Doyon EM Series Manual de usuario
EM20 - EM30
Product / Produit:
Serial number / Numéro de série:
DOYON EQUIPMENT INC.
5600, 13th Street
Menominee, MI, USA
Tel.: 1 (906) 863-4401
Canada / US: 1 (800) 338-9886
FAX: 1 (906) 863-6322
Internet: http://www.doyon.qc.ca
e-mail: service@nu-vu.com
1
EM Series Planetary Mixer User Manual
Thank you for choosing our product. Please read this manual carefully
before using for better understanding of operation. Please retain this
manual for future reference.
I. Features
1. Enclosed gear transmission with low noise
2. High transmission efficiency with low energy consumption
3. Flexible speed change
4. Equipped with overload protection
5. Easy to use
II. Parameter
Type EM20 EM30
Bowl cubage (L) 20 30
Power
Voltage (V) See nameplate See nameplate
Frequency (Hz) See nameplate See nameplate
Rated power (W) See nameplate See nameplate
Weight (Kg) See nameplate See nameplate
Shaft speed
(r/min)
Frequency
(Hz)
50 Hz 60 Hz 50 Hz 60 Hz
Gear I 97 120 93 112
Gear II 220 272 167 206
Gear III 316 390 285 351
Dimension
L x W x H (mm)
610 x 600 x 918 688 x 641 x 1145
2
3
III. Installation Attentions
1. Mixers to be located in ventilated place.
2. Please leave reserve space around mixers for installation and operation.
Recommended reserve space: not less than 30cm for above, not less
than 10cm for back and sides, enough operating space for front.
3. Keep mixers away from heat, sunlight and moisture.
4. Keep location area smooth and solid for supporting mixers.
5. Separate power supply from sharing.
6. Working condition for mixers is between 5℃ (humidity below 90%) -
40℃ (humidity below 50%). Mixers should not be working outdoors or
in rain.
IV. Safety Indications
Dear Customers, please check below for the specification of symbols that
appear in this operation manual:
Prohibition Mark
With the sign any action is to be prohibited,
otherwise the product may cause damage or
endanger the personal safety of users.
Warning Mark
With the sign any action should strictly follow the
requirements of the operation, otherwise the product
may cause damage or endanger the personal safety
of users.
Caution Mark
With the sign any action should be paid attention to,
otherwise it will cause product damage because
improper operation will cause other losses
4
V. Safety Attentions
The power parameter please see nameplate. If the voltage
range of the power supply is too wide, it may cause the
mixer unable to start and the motor burnt. In this case,
automatic voltage regulator with big capacity must be
installed for support.
Separate outlet to be used with the guarantee by
correct grounding.
The EM mixers offer a power cord with three-wire
(grounded) plug, which is in accordance with the
standard of three-wire (grounded) outlet. Do not cut
or remove the power cord plug (grounded) in any
case. The plug is able to touch the ground when the
mixer is installed properly. Warning! The plug
should be kept firmly in the socket, otherwise may
cause fire.
Do not release the plug by pulling the wire. Please release
the plug by holding it firmly. Keep the wire free from any
extrusion condition. Machine needs to be unplugged
before installation or moving.
Do not use when wire damaged. The damaged wire
must be replaced in professional repairs.
While mixer is running, attempting to put hand(s) or
finger(s) into the bucket is strictly prohibited in order to
avoid injury.
Turn off the power before accessory change to
avoid injury.
.
5
Keep kids away from mixers for safety consideration.
.
Do not spray wash during cleaning as it will affect
the electrical insulation performance, which may
cause injury.
Scrub-brush and steel brush are also forbidden for
cleaning the mixer to avoid paint damage on the
surface of the mixer.
6
IV. ME20 mixer schematic
1、Front view
1-Support 2-Stainless steel barrel 3-Stirring shaft 4-Handle 5-Connector for mince
processor 6-Press board 7-Mixer 8-Handle for fixate mixer 9-Tool Lock Pin
10-Rotation indication 11-Safety grill 12-Gear change handle
7
2、Back view
13-Nameplate 14-Overload switch 15-Emergency stop
16-Stop button 17-Control panel 18-Cover 19-Base 20-Body
21- Lifting handle 22 -Timer 23-Start button 24-Power light
VII. Operating Instructions:
8
1, Power supply to be checked before using to ensure use of the power is
in accordance with 13 Parameter badge. Power outlet must be
equipped with a good grounding line for safety.
2, Installation of accessory: Use the 21 Lifting handle to lower the bucket
until the lowest point, and fit 8 Mixer into 3 Stirring shaft
3, Installation of bucket: Use the 21 Lifting handle to lower the bucket
until the lowest point, fit the 2 Barrel in, and fixate with 7 Press board
4, Transmission Shift: Stop the mixer from running before speed change，
and adjust the 12 Gear change handle to the desired speed location. If
the 12 Gear change handle can not fit properly in position, please turn
off the mixer and rotate the 3 Stirring shaft for assistance.
5, Remove the accessory: Use the 21 Lifting handle to lower the bucket
until the lowest point, and pull the 9. Handle for fixate mixer with one
hand and remove 8 Mixer with the other hand.
6, Start operation: After installation of the 2 Barrel and the 8. Mixer, put
the material for stirring into the 2 Barrel, and then lift the 2 Barrel to a
fixed position by 21 Lifting handle (Turn 190 degrees
counterclockwise), meanwhile close the 11 Safety grid. Choose the
speed level by turning the 12 Gear change handle and press the 23.
Start button to start running.
7, Safety protection: This mixer is designed with 15 Emergency stop and
14 Overload switch. When operator faces special safety problem, 15
Emergency stop can be pressed for immediate power cut off. The 14
Overload switch allows the mixer to shut off automatically for the
protection of motor when overheat and overload occurs. Under this
circumstance, you just need to reduce the load to a normal level and
press the 14. Overload switch for resumption.
8, Timing: For convenience, our mixers are equipped with timer with the
time range of 0-30 minutes. You can set the timer to by turning 22
Timer to required minute point and press 23 Start Button for activation.
The mixer will stop working automatically when time is up. If you do
9
need the function, just adjust 22 Timer to marked position “HOLD” in
17. Control Panel.
VIII. Accessory Specification
1. Standard Accessories
We have prepared 3 kinds of accessories for different food resource as
below:
2、Cleaning before operation
Please give a thorough clean to the bucket and accessories before your
first use. Please use warm water or neutral detergent for cleaning. Wash
with soda solution or acetum to be followed after first cleaning. Final
rinse in clean water.
Do not use brush with bristle brush or wire brush. Do not use organic solvent like
petrol, acetone for cleaning.
3、Function of accessories
3.1 Beater
The beater is a multi function accessory, with the major functions for
crush of potatoes and other vegetables, stirring cake, paste or frozen
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Mezclador de Doyon
Doyon
Doyon AEF015 Manual de usuario
Doyon
Doyon BTF080 Manual de usuario
Doyon
Doyon AEF015 Manual de usuario
Doyon
Doyon BTF010 Manual de usuario
Doyon
Doyon DOMIX 35 Manual del operador
Doyon
Doyon DOMIX45 Manual del operador
Doyon
Doyon SM-200 Manual
Doyon
Doyon BTF020 Manual de usuario
Doyon
Doyon BTF007 Manual de usuario
Doyon
Doyon SM-200 Manual
