Dual MGH17BT Instrucciones de funcionamiento
INSTALLATION/OWNER'S MANUAL
AM/FM Gauge Hole Receiver
MGH17BT
Front and Rear Inputs
2
MGH17BT INSTALLATION
Mounting
Please read entire manual before installation.
Before You Start
• Disconnect negative battery terminal. Consult a qualified technician for instructions.
• Avoid installing the unit where it would be subject to high temperatures, such as from
direct sunlight, or where it would be subject to dust, dirt or excessive vibration.
Getting Started
• Once a suitable location has been determined, drill the hole and secure the stereo
using the metal mounting bracket. If the bracket needs to be shortened, remove the
appropriate number of breakaway segments using a pair of pliers.
Fuse:
When replacing the fuse, make sure
new fuse is the correct type and
amperage. Using an incorrect fuse
could damage the radio.
Tip:
When a suitable ground wire is
not present in the vehicle wiring
harness, connect the black ground
wire to the vehicle chassis.
Break Lines
Color Connection
Red 12V Ignition / Accessory
Black Ground
Blue Remote Turn-on B (+)
Grey Right Front (+)
Grey/Black Right Front (-)
White Left Front (+)
White/Black Left Front (-)
Violet Right Rear (+)
Violet/Black Right Rear (-)
Green Left Rear (+)
Green/Black Left Rear (-)
Yellow Camera Input (RCA)
3
MGH17BT INSTALLATION
Mounting the Radio
1. Choose a mounting location on the dash board or instrument panel that will
allow room behind to run radio cables to the power source. Consider how you will use
the AUX IN, LINE OUT and USB connectors and route the appropriate extension cables
to an accessible area.
2. Cut a hole in the dash board using the template provided in the back of this manual. At
least 3 3/4” depth is needed to mount the radio.
IMPORTANT! Do not mount this unit where it can be submerged in water.
3. Slide the included spring washers (B) over the screw posts (A) and attach the screw
posts to the back of the radio.
4. Place the radio in front of the dashboard opening so the wiring can be brought through
the opening.
5. After completing the wiring connections, turn the radio on to confirm operation (vehicle
accessory switch must be on). If the radio does not operate, recheck all wiring until the
problem is corrected. Once proper operation is achieved, turn the accessory switch off
and proceed with final mounting of the radio. Refer to the “Wiring Diagram” on page 5.
NOTE: Before final installation, test the wiring connections to make sure the unit is con-
nected properly and the system works.
6. Insert the radio into the mounting hole.
7. Place the “U” bracket (C) over the screw posts and secure the radio to the dash using
the included hex nuts (D). If necessary, cut the score marks (E) on either side of the
mounting bracket to custom fit the bracket length for your application. See Figure A.
Installation
A
C
D
E
B
3 Inch Hole
Installation
4
MGH17BT OPERATION
Wiring
FUSE
ANT
USB
AUX
REAR LINE OUT
STEERING WHEEL
PHONE JACK(Ø3.5)
2P RCA CABLE(YELLOW)
2P RCA CABLE(GRAY)
ANTØ3(BLACK)
USBØ5(BLACK)
RED MOLDNNG
WHITE MOLDING
RED MOLDNNG
WHITE MOLDING
5
MGH17BT OPERATION
Control Locations
12
4
3
5
6
7
8
9
10
11
Preset 6 / Folder Up
Display
Mute
Preset 5 / Folder Down
Preset 4 / Play / Pause
Preset 1 / Repeat
Band / Go Back
Tune / Track Down
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Mode
Volume Up
Power
Select
Tune / Track Up
Volume Down
Audio / Menu
Preset 3 / Intro
Preset 2 / Random
4
6
15
13
14
16
17
12
1
2
3
5
7
8
9
10
11 Select
Volume Up
Volume Down
Mode
Audio / Menu
1
2
3
4
5
6
7
8
9
10
11
Power
Mute
Band / Go Back / Display
Tune Down
Tune Up
Play / Pause / Presets
6
MGH17BT OPERATION
Press to turn the unit on. Press and hold to turn the
unit off.
Press MODE to select between AM/FM, auxiliary, USB and
Bluetooth. Modes of operation are shown in the display.
NOTE: USB mode will not appear unless a USB device is
connected.
