DreamCast 32DREAM Manual de usuario
32DREAM FIRE PIT | Installation Manual
D r e a m C a s t
Design and Production Ltd.
⚠DANGER - IF YOU SMELL GAS
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. If odor continues, keep away from the appliance and immediately call your
gas supplier or fire department.
⚠WARNING
Do not store or use gasoline or other flammable vapors and liquids in the
vicinity of this or any other appliance. An L -cylinder not connected for use
shall not be stored in the vicinity of this or any other appliance.
⚠DANGER CARBON MONOXIDE HAZARD
This appliance can produce carbon monoxide which has no odor.
Using it in an enclosed space can kill you.
Never use this appliance in an enclosed space such as a camper,
tent, car or home.
⚠WARNING:
Improper installation, adjustment, alteration, service or maintenance can
cause injury or property damage. Read the installation, operating and mainte-
nance instructions thoroughly before installing or servicing this equipment.
⚠WARNING: FOR OUTDOOR USE ONLY!
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference
We recommend that our fire pits
be installed and serviced by pro-
fessionals that are certified in the
U.S. by NFI
(National Fireplace Institute)
STANDARDS:
CSA 2.41-2014, ANSI Z21.97-2014
CERTIFIED FOR USA & CANADA
OUTDOOR DECORATIVE
GAS APPLIANCES
OUTDOOR FIRE PIT BURNER
32DREAM FIRE PIT | Installation Manual
pg. 2
SAFETY INFORMATION
⚠WARNINGS:
IM ORTANT: This appliance should
be inspected before use and at
least once annually by a qualified
service person.
More frequent cleaning may
be required as necessary. It
is imperative that the control
compartment, burners and
circulating air passageways of the
appliance be kept clean
DANGER: Carbon monoxide
poisoning can lead to death!
CARBON MONOXIDE OISONING:
Early signs of carbon monoxide
poisoning resemble the flu, with
symptoms including headache, dizzi-
ness, or nausea. If you experience these
signs, the Fire Pit may not be working
properly. Get fresh air at once! ave the
Fire Pit serviced. Some people are more
affected by carbon monoxide than oth-
ers,including pregnant women, people
with heart or lung disease or anemia,
those under the influence of alcohol, and
those at high altitudes.
NATURAL GAS AND RO ANE:
To assist in detecting leaks, an odorant
has been added to natural gas and
propane. owever, this odorant can fade,
and gas may be present even though no
odor exists.
WARNING: Any modification to this appliance or its con-
trols can be dangerous.
1. This appliance, as supplied, is only for use with the
type of gas indicated on the rating plate.
2. When this appliance is connected to a fixed piping
system, the installation must cconform with local codes or, in
the absence of local codes, with the National Fuel Gas Code,
ANSI ZZ223.1/NFPA 54; National Fuel Gas Code, National
Gas and Propane Installation Code, CSA B149.1; or Propane
Storage and andling Code, CSA B149.2, as applicable..
3. Keep the appliance area clear and free from
combustible materials, gasoline and other flammable
vapors and liquids
4. Do not burn solid fuel in this appliance. Do not use
this appliance to cook food or to burn paper or other
objects.
5. Children and adults should be alerted to the
hazards of high surface temperatures and should
stay away to avoid burns or clothing ignition.
6. Clothing or other flammable materials should not
be hung from the appliance, or placed on or near
the appliance.
7. Young children should be carefully supervised
when they are in the area of the appliance.
8. Do not use the appliance if any part has been under water.
Immediately call a qualified service technician to inspect the
appliance and to replace any part of the control system and
any gas control which has
been under water.
9. Inspect the appliance before each use
1. Turn the appliance off and let cool
before servicing, installing, repairing or
covering. Any guard or other protective
device removed for servicing the appli-
ance must be replaced prior to operat-
ing the appliance. Only a qualified
service person should install, service,
or repair the appliance.
HIGH ALTITUDE INSTALLATION
Gas fireplaces are tested and approved
for elevations from 0 to 4,500 feet in
Canada and U.S.A.
When installing this fireplace at an ele-
vation above 4,500 feet (in Canada),
check with local authorities. Consult
your local gas utility for assistance in
determining the proper orifice for your
location.
LOCAL CODES
Install and use your Outdoor Fire Pit
with care. Follow local codes. In the ab-
sence of local codes, use the latest
edition of The National Fuel Gas Code
ANSI Z223.1/NFPA 54 available from:
American National Standards Institute Inc.
1430 Broadway New York NY 10018
National Fire Protection Association,Inc.
Batterymarch Park Quincy MA 02269.
Make certain you read and understand
all warnings. Keep this manual for refer-
ence.
32DREAM FIRE PIT | Installation Manual
pg.3
See page 8 of this manual for Gas
Installation Requirements
The Fire Pit has an open base
through which you can bring a gas or
propane line. See Fig. 1.
