DTS Z8 Manual de usuario
Technical DatasheetTechnical Datasheet
GB
Made in Italy
Z8 LED Controller
User’s Manual Rel 2.3
D.T.S. Illuminazione srl - ITALY
http://www.dts-lighting.it
D.T.S. Code
03.LA.074.V2 (RJ45 OUTPUT)
03.LA.075.V2 (M12 OUTPUT)
03.LA.080.V2 (PLUG-IN OUTPUT)
Le informazioni contenute in questo documento sono state attentamente redatte e controllate. Tuttavia
non è assunta alcuna responsabilità per eventuali inesattezze. Tutti i diritti sono riservati e questo
documento non può essere copiato, fotocopiato, riprodotto per intero o in parte senza previo consenso
scritto della D.T.S .
DTS si riserva il diritto di apportare senza preavviso cambiamenti e modifiche estetiche , funzionali o di
design a ciascun proprio prodotto. D.T.S non assume alcuna responsabilità sull’uso o sull’applicazione
dei prodotti o dei circuiti descritti.
The information contained in this publication has been carefully prepared and checked. However, no
responsibility will be taken for any errors. All rights are reserved and this document cannot be copied,
photocopied or reproduced, in part or completely, without prior written consent from D.T.S.
D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its products
without prior notice. D.T.S. assumes no responsibility for the use or application of the products or circuits
described herein.
Les informations contenues dans le présent manuel ont été rédigées et contrôlées avec le plus grand
soin. Nous déclinons toutefois toute responsabilité en cas d'éventuelles inexactitudes. Tous droits
réservés. Ce document ne peut être copié, photocopié ou reproduit, dans sa totalité ou partiellement,
sans le consentement préalable de .
se réserve le droit d'apporter toutes modifications et améliorations esthétiques, fonctionnelles ou
de design, sans préavis, à chacun de ses produits. décline toute responsabilité sur l'utilisation ou
sur l'application des produits ou des circuits décrits.
D.T.S
D.T.S.
D.T.S.
Las informaciones contenidas en este documento han sido cuidadosamenteredactadas y
controladas. Con todo, no se asume ninguna responsabilidad por eventuales inexactitudes.
Todos los derechos han sido reservados y este documento no puede ser copiado, fotocopiado
o reproducido, total o parcialmente, sin previa autorizaciónescrita de
se reserva el derecho a aportar sin previo aviso cambios y modificaciones de carácter
estético, funcional o de diseño a cada producto suyo. no se asume responsabilidad de
ningún tipo sobre la utilización o sobre la aplicació
n de los productos o de los circuitos descritos.
D.T.S.
D.T.S.
D.T.S.
Z8 LED Controller
2
DESCRIPTION
3
HELIOS Full Colour LED projector
LED projector
Overview
Z8 is a power supply / DMX LED controllers designed to control the following D.T.S. LED products:
FOS 100, FOS 33, TITAN, HELIOS, FOCUS, MINIFOCUS, MR16 LED Range
System
Z8 is fitted with 8 groups of 4 output channels each; max power of each channel is 24W.
Each group can supply and control an independent set-up of D.T.S. LED products at the same
time, like one of the following:
* max 12 x MR16 RGB LED lamps
* max 4 x MR16 Full Color LED lamps
* max 12 x FOCUS RGB LED projectors
* max 4 x FOCUS Full Color LED projectors
* max x FOS 33 LED bars
* max 1 x
* max 1 x FOS 100 led bar
* max 1 x TITAN
Interface
Z8 is fitted with a DISPLAY interface that lets you enter all functions of the internal menu.
DMX
Z8 LED CONTROLLER can be used in 8 DMX modes: 112 ch, 80 ch, 64 ch, 32 ch,14 ch, 10 ch,
1ch or CUSTOM channels mode.
Operating system update
Z8 internal operating system can be updated via computer, through the dedicated D.T.S. RED BOX
interface
Control
Z8 can be controlled by any DMX console.
Construction
Z8 is housed in a sturdy metal case, that offers high resistance to knocks and mechanical stress.
Z8 is rack mountable.
The protection rating against external agents is Ip20.
