more than one second
to seek to the next strong station.
Press TUNE
nn
or TUNE
ll
momentarily to change
radio frequency up or down one step at a time. Press and
hold to advance quickly.
Press BAND to select between FM1, FM2, FM3, AM1 and
AM2 bands. Up to six presets can be programmed for each
band, enabling up to 18 FM stations and 12 AM stations to
be stored in memory.
Select the desired band and station. Hold the P button,
press the volume up/down buttons until the desired preset
number is highlighted, then press SELECT to store the
preset.
Press the Pbutton to cycle through the 1-6 presets in the
current band.
Press TUNE
nn
or TUNE
ll
momentarily to seek the
next weather band station.
Press BAND to select weather band (WB).
AM/FM Tuner Operation
Weather Band Operation
10
WCP165GH OPERATION
USB Operation
To play MP3 files from most USB mass storage devices, line
up the USB connector and insert the USB device into the
MGR11BT's USB port.
When a USB device is first connected, “USB READ” will
appear in the display and playback will begin momentarily.
Depending on the number of files and folders, it may take
several seconds for the device to begin playing. If no valid
MP3 files are detected, “NO FILE” will be displayed and the
last mode will be resumed.
Press TRACK
ll
to skip to the beginning of the next
track. Press TRACK
nn
to return to the beginning of the
current track. Pressing TRACK
nn
again skips to the
beginning of the previous track.
Press and hold TRACK
ll
or TRACK
nn
to fast
forward or reverse a track.
Press
l
/
II
to temporarily stop USB playback.
Press
l
/
II
again to resume playback.
Press SELECT to enter the track search mode. A list of all
the files from the USB device will be displayed.
Press SELECT again. "USB SEARCH" will be displayed
momentarily, then the track number will blink.
Use the VOL+ or VOL- buttons to navigate, then press
SELECT to choose the desired track.
Press BACK to exit USB Search Mode.
Connecting a USB Device
(sold separately)
Playing Music
Track Select
Fast Forward and
Reverse
Pause
File Search
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Receptor estéreo de Dual
Dual
Dual XDMA5280 Instrucciones de funcionamiento
Dual
Dual CR 1730 Manual de usuario
Dual
Dual XDVD8181 Instrucciones de funcionamiento
Dual
Dual XDM280BT Instrucciones de funcionamiento
Dual
Dual XDM27BT Instrucciones de funcionamiento
Dual
Dual DC207BT Instrucciones de funcionamiento
Dual
Dual CR 1730 Manual de usuario
Manuales populares de Receptor estéreo de otras marcas
Pioneer
Pioneer SX-1000TA Manual de usuario
Yamaha
Yamaha MusicCast TSR-5B3D Manual de usuario
Sony
Sony STR-DE335 - Fm Stereo/fm-am Receiver Manual de usuario
Sony
Sony STR-DG500 - Multi Channel Av Receiver Manual de usuario
Panasonic
Panasonic AJSD955B - DVCPRO50 STUDIO DECK Manual de usuario
Pioneer
Pioneer SX-838 Manual de usuario