DT Research SP200 Instrucciones de montaje
SP200
ENGLISH
Integrated Player/Server
Appliance
BASIC OPERATION GUIDE
SP200
ENGLISH 4
signage dtri com
DT Research, Inc.
2000 Concourse Drive, San Jose, CA 95131 hp://www.dtresearch.com I hp://signage.dtri.com
Copyright © 2012, DT Research, Inc. All Rights Reserved. DT Research is registered trademark of DT Research, Inc.
INTRODUCTION
Thank you for acquiring the Integrated Player/Server Appliance, part of the
digital signage line by DT Research. The SP200 facilitates the creaon of a unique and powerful
communicaons medium that offers unparalleled opportunies to capture an audience’s aenon
at key decision-making locaons. The DT Research Integrated Player/Server Appliance with pre-
loaded WebDT Content Manager Server soware and WebDT player soware in one box is ready
to perform out-of-box with no separate server needed; enable efficient deployments for digital
signage, with reliable hardware features and innovave server-based soware. The SP200, with
MicrosoWindows Embedded Standard 7, offers remote management of the appliances and
the displayed content with the intuive WebDT Content Manager soware. The SP200 together
with the WebDT soware suite offers an effecve
soluon for delivering and managing messages
that target audiences in the right place, at the right
me.
Package Contents
One SP200 Integrated Player/Server Appliance1.
One security USB dongle2.
One power cord3.
One image recovery DVD4.
Documentaon5.
NOTE: The actual package contents may vary depending
on the configuraon acquired.
1
2
3
4
Major Opon
Video capture card with HDMI, component, composite and S-video inputs•
* The content input with HDCP (High-Bandwidth Digital Content Protecon) will not be supported.
SPECIFICATIONS
System
CPU Intel® Core™ i3, 2.93GHz; Intel® Quad-Core™ i7, 3.2GHz
RAM 4GB DDR3; 8GB upgrade (oponal)
Storage 250GB HDD
Operang System Microso® Windows® Embedded Standard 7
Display Resoluon
2160 x 1920 for 1 x 2 digital signage array or
3840 x 1080 for 2 x 1 digital signage array
(max. DVI/ HDMI resoluon 1920 x 1080 per display)
Video Resoluon Full-HD/ Dual Full-HD
Network Interface 10/ 100/ 1000Mb BaseT LAN
Soware Included WebDT Content Manager Server soware 4.0 and WebDT
Player soware
Input/Output Ports
1 DVI-I; 1 HDMI; 8 Audio jacks; 8 USB 2.0 ports; 1 RJ45
connector for Ethernet; 1 IEEE 1394 port;
oponal WLAN (via internal PCI-Express slot or external USB)
Power
Power Supply 200W ATX
Mechanical
Enclosure Aluminum + steel
Dimensions (H x W x D) 4.09 x 10.4 x 13.3 in/ 104 x 265 x 338 mm
Weight 8.7 lbs/ 3.94 kg
Environmental
Temperature Operaon: 0°C - 40°C; Storage: -20°C - 60°C
Humidity 5% - 95% non-condensing
* Specificaons subject to change without noce.
BOG021012SP200ENG
SP200
Audio jacks USB ports Power buon HDD status indicator
RJ45 connector DVI-I output HDMI port IEEE 1394 port
ENGLISH 23ENGLISH
I/O Ports
Connecng Peripherals
Insert the USB dongle to a USB port (1) and make sure your monitors are connected the SP200 with
video cables (2). Aer the peripherals are well connected, plug the power cord into the SP200 (3)
and insert the other end into a power outlet.
NOTE: DO NOT connect the power cord before connecng the USB dongle and all cables to the SP200
Powering ON and OFF
Warning! Please make sure the selected voltage on the appliance matches the local voltage.
Wrong voltage seng will cause damage to the power supply.
The Power Buon is located on the front of the SP200. To turn the SP200 on, push and release the
Power Buon on the front bezel. The power LED will be lit (blue), and the corresponding interface
will be shown on the display monitors.
To turn offthe appliance, use the soware shutdown interface provided, or unplug the appliance.
In the event of system lockup, unplug or re-plug the power cable. Also, the Power Buon may be
used to perform a reset on the appliance. To reset, push and hold the Power Buon for at least 4
seconds. The system will shut down and all unsaved work may be lost. Pushing on the Power Buon
again will restart the appliance.
Get Started with the SP200
When you boot up the SP200 for the first me, a brief introducon about how to operate the SP200
will be displayed on the screen with instrucons on how to connect to the network and manage
your own WebDT Content Manager from any remote laptop/PC.
To exit the full screen introducon, press “Ctrl+Shi+Space”to
•
exit the WebDT Signage Player.
To re-launch the WebDT Signage Player,
•navigate to Start| All
Programs | DT Research| WebDT Signage Player.
To register this signage appliance to
•another WebDT Content
Manager Server if any, navigate to Start | All Programs | DT
Research | Register WebDT Signage Player again, The Player
Registraon screen should appear. Fill in all fields to register. The
required informaon is marked.
Click OK to register and connect to the preferred WebDT Content Manager Publish Server.
•
Please refer to WCM_Guide.pdf included in your package to start
•managing your content,
playlists and schedules via WebDT Cotnent Manager 4.0.
<1> <2> <3>
Insert the USB dongle. Connect video cables (DVI/ HDMI)
with monitors.
Connect the power cord.
E
A
D C
AB
B F G B H B A
A B C D
E F G H
SP200 Front
SP200 Rear
Otros manuales de Servidor de DT Research