Connections
DMX IN / OUT connectors: 2 XLR 5-pole by Neutrik and 2 XLR 3-pole by Neutrik
LEDs connector output:
Three models available; RJ45 female connector (03.LA.074.V2) /
8 poles plug-in screw connector (03.LA.080.V2) /
M12 connector (03.LA.075.V2).
The Maximum distance between the Z8 and the last LED unit in the line should not exceed
meters FOS 100 RGBA / WHITE, FOS 33 RGBA / WHITE (3pcs on the same line).
The Maximum distance between the Z8 and the last LED unit in the line should not exceed 50
meters TITAN all models, FOS 100 FULL COLOUR, FOS 33 FULL COLOUR (3pcs on the
same line).
100
for:
for:
Z8 LED Controller
3
MAIN ELECTRICAL CHARACTERISTICS
Input Voltage Range
Vin 90 - 260 Vac
Frequency
50 - 60 HZ
Power Consumption Range
48 - 800 W
Power Factor ( Pf)
0.95 electronic PFC controller
Efficiency
90% typical
Output
Power Output Range : 8
Output Current : 350 mA @ 100% per channel 1,5 - 15W per channel)
500 mA @ 100% per channel in BOOST Mode ,5 - 24W per channel)
Output Voltage : Vout 48V (Constant Current PWM)
Max Load each output:
or 3
HELIOS Full Color LED projector or LED projector.
Min Load each group: 1 x MR16 RGB LED lamp
Control Input
Control Signal : DMX 512
Dimming System :Constant Current PWM
Address Range : DMX 512 channels addressable by display
outputs of 4 channels each.
Max power of each output is 96W (24W per channel).
Max power of each channel is 24W (24W Red, 24W Green, 24W Blue, 24W Amber).
(
(1
15 x MR16 RGB LED lamps or 5 x MR16 Full Color LED lamps or 15 x
FOCUS RGB LED projectors or 5 x FOCUS Full Color LED projectors x FOS 33 LED bars
or 1 x 1 x FOS 100 LED bar or 1 x TITAN
Z8 LED Controller
4
IMPORTANT SAFETY INFORMATION
Fire prevention:
Never locate the fixture on any flammable surface.
Minimum distance from flammable materials: 10 cm
Replace any blown or damaged fuses only with those of identical value
Prevention from electric shock:
High voltage is present inside the unit.
Unplug the unit prior to performing any operation which involves touching the inside of the unit.
This equipment must be grounded, do not connect to non-grounded supplies.
Use only AC supplies 90-260V, 50-60Hz
The unit should never be located in position exposed to rain or in areas of extreme humidity.
A good air ventilation is essential for proper equipment work.
Safety:
The external surface of the unit may exceed 50°C; never handle the unit until at least 5 minutes
have elapsed since the unit was turned off.
Never install the unit in an enclosed area lacking sufficient air flow.
The ambient temperature should not exceed 40°C and should not be lower than -10°C
UNIT DIMENSION
The use of a thermal magnetic circuit breaker is recommended for each Z8.
Unit Dimensions
(LxDxH)
480 x 385 x 88 mm
Weight
7,5 Kg
Packing Dimensions
(LxDxH)
490 x 390 x 90 mm
Weight
8,5 Kg
40 m8 m
432 mm
88
mm
8
3 5 mm
Z8 LED Controller
5
INPUT/OUTPUT CONNECTIONS
5
3
4 2
11=GND
2=DATA-
3=DATA+
DMX IN-OUT connectors
For application where IP65 rating is not necessary, Z8 LEDs cabling connection can be done with a
standard UTP B2 category 5E cable.
For IP65 rating application, D.T.S. reccomed the use of a IP65/68 cable as the
multipolar black outdoor cable (D.T.S. Code: 0509C062).
The Maximum distance between the Z8 and the last LED unit in the line should not exceed
meters FOS 100 RGBA / WHITE, FOS 33 RGBA / WHITE (3pcs on the same line).