The MGH17BT offers rear RCA auxiliary input ports for
connecting an audio device, MP3 player, etc. Press MODE to
select auxiliary input mode.
Adjust volume using the VOL+ or VOL- buttons.
Press DISP to select between clock and different types of
information, such as radio frequency or MP song
information.
If abnormal operation occurs, press MENU and TUNE
nn
for three seconds to reset the unit to default factory settings.
Press and hold AUDIO/MENU for more than 3 seconds to
access the setup menu. Press AUDIO/MENU momentarily
to select between the menu functions and use the VOL+ or
VOL- buttons to adjust or activate the desired function.
Power On/Off
Mode
Auxiliary Inputs
Volume
Display
Reset
Setup Menu
General Operation
7
MGH17BT OPERATION
General Operation - Setup Menu
Menu Function Options Action
Auto Station
Store AUTO STORE Press SELECT to seek and save 6 strong stations in the
current band. (Tuner mode only)
Local/Distance
Tuning
LOCAL OFF Activates distance tuning (Tuner mode only).
LOCAL ON Activates local tuning for strong station reception only (Tuner
mode only).
Tuner
Frequency
Spacing
FREQ USA Programs the unit to USA tuner spacing.
(200kHz for FM and 10kHz for AM). (Tuner mode only)
FREQ EURO Programs the unit to European tuner spacing.
(50kHz for FM and 9kHz for AM). (Tuner mode only)
Selectable iPod
Control
IPOD FULL Programs the head unit to advanced control of the iPod/
iPhone device.
IPOD BASIC
Programs the head unit to manual control of the iPod/iPhone
device and allows music to be controlled from the iPod/
iPhone device.
Loudness LOUD OFF Deactivates the Loudness feature, which increases bass and
treble levels at low volume.
LOUD ON Activates the Loudness feature.
Beep
Confirmation
BEEP OFF Disables the confirmation beep.
BEEP ON Enables the confirmation beep.
Programmable
Turn On Volume PRO-VOL # Programs unit to always turn on at a specific volume
(default is OFF). Any volume level 1-46 can be selected.
Power on
Message
MESSAGE OFF Disables power on message. (example: GOOD MORNING)
MESSAGE ON Enables power on message to be displayed.
Scrolling
Option
SCROLL 15 S Programs unit to scroll information once every 15 seconds
(default).
SCROLL ONCE Programs unit to scroll once, then show the first 10
characters on display.
SCROLL ON Programs unit to scroll continuously.
SCROLL OFF Programs unit to show the first 10 characters on the display.
Illumination
Dimmer
DIMMER HIGH Programs unit to the brightest illumination level.
DIMMER MED Programs unit to the middle illumination level.
DIMMER LOW Programs unit to the dimmest illumination level.
Demonstration
Mode
DEMO OFF Disables the demonstration mode.
DEMO ON Enables the demonstration message.
8
MGH17BT OPERATION
Press AUDIO/MENU momentarily to select between Bass,
Middle, Treble, Balance, Fader, Loudness, EQ and
Stereo/Mono
Press AUDIO/MENU until BASS appears then press VOL+ or
VOL- to adjust ( -6 minimum / +6 maximum).
Press AUDIO/MENU until MIDDLE appears then press VOL+
or VOL- to adjust ( -6 minimum / +6 maximum).
Press AUDIO/MENU until TREBLE appears then press VOL+
or VOL- to adjust ( -6 minimum / +6 maximum).
Press AUDIO/MENU until BAL appears then press VOL+ or
VOL- to adjust (BAL LEFT 12 - BAL RIGHT 12).
BAL EVEN represents equal balance.
Press AUDIO/MENU until FADER appears then press VOL+
or VOL- to adjust (FADER FRONT 12 - FADER REAR 12).
FADER EVEN represents equal fader.
Press AUDIO/MENU until LOUD appears then press VOL+ or
VOL- to turn the Loudness feature ON or OFF.
Press EQ, then then press VOL+ or VOL- to cycle through
the following equalization curves: USER, ROCK, BEAT,
CLASSIC, JAZZ, POP or FLAT. Any manual adjustment to the
Bass or Treble settings are automatically saved as USER.