Please make sure that the gas line is
located only within this area. This will
ensure that the final position of the unit
will not be compromised.
We recommend that gas risers be kept
as low to grade as possible and no
higher than 6” at their highest points.
ATTENTION:
Gas line must be installed by a
licensed contractor in compliance
with local codes.
FIG 1. PLAN AND VERTICAL SECTION
OSITIONING GAS SU LY
16”
2”
20”
35”
12”
32DREAM FIRE PIT | Installation Manual
pg.4
CAUTION:
HEAVY: Use care when lifting
and placing to avoid injury
and damage to property and
the
fire pit itself.
Fire pits will require 2 or more
people to lift.
ATTENTION: Fragile! Concrete may chip or scratch if collided with other hard
materials such as stone, metal, or other concrete. HANDLE WITH CARE!
1. Please refer to ‘Clearances to Combustibles’ guide on page 6 of this guide for placement.
2. Ensure that the final location for the fire pit is as flat and level as possible. Also provide
adequate drainage beneath the opening in the base of the fire pit body.
3. Completely unpack the fire pit.
4. Remove Burner Assembly from fire pit body and carefully set aside.
5. Carefully lift the fire pit and place it in its final position. If there is a gas riser, fire pit vessel
should be placed so that the stub is enclosed within the fire pit body (3).
6. If the fire pit does not sit level, shim appropriately so that it is level and evenly supported.
7. Connect to Natural Gas or Propane Source as per page 9 of this manual.
8. Assemble Burner as per instructions on page 7.
9. Check for leaks and test burner (see page 9 and 14).
10. cover with Decorative Topping media as per instructions onpage 8.
LACEMENT AND ASSEMBLY
32DREAM FIRE PIT | Installation Manual
pg.5
1. Burner Assembly
2. SS Flex Line
3. T-Valve
5. Body
4. Chrome Flange
FIG. 2. Firebowl - Exploded
COM ONENTS
32DREAM FIRE PIT | Installation Manual
pg.6
FIG 3. MINIMUM CLEARNACES TO COMBUSTIBLES
CLEARANCE TO COMBUSTIBLES
32DREAM FIRE PIT | Installation Manual
pg.7
WARNING:
Failure to position parts in
accordance with these diagrams
and instructions and/or failure to
use parts specifically approved
for use with this appliance may
result in property damage or
personal injury.
CAUTION:
Do not remove the metal data
plates attached to the Outdoor
Fire it Burner. These plates
contain important information.
NOTICE:
Installation and repair should
be done by a qualified service
person. The appliance should
be inspected before use and at
least once annually by a qualified
service person. More frequent
cleaning may be required as
necessary. It is imperative that
control compartment, burner and
circulating air passageways of
the appliance be kept clean.
TO ASSEMBLE THE BURNER
1. Connect the Burner Assembly to the gas/propane supply
using the supplied flex connector and following the
instructions on page 9.
2. Carefully leak test all connections following the procedure
on page 8.
3. Fill the burner pan evenly with burner media fully covering
burner ring. Media should be level with the top rim of the pan.
4. Follow the Initial Lighting Instructions on page 12.
Make sure that the flame carries to all parts of the
burner. Turn OFF the appliance and let it cool before
proceeding to the next step.
5. Place and evenly distribute decorative topping (river
stones, crushed glass or lava rock) on top of burner media.
An uneven or excessively thick layer of topping can result in
an uneven flame.
6. Do not use any media not supplied by the manufacturer
32 Dream Fire Pit Includes:
- Ball Valve with Flange
& connectors
- Key Way Mount Ring
- Burner
- Lava rock
- SS flex connector
- LP Regulator (LP units only)
Typical Flame Pattern:
BURNER ASSEMBLY
32DREAM FIRE PIT | Installation Manual
pg.8
MEDIA SECTION
Note: MQ Stones require a lava rock base
CONNECTING TO GAS SU LY
⚠ WARNING:
A qualified service person must
connect the appliance to the gas
supply. Follow all local codes.
CAUTION:
Use only new black iron or steel pipe.Internally tinned copper tubing may be used in certain areas. Use pipe of 1/2” diam-
eter or greater to allow proper gas volume to Outdoor Fire it Burner. If pipe is too small, undue loss ofpressure will
occur.
INSTALLATION ITEMS NEEDED:
Before installing the Outdoor
Fire Pit, make sure you have all items
listed bellow:
• piping (check local codes)
• sealant
• manual shutoff valve
• adjustable (crescent) wrench or pliers
• sediment trap
• tee joints
• pipe wrench
No media
32DREAM FIRE PIT | Installation Manual
pg.9
CONNECTING TO GAS SU LY
INSTALLATION REQUIREMENTS
Installation must include a manual shut-
off valve and gas regulator.
1. Feed fuel line through the base or side
of the fire pit unit.
