DTF Maxima Semi-Auto Manual de usuario
Maxima Semi-Auto
Dual Heat Press
User Manual
1
dtfstation.com
Scan the above code for
technical videos and tips!
2
CONTENTS
1. CONTENTS .............................................................
2. SPECIFICATIONS ..................................................
3. SAFETY ....................................................................
4. INSTRUCTIONS .....................................................
A.Temperature & Time Setting ........................
5. TROUBLESHOOTING ...........................................
6. WARRANTY ...........................................................
2
3
4
5
5
6
7
3
SPECIFICATIONS
Current
Voltage
Power
Temp. Range
Ideal Temp.
Time Range
Platen Size
(WxL)
Machine Size
(LxWxH)
Packaging
Size (LxWxH)
Net Weight
110 V*
3500 W
0-750°F
320°F
0-999 Seconds
16” x 20”
22” x 36.75” x 54.5”
23.65” x 40” x 60”
265 lbs.
*Maxima Semi-Auto Press requires use of air
compressor, which may require a higher
voltage plug or more power.
TEMPERATURE & TIME SETTING
1. Press SET once. “5P” will flash at the top, and the controls will enter
the temperature/time setting state.
2. Use the arrow keys to increase or reduce temperature or time.
3. Once the desired time and temperature are input, press SET once
more to set the time and temperature.
4. Press the up arrow key (with RESET written underneath) for 3
seconds to reset time and temperature settings.
5
INSTRUCTIONS
1. Connect air compressor connector, open the air pressure, adjust the
pressure guage to 60psi, and raise the heating plate.
2. Connect the air switch, turn on the main power switch, and the
indicator light will turn on.
3. Adjust the required time and temperature, and wait for the machine
to heat up.
4. After heating, temperature meter OUT1 light off, automatic flashing
(insulation). Start testing.
5. Place garment on the platen, making sure garment is flat. Place
pressing paper. Adjust mode to manual, and press the start switch.
6. When the set time is up, the heating plate will raise automatically,
and the machine head will move to the other platen.
7. Observe results of test and adjust settings as necessary.
8. After a successful test, the transfer switch can be left to automatic.
After placing materials to be pressed on the platen, as long as the
press is above the platen, it will press automatically.
9. In case of emergency, press the emergency stop button.
6
TROUBLESHOOTING
Distance between 4
sides of top plate and of
bottom plate not uniform
Pressure too high or low
No countdown/timer
When time is up, press
does not press
No temperature control
1. Use a ruler to measure whether the distance
between the 4 sides of both platens is
consistent. If not, screw “down” nut in the
center of the heating plate to adjust.
1. Ideal pressure is about 60psi. Adjust filter.
2. Lift the upper regulating valve in the “+”
direction to increase pressure, or in the “-”
direction to reduce pressure.
3. Check whether pressure of air compressor is
within ideal range of 85-100psi.
1. Make sure machine head is in proper place.
2. Check proximity switch and distance. Adjust
to less than 5mm.
1. Check whether temperature control table,
solid state relay, and heating plate circuit
are in good contact. Also check to ensure
the electrical components are functioning
properly.
1. Check circuit (intermediate relay)
PROBLEMS SOLUTIONS
4
SAFETY
1. Read all instructions and watch all recommended videos.
2. Use heat press only for its intended use.
3. Please use caution when operating this heat press, especially
when the automatic press is in operation.
4. Please ensure that you have suitable and reliable protective
ground wire before using this heat press.
I. Power is 3500 W and voltage is 110 V.
5. To reduce risk of electric shock, do not immerse the heat press
in water or other liquids, and do not store liquids near the heat
press.
6. Never pull cord to disconnect from outlet, instead grasp plug
and pull to disconnect.
7. Do not allow cord to touch hot surfaces. Allow heat press to
cool completely before storing.
8. Do not operate heat press with a damaged cord, or if the
equipment has been dropped or damaged.
9. To reduce risk of electric shock, do not dissasemble or attempt
to repair the heat press. Take it to a qualified service person for
examination and repair. Incorrect assembly or repair could
increase the risk of fire, electric shock, or injury to persons.
10. This appliance is not intended for use by persons (including
children) with reduced physical, sensory, or mental
capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning the use
of the appliance by a personal responsible for their safety.
11. Close supervision is necessary for any heat press being used
by or near children. Do not leave equipment unattended while
connected.
12. Burns can occur when touching hot metal parts.
13. To reduce the likelihood of circuit overload, do not operate
other high voltage equipment on the same circuit.
WARRANTY
7
• 1 year warranty on all parts
• 5 year limited warranty on heating elements
Tabla de contenidos