The Maximum distance between the Z8 and the last LED unit in the line should not exceed 50 meters
TITAN all models, FOS 100 FULL COLOUR, FOS 33 FULL COLOUR (3pcs on the same line)
TIA/EIA 568-
4X2XAWG24
100
for:
for:
Z8 LED Controller
8 x LEDs output
RJ45 Female panel connector
03.LA.074.V2 (RJ45 OUTPUT)
8-pin Female (RJ45)
RJ45 : 8P8C
8P8C indicates 8 positions 8 cables
1
88-pin Male (RJ45)
Modular Plug
18
18
Mains 90-260 Vac
50-60 Hz
Powercon female panel
connector
Pin 1 = RED +
Pin 2 = RED -
Pin 3 = GREEN +
Pin 4 = GREEN -
Pin 5 = BLUE +
Pin 6 = BLUE -
Pin 7 = AMBER +
Pin 8 = AMBER -
Displays
Mains Switch
6
INPUT/OUTPUT CONNECTIONS
5
3
4 2
11=GND
2=DATA-
3=DATA+
DMX IN-OUT connectors
Mains 90-260 Vac
50-60 Hz
Powercon female panel
connector
Z8 LED Controller
8 x LEDs output
8 poles plug-in screw connector
03.LA.080.V2 (PLUG-IN OUTPUT)
8 poles plug-in screw connector
1---------PIN---------8
Pin 1 = RED +
Pin 2 = RED -
Pin 3 = GREEN +
Pin 4 = GREEN -
Pin 5 = BLUE +
Pin 6 = BLUE -
Pin 7 = AMBER +
Pin 8 = AMBER -
7
Displays
Mains Switch
For application where IP65 rating is not necessary, Z8 LEDs cabling connection can be done with a
standard UTP B2 category 5E cable.
For IP65 rating application, D.T.S. reccomed the use of a IP65/68 cable as the
multipolar black outdoor cable (D.T.S. Code: 0509C062).
The Maximum distance between the Z8 and the last LED unit in the line should not exceed
meters FOS 100 RGBA / WHITE, FOS 33 RGBA / WHITE (3pcs on the same line).
The Maximum distance between the Z8 and the last LED unit in the line should not exceed 50 meters
TITAN all models, FOS 100 FULL COLOUR, FOS 33 FULL COLOUR (3pcs on the same line)
TIA/EIA 568-
4X2XAWG24
100
for:
for:
INPUT/OUTPUT CONNECTIONS
5
3
4 2
11=GND
2=DATA-
3=DATA+
DMX IN-OUT connectors
Mains 90-260 Vac
50-60 Hz
Powercon female panel
connector
Z8 LED Controller
8 x LEDs output
M12 Female panel connector
03.LA.075.V2 (M12 OUTPUT)
Pin 1 = RED +
Pin 2 = RED -
Pin 3 = GREEN +
Pin 4 = GREEN -
Pin 5 = BLUE +
Pin 6 = BLUE -
Pin 7 = AMBER -
Pin 8 = AMBER +
8
M12 LED output
Female panel connector
M12 LED input
Male cable connector
Pin1
234
5
6
7
Pin1
2
3
4
5
67
8
8
Displays
Mains Switch
For application where IP65 rating is not necessary, Z8 LEDs cabling connection can be done with a
standard UTP B2 category 5E cable.
For IP65 rating application, D.T.S. reccomed the use of a IP65/68 cable as the
multipolar black outdoor cable (D.T.S. Code: 0509C062).
The Maximum distance between the Z8 and the last LED unit in the line should not exceed
meters FOS 100 RGBA / WHITE, FOS 33 RGBA / WHITE (3pcs on the same line).
The Maximum distance between the Z8 and the last LED unit in the line should not exceed 50 meters
TITAN all models, FOS 100 FULL COLOUR, FOS 33 FULL COLOUR (3pcs on the same line)
TIA/EIA 568-
4X2XAWG24
100
for:
for:
DMX SIGNAL CONNECTION:
The unit operates using a digital DMX 512 signal. Connection between the controller and the unit or
between units must be carried out using a two pair screened ø 0.5 mm cable and a CANNON XLR 5 pins
connector.
P.S:If the display showing the DMX address flashes, then one of the following errors has occurred:
- DMX signal not present
- DMX reception problem
For Installations where long distance DMX cable connections are needed, we suggest to use a DMX
terminator.
The DMX terminator is a male XLR 3-5 pins connector with a 120 ohm resistor Between pin 2 and 3.
