Drive Osprey Manual de usuario

Remove the two knobs on the rear cover and

unscrew the knob on the end of the freewheel

mode lever. Lift up carefully on the rear cover to

remove.Therearcoverwillstillbeconnectedtothe

scooterbythewhitetaillightconnectorcable.

Installthe seat post. Ensure that the seat post

isalignedsothatthetwoflanges with holes are

facingthe rear oftheproduct. Having these flanges

rotatedinto anyotherposition willresultin instability

intheseat.

Attach the two battery connectors to the

batteries (red to red and black to black).

Removeyour scooterfromits packaging.Raise

thetillerbypushingdownonthetillerlever,lifting

thetiller into place, then releasing the lever.

Replace the rear cover, making sure the tabs

onthebottomoftherearcoverfitintotheslots

inthescooter’s floorboard. Replace and tighten the

two knobs and the freewheel mode knob removed

in Step 2.

Frombehindtheproduct, lookingforward, insert

theseat bolt intoholeon the leftsideof the seat

post.Thisboltisalsoused to adjust the seat height.

Insertthe bolt as farintothehole as it willgo,making

sure that the bolt passes all the way through to the

holeon the opposite side. Install the washer andnut

andtighten them using the includedflatwrench.

Liftthe seatandpulltheswivel leverupatthe

sametime.Lowerthebottomoftheseatonto

theseat post. Releasethe lever,swivel theseat

and push downontheseat until it locksinplace.

1NOTE: Get help when placing the seat onto the

post to avoid scratching the cover shroud.

1. 2. 3. 4.

5. 6. 7. 8.

Insert the armrests into the attachment points

in the seat frame so that the armrests face

forward.

Please Read Before Operating!

For technical assistance, call toll free (866) 621-4933 or (800) 544-5155.

Quick Start Guide

Osprey

Affixthe frontbasket tothebracket onthefront

ofthescooter’stiller

Screw the rearview mirrors directly into the

receptors at the top of the product’s control

panel.

Affix the headrest to the top of the seat by

inserting the headrest posts into the holes in

thetopoftheseat.

Insertandtightenthe includedstar knobsto lock

thearmrestsintoplaceat the desired width.

9. 10.

11. 12.

Fully charge the scooter’s batteries by inserting the round charger connector into the battery charging

terminalonthe scooter’scontrol panel and inserting the 3-pronged plug into a standard electricaloutlet.

Ensurethat the 115V/230Vswitch on the product’sbatterycharger is set to 115V.If the switch is setto230V,the

scooter will not charge properly.Fu ll charging normally takes 6-8 hours, but can take as many as 10 hours

dependingon the batteries’ charge level when starting and the ambient temperature.

13.

Osprey Quick Start Guide

READ BEFORE UNPACKING

This Quick Start Guide offers basic information on initial product

setup only. Read the owner’s manual and all supplemental

information thoroughly before operating the product for

information on safety, battery charging, basic operation, comfort

adjustments, disassembly and care and maintenance.

NOTE:The illustrations provided may not reflect your actual unit.

READ

THIS

FIRST!

Otros manuales de Scooter de Drive

Manuales populares de Scooter de otras marcas

TEKTRO

TEKTRO CHEETAH Manual de usuario

Douglas

Douglas Vespa Sprint Guía de instalación

PLAYTIVE

PLAYTIVE AS-2448 Manual de usuario

Ebinger

Ebinger DONKEY XL Manual de usuario

Flyer

Flyer Mountain Guía del usuario

BackCountry eBikes

BackCountry eBikes Storm Manual de usuario

equipmed

equipmed FreeRoam II Manual de usuario

Yoto

Yoto Lion Manual de usuario

WESTHILL BIKES

WESTHILL BIKES LINK Manual de usuario

BAnff

BAnff eProdigy series Manual de usuario

Winther

Winther 475 Manual de usuario

Jetson

Jetson JBZL17 Manual de usuario

First Choice Mobility

First Choice Mobility Roma Medical Corella S741 Manual de usuario

Carrera

Carrera impel Manual de usuario

Afikim

Afikim Superlight SL-3 Manual de usuario

CareCo

CareCo ZOOM Manual de usuario

Douglas

Douglas Vespa G.S. Manual de usuario

Gazelle

Gazelle with BOSCH System Manual de usuario