- 1 -
CAUTION:
• Use only on a firm, level surface.
• Do not exceed the rated capacity of this jack.
• This is a lifting device only...do not work under the vehicle without proper support
devices, such as axle stands.
• Make sure that the lifting point is stable and correctly centred on the jack saddle.
• Familiarize yourself thoroughly with this manual before operating to prevent damage
to the jack, property, or personal injury.
CAUTION
SPECIFICATION FOR: Hydraulic Trolley Jack.
Capacity ................................................................................................................2000kg
Lifting range ................................................................................................135 x 385mm
Overall size ........................................................................................550 x 212 x 140mm
Weight ................................................................................................................9kg nett
KNOW YOUR TROLLEY JACK
1. Cylinder Pump.
2. Release Valve.
3. Base.
4. Castor.
5. Oil Filler Plug.
6. Reservoir.
7. Middle Spindle.
8. Frame.
9. Front Wheel.
10. Radius Link.
11. Saddle.
12. Lifting Arm.
13. Cover Plate.
14. Handle Sleeve.
15. Jack Handle.
BEFORE USE
1. If oil spillage is noted, check oil
level, refer to maintenance
section, paragraphs 3
and 4, on page 3.
2. Check to see that the release
valve is opened. (Never more
than two full turns), then
insert the handle into handle
sleeve and pump a couple of full
strokes to purge any
air from the system and evenly
distribute the hydraulic oil.
- 2 -
1. Firmly lock release valve in a clockwise
direction with the end of the jack handle.
2. Place the handle in the sleeve to position
the jack under the lifting point. Check that
the saddle is correctly positioned.
To prevent damage to the jack, or the
vehicle, NEVER MOVE THE JACK WITH THE
HANDLE ON THE RELEASE VALVE.
3. To raise load, insert handle into handle
sleeve and pump up and down fully, until
the desired height is reached.
4. ALWAYS USE AXLE STANDS.
5. To lower load, slowly turn the release valve
anticlockwise two full turns with the end of
the jack handle.
OPERATING INSTRUCTIONS
CARE AND MAINTENANCE
1. When the jack is not in use, the lifting arm and handle sleeve should be kept in the
fully lowered position.
2. Keep the jack clean and lubricated. Oil the points indicated on the diagram below
on a regular basis.
3. To check oil level, fully lower jack on level
ground and remove cover plate (Item 13).
Remove filler plug . The correct level is 5mm
below filler plug hole. If low, add oil as
needed.YOUR JACK WAS FILLED AT THE
FACTORY WITH HIGH GRADE HYDRAULIC
OIL. ONLY USE APPROVED JACK OIL*.
4. After extensive use, the oil supply should be
replaced to ensure longer equipment life. To
drain, remove filler plug and release valve.
Ensure that no dirt gets into the system. Refill
with approved jack oil, as paragraph 3.
5. Check pump piston rod periodically for signs of rust or corrosion. Clean exposed
area with a clean oiled cloth.
* We recommend Shell Telus 22.
- 3-
1. BEFORE POSITIONING THE JACK,YOU SHOULD ENSURE THE FOLLOWING:
IMPORTANT SAFETY TIPS
A. Vehicle should be clear of all
passengers. Transmission should be
in gear (or ‘Park’ for automatic
transmissions) and the handbrake
applied.
B. To prevent vehicle from movement,
wheels should be securely blocked
with wheel chocks.
TO RAISE:
TURN RELEASE
VALVE
CLOCKWISE
TO LOWER:
TURN RELEASE
VALVE
ANTICLOCKWISE
We
Draper Tools Ltd. Hursley Road, Chandler’s Ford, Eastleigh, Hampshire.
SO53 1YF. England.
Declare under our sole responsibility that the product:
Stock No:- 63205. Part No:- TJ2/QL.
Description:- Trolley Jack 2 Tonne Quick Lift.
To which this declaration relates is in conformity with the following directive(s)
98/37/EC.
With reference to: EN292-1:1992, EN292-2:1992, prEN1494:1994 & DIN76024:1984.
JOHN DRAPER
Managing Director 18/07/2000
DECLARATION OF CONFORMITY
63205 PTTJ2|QL bkt 22/1/02 4:36 pm Page 1 (Black plate)