2. Remove existing valve from fire pit
assembly
3. Disassemble ball valve into 2 parts:
Decorative Chrome Flange and T- Valve.
4. Attach provided 1/2” MIP fittings to
each side of the T-Valve with joint
sealant.
5. Attach gas line to one side of the T-
Valve and the provided SS Flex line to
the other.
6. Place key way mount ring on to
threaded side of T- Valve.
7.Screw decorative flange through out-
side to t-valve securely. The key way
mount ring will enable you to tighten it.
8. Connect free end of SS flex connector
to burner unit
9. Carefully leak test all connections
prior to placing burner intofire pit body
10. Place burner unit into fire pit.
11. Cover with media as described in this
manual.
12. Locate the gas hose out of pathways
where people may trip over it or in areas
where the hose may be subject to acci-
dental damage.
CHECKING GAS CONNECTION
⚠WARNING: Test all gas piping and connec-
tions for leaks after installing or servicing. Correct
all leaks immediately.
⚠ WARNING: Never use an open flame to check
for a leak. Apply a mixture of liquid soap and
water to all joints. Bubbles forming on joints while
the gas is running indicate a leak. Correct all
leaks immediately.
Test ressures in Excess Of 1/2 psi (3.5 k a)
This appliance and its individual shutoff valve
must be disconnected from the gas supply piping
system during any pressure testing of that
system at test pressures in excess of
½ psi (3.5 kPa).
Test ressures Equal To or Less Than 1/2 psi
(3.5 k a) This appliance must be isolated from
the gas supply piping system by closing its
individual manual shutoff valve during any pres-
sure testing of the gas supply piping system at
test pressures equal to or less than ½ psi
(3.5 kPa).
Typical Connection
Ball Valve with Flange:
Decorative Flange
Chrome Ignition Key
T- Valve
32DREAM FIRE PIT | Installation Manual
pg.10
LP-GAS MODELS:
1. Make sure tank valve is in its full off position. (Turn clockwise to stop).
2. Check tank valve features to ensure it has proper external mating
threads. (Tank Valve Marked: USE WIT TYPE 1 )
3. Inspect hose shipped with the unit for damage. Never attempt to use
damaged or plugged equipment. See your local LP Gas Dealer for re-
pairs.
4. After inspecting the LP hose shipped with the unit, follow steps 1
through 11 as described on page 9, but connect the end with the female
fitting on the hose to the T-Valve at step 5.
NOTE: Fuel Supply line must not come into contact with surfaces having
temperatures in excess of 140°F. LP gas cylinder must be kept a mini-
mum of 4.5 feet from the appliance. You must use an approved LP cylin-
der retention device (See photo on pg. 11 for example).
5. When connecting regulator assembly to the tank valve, hand tighten
nut clockwise to a positive stop. DO NOT use a wrench to tighten. Use of
a wrench may damage quick closing coupling nut and result in a haz-
ardous condition.
6. Locate the hose out of pathways where people may trip over it or in
areas where the hose may be subject to accidental damage.
7. Open tank valve fully (counter-clockwise). Turn the on/off valve at the
unit slowly to the on position and use a soapy water solution to check all
connections for leaks before attempting to light the appliance. If a
leak is found, turn tank valve off and do not use the appliance until re-
pairs can be made by a local LP Gas Dealer. DO NOT attempt to make
repairs yourself.
8. Never attempt to use this appliance or any components that have been
damaged or exposed to an accidental fire.
CONNECTING TO GAS SU LY CONT’D: L MODELS
Be certain to mount or set the LP-gas cylinder on a flat
stable surface and retain it to prevent it from tipping.
Purge the gas supply line of any trapped air prior to the
first firing of the unit.
WARNING: During the initial purging and subsequent
lightings, NEVER allow gas valve to remain in "OPEN"
position without first placing a burning match on the top of
the burner.
Test fire the unit after referring to the SAFETY
INFORMATION and LIG TING INSTRUCTIONS.
Tip:
If LP-Gas outdoor firepits are used continuously after
a couple of hours, you could see the possibility of the
flame decreasing in size. If this happens, turn off the con-
trol valve and the tank valve and ait a couple of hours
before lighting again or s itch propane tanks. The
propane tank is freezing up due to the volume of gas
being taken out of the tank.
CHECKING GAS CONNECTION
⚠WARNING: Test all gas piping and connections for
leaks after installing or servicing. Correct all leaks imme-
diately.
⚠ WARNING: Never use an open flame to check for a
leak. Apply a mixture of liquid soap and water to all joints.
Bubbles forming on joints while the gas is running indi-
cate a leak. Correct all leaks immediately.
⚠ WARNING
DO NOT LEAVE FIRE IT UNATTENDED
WHEN IN USE
Tabla de contenidos
Otros manuales de Chimenea al aire libre de DreamCast