The DMX terminator must be plugged into the last unit (DMX out panel connector) of the DMX line.
Ensure that the conductors do not touch each other. Do not connect the cable ground to the XLR
chassis. The plug housing must be isolated. Connect the mixer signal to the DMX IN of the Z8 plug and
connect it to the next unit by connecting the DMX OUT plug on the first Z8 to the DMX IN plug of the
second one.
This way, all the projectors are cascade connected.
1
2
3
5
4
OUT
120 ohm
PIN 3
PIN 2
PLACE A 120 OHM RESISTOR BETWEEN PIN 2
AND 3 OF A MALE XRL CONNECTOR AND PLUG IT
INTO THE DMX OUT PANEL CONNECTOR OF THE
LAST UNIT CONNECTED TO THE DMX LINE
Z8 LED Controller
5
3
4 2
11=GND
2=DATA-
3=DATA+
Standard
DMX 512
controller
5
3
4 2
11=GND
2=DATA-
3=DATA+
Standard
DMX 512
controller
5
3
4 2
11=GND
2=DATA-
3=DATA+
Standard
DMX 512
controller
9
DMX ADDRESS
Z8 LED CONTROLLER can be used in 8 DMX modes: 112 ch, 80 ch, 64 ch, 32 ch,14 ch, 10 ch,
1ch or CUSTOM channels mode.
Full type - 8 bit
If you want to select the next projector, just add “32”
Z1 type - 8 bit
Projector 1 A001
Projector 2 A011 If you want to select the next projector, just add “10”
Projector 3 A021
….. A….
projector 6 A051
Selelcting the DMX address
1) Press the UP-DOWN key until you reach the required DMX address. The numbers on the
display will start flashing (but the new DMX address hasn't yet been set).
2) Press ENTER to confirm your selection. The numbers on the display will stop flashing and the
projector is now controlled by the new DMX address.
TIPS: if you keep pushed the UP or DOWN keys, the channels are calculated more quickly and
you get a faster selection.
If you want to use the Z8 in 32 channels mode, select the “ ” mode from the
DMX MODE menu under MODE SETTINGS and set the following addresses on the mixer:
Projector 1 A001
Projector 2 A033
Projector 3 A065
….. A….
projector 6 A161
If you want to use the Z8 in 10 channels mode, select the “ ” mode from the
DMX MODE menu under MODE SETTINGS and set the following addresses on the mixer:
Z8 LED Controller
10
Tabla de contenidos
Otros manuales de Equipo de iluminación de DTS
DTS
DTS FREELINE 30 Manual de usuario
DTS
DTS JACK Manual de usuario
DTS
DTS XR 8 Wash Manual de usuario
DTS
DTS DOCTUS.D Series Manual de usuario
DTS
DTS DELTA 8 Series Manual de usuario
DTS
DTS Alchemy 7 Manual de usuario
DTS
DTS XR2000 BEAM Manual de usuario
DTS
DTS TITAN SOLO Manual de usuario
DTS
DTS ALCHEMY 5 Manual de usuario
DTS
DTS Nick Wash 600 Manual de usuario
DTS
DTS DONUT 6 Manual de usuario
DTS
DTS DELTA R FULL COLOR Manual de usuario
DTS
DTS ARTEMIO FRESNEL Manual de usuario
DTS
DTS FOS 100 FULL RGBW Manual de usuario
DTS
DTS FOS 100 SOLO FULL RGBW Manual de usuario
DTS
DTS SCENA COMPACT LED 50 Manual de usuario
DTS
DTS XR 5 WASH Manual de usuario
DTS
DTS Scena LED 150 Manual de usuario
DTS
DTS DELTA R FULL COLOR Manual de usuario
DTS
DTS 03.P16.02.01.LED PAR16 LED MR16 BLACK Manual de usuario
Manuales populares de Equipo de iluminación de otras marcas
Qazqa
Qazqa Suplux SL 3 Black 103062 Manual de usuario
Commercial Electric
Commercial Electric 54568141 Manual de usuario
CREE LIGHTING
CREE LIGHTING 304 Series Manual de usuario
Goobay
Goobay 49867 Manual de usuario
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Manual de usuario
Alkalite
Alkalite Krypton KT-81 Manual de usuario