The source volume level control allows a gain adjustment
for each audio source. Set the source volume level for each
mode, depending on the relative volume of each audio
source.
To set the source volume level, press AUDIO/MENU until
SRC LEVEL appears. After one second, the current mode
will appear on the display. Press VOL+ or VOL- to adjust
the audio level of the current source (-6 minimum/+6
maximum).
Note: Only the current mode will be available for
adjustment. To adjust another mode of operation, press
MODE until the desired mode is selected, then set the
source volume level for that mode.
Audio
Bass
Middle
Treble
Balance
Fader
Loudness
EQ
Source Volume Level
General Operation
BASS TREBLE BALANCE FADER LOUD EQ STEREO / MONO
9
MGH17BT OPERATION
Seek Tuning
Manual Tuning
Band
Storing
Preset Stations
Recalling
Preset Stations
Press TUNE
nn
or TUNE
ll
for more than one second
to seek to the next strong station.
Press TUNE
nn
or TUNE
ll
momentarily to change
radio frequency up or down one step at a time. Press and
hold to advance quickly.
Press BAND to select between FM1, FM2, FM3, AM1 and
AM2 bands. Up to six presets can be programmed for each
band, enabling up to 18 FM stations and 12 AM stations to
Select the desired band and station. Using the remote
control, press and hold the preset number (1-6) until that
preset is shown to the right of the selected station.
Press the Pbutton to cycle through the 1-6 presets in the
current band.
AM/FM Tuner Operation
10
MGH17BT OPERATION
USB Operation
To play MP3 files from most USB mass storage devices, line
up the USB connector and insert the USB device into the
MGH17BT's USB port.
When a USB device is first connected, “USB READ” will
appear in the display and playback will begin momentarily.
Depending on the number of files and folders, it may take
several seconds for the device to begin playing. If no valid
MP3 files are detected, “NO FILE” will be displayed and the
last mode will be resumed.
Press TRACK
ll
to skip to the beginning of the next
track. Press TRACK
nn
to return to the beginning of the
current track. Pressing TRACK
nn
again skips to the
beginning of the previous track.
Press and hold TRACK
ll
or TRACK
nn
to fast
forward or reverse a track.
Press
l
/
II
to temporarily stop USB playback.
Press
l
/
II
again to resume playback.
Press SELECT to enter the file/folder search mode. A list of
all the folders from the USB device will be displayed.
Note: Any files located in the root directory will be located in
the folder named "ROOT". Press SELECT to view the files on
the root folder.
Use the VOL+ or VOL- buttons to cycle through all the
folders on the device and press SELECT to choose the
desired folder. The list of files in the selected folder will be
displayed. Use the VOL+ or VOL- buttons to cycle through
the list of files.
Note: Pressing GO BACK when viewing the contents of a
folder will return to the list of folders on the USB device.
Press GO BACK again to exit the search menu.
Once the desired song is displayed, press SELECT to begin
playback of the desired song.
Note: Due to differences in USB device transfer speeds, it is
recommended to limit each folder to less than 30 songs.
Connecting a USB Device
(sold separately)
Playing Music
Track Select
Fast Forward and
Reverse
Pause
File Search
Step 1
Step 2
Step 3
Tabla de contenidos
Otros manuales de Audio marino de Dual
Dual
Dual AMB500W Instrucciones de funcionamiento
Dual
Dual illumiNITE WDCL65 Instrucciones de funcionamiento
Dual
Dual DMS6516 Instrucciones de funcionamiento
Dual
Dual LU50PB Instrucciones de instalación
Dual
Dual MCP378SXM Instrucciones de funcionamiento
Dual
Dual illumiNITE DMS165L Instrucciones de funcionamiento
Dual
Dual AMBSOOW Instrucciones de funcionamiento
Manuales populares de Audio marino de otras marcas
Nady Audio
Nady Audio M-Cab MC-15 Manual de instrucciones
Fusion
Fusion MS-RA70 Manual de usuario
Garmin
Garmin Fusion APOLLO RV-RA770 Manual de usuario
Boss Audio Systems
Boss Audio Systems ATV25B Manual de usuario
Polk Mono
Polk Mono UM1 Manual de usuario
Garmin
Garmin Fusion Apollo MS-RA670 Manual de usuario