DT Research DT382GL Instrucciones de montaje
Rugged Tablet
signage dtri com
DT Research, Inc.
2000 Concourse Drive, San Jose, CA 95131
Copyright © 2020, DT Research, Inc. All Rights Reserved. BOG072820 DT382GL/ DT382GS ENG
INTRODUCTION
The DT Research DT382GL/ DT382GS Rugged Tablet features the integraon of a high
brightness 8” capacive touch screen and a high performance yet energy ecient
processor within a slim, lightweight, durable package. With built-in Wi-Fi, Bluetooth
and a smart card reader as well as opons for back camera, barcode scanner, GNSS,
NFC, and UHF RFID reader, this robust tablet oers seamless informaon capture and
transmission for improved workow. Rated IP65 and MIL-STD-810G, the DT382GL/
DT382GS Handheld Rugged Tablet provides reliable operaon in harsh, mission-
crical environments.
PACKAGE CONTENTS
• One DT382GL/ DT382GS
• One Baery Pack and Handstrap
• AC-DC Power Adapter
• Basic Operaon Guide
* The actual package contents may vary depending on the conguraon acquired.
DT382GL/ DT382GS
Data Capture Modules
Smart Card Reader
Barcode Scanner (oponal)
Back Camera (oponal)
2
Input/ Output Ports
USB Type-C Port (power input)
Audio Jack
USB Port
A
D
C
F
B
E
The DT382GL/ DT382GS
BUTTON ACTION
Power Buon
Windows Key Button
Programmable Buttons
Brightness Control Buttons
RFID Reader Trigger Button/
Programmable Button
Barcode Scanner Trigger Buon/
Programmable Buon
1
4
2
5
3
6
Button Functions
5
6
2
3
B
A
C
D
E
F
1
4
Baery/ Power LED
PRECAUTIONS
• Always exercise care when operang and handling the DT382GL/ DT382GS
• Do not disassemble any poron of the DT382GL/ DT382GS, as this will void any
product warranty.
• Do not use any power adapter or charging cradle other than the one provided
with the tablet or acquired from the manufacturer or its partners.
• In the unlikely event that abnormal noise, strange odor, or smoke is present,
immediately power down the DT382GL/ DT382GS and disconnect all power
sources. Please report the problem to your device provider immediately.
3
OPERATION
Powering ON and OFF
To acvate DT382GL/ DT382GS, push and quickly release the Power Buon. The display
will come on in a few seconds. To put the DT382GL/ DT382GS in standby mode, push
and quickly release the Power Buon. To turn the DT382GL/ DT382GS o for extended
storage, power o safely using any soware funcon that “shuts down computer”
provided in the soware operang system.
NOTE:
The baery packs shipped with your tablet may be low in power - please use the
AC-DC adapter with the DT382GL/ DT382GS when seng up for the rst me to
fully charge the baery pack.
NOTE:
To conserve power, push and quick release the Power Buon to make the tablet
in standby mode while not in use. Pushing briey on the same bu on will wake
up the system.
NOTE:
When the baery pack is charging, the blue-colored Baery LED should blink
slowly. If plugging in the AC-DC adapter does not trigger this blinking acvity
and the LED stays dark, the baery pack(s) may have been drained substanally.
Unplug/ replug the AC-DC adapter to the DT382GL/ DT382GS a few mes to
acvate the charging process.
NOTE:
Avoid using the Power Buon (“hold 4+ seconds” feature) to turn o the
tablet—this form of hardware shutdown is intended to be a means of recovery
from lockups, and not as normal operaon.
3
5
UHF RFID Reader:
The oponal UHF RFID reader supports EPC Gen2V2 and ISO 18000-63 standard. To
develop an applicaon to use the UHF RFID reader, contact your device provider for a
UHF RFID reader API package
Data Capture Module Operation Guide
If your DT382GL/ DT382GS comes with an RFID Reader refer to the steps below to
congure the sengs.
For More Support
Users can download the Tablet Modules Basic Operaon Guides from the DT Research
website.
NOTE:
To ensure the system performance, turn on only the symbologies you are going to use.
4
Start Up
If the power up (from Standby mode or otherwise) is successful, the appropriate
interface will be displayed aer a launch sequence of several seconds. The wireless
LAN connecon may take 10-15 seconds to be established.
Wireless Networking
Wireless LAN
The DT382GL/ DT382GS is oen delivered with an embedded (user-inaccessible)
802.11ac LAN adapter equipped with a hidden custom antenna.
• Through the support of typical WLAN adapters, the DT382GL/ DT382GS should be
able to detect all 802.11 access points in the vicinity for you to select the access
point of your choice for connecon.
• The SSID and WEP/WPA/WPA2 (if enabled) parameters on the DT362G and the
access points have to match. The SSID is case-sensive and it is recommended
that you enable WEP/WPA/WPA2 encrypon (or advanced alternaves) for
secure access.
• When WEP/WPA/WPA2 is enabled, you may need to consult your network
administrator or your networking equipment literature to properly congure
associated sengs such as Authencaon mode, etc.
• Refer to the access point operang manuals for seng up the 802.11 access
points.
Bluetooth
The Bluetooth conguraon applicaon is enabled from the System Tray or from the
Windows Mobility Center. Follow the instrucons and opons provided within the
applicaon to congure and invoke Bluetooth connecvity with the corresponding
peripherals.
7
Federal Communication Commission Interference
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protecon against harmful interference in
a residenal installaon. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instrucons, may cause harmful interference to radio communicaons.
However, there is no guarantee that interference will not occur in a parcular
installaon. If this equipment does cause harmful interference to radio or
television recepon, which can be determined by turning the equipment o
and on, the user is encouraged to try to correct the interference by one of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separaon between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Cauon: Any changes or modicaons not expressly approved by the
party responsible for compliance could void the user’s authority to operate
this equipment.
This device complies with Part 15 of the FCC Rules.
Operaon is subject to the following two condions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operaon.
This device and its antenna(s) must not be co-located or operang in
conjuncon with any other antenna or transmier.
This Class [B] digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du
Canada.
6
Este manual sirve para los siguientes modelos
1
Otros manuales de Tableta de DT Research
DT Research
DT Research DT390i Instrucciones de montaje
DT Research
DT Research DT301X-TR Instrucciones de montaje
DT Research
DT Research DT301Y Instrucciones de montaje
DT Research
DT Research DT365CT Instrucciones de montaje
DT Research
DT Research DT398H Instrucciones de montaje
DT Research
DT Research DT301Y Instrucciones de montaje
DT Research
DT Research DT313C Instrucciones de montaje
DT Research
DT Research DT370CR Instrucciones de montaje
DT Research
DT Research DT311T Instrucciones de montaje
DT Research
DT Research DT370CR Instrucciones de montaje
DT Research
DT Research DT395GS Instrucciones de montaje
DT Research
DT Research DT395CR Instrucciones de montaje
DT Research
DT Research DT313H Instrucciones de montaje
DT Research
DT Research 302MD Instrucciones de montaje
DT Research
DT Research DT301 Instrucciones de montaje
DT Research
DT Research DT311Y Instrucciones de montaje
DT Research
DT Research 313Y/MD Instrucciones de montaje
DT Research
DT Research DT520 Instrucciones de montaje
DT Research
DT Research DT318CR Instrucciones de montaje
DT Research
DT Research DT340T Instrucciones de montaje
