Dover Universal 4797L Manual de usuario
MANUAL
0312-002 Tg0784-PM-SO
UIC MANUAL ID NO. 49170802
INSTRUCTION MANUAL
4797L 4797R
Automatic Board Length Adjustment
(Front Left Reference)
Read this instruction manual carefully and keep it at hand.
••
••
•Before operating the machine, read these safety instructions
carefully and fully understand them.
••
••
•Always keep this instruction manual carefully at hand to refer
it anytime and anywhere.
Before Use
We are grateful to you for purchasing these special specified
products.
Please keep in mind the following items before use.
1. Please read this instruction manual carefully for correct use of
these special specified products.
The following warning signs are classified into three categories
according to the degree of danger.
Please fully understand the meaning of each sign for safety
precautions.
This manual is made of recycled paper.
0312-002 1 Tg0784-PM-SO
SOM-1515-002
Before Use
C-S070-42
INSTRUCTION MANUAL
4797L 4797R
Automatic Board Length Adjustment
(Front Left Reference)
This indicates an imminently hazardous situation
which, if not avoided, will result in death or seri-
ous injury.
DANGER
This indicates a potentially hazardous situation
which, if not avoided, could result in death or seri-
ous injury.
WARNING
This indicates a potentially hazardous situation
which, if not avoided, may result in injury or physi-
cal damage.
CAUTION
Before Use
•Identifying Alert Icons
: This symbol mark represents danger or prompts
warning.
: This symbol mark represents prohibited operations.
: This symbol mark represents forced operations or
instructions.
2. Explained in this manual are only the items different from
those in the instruction manual of the main machine.
Use the instruction manual of the main machine together
with this manual.
3. The contents of this manual are subject to change without
prior notice.
Please contact our marketing department or sales agency for
the detailed information on these special specifications.
0210-001 2 Tg0784-PM-SO
Contents
Page
0210-001 3 Tg0784-PM-SO
Before Use ................................................................................................... 1
Contents ....................................................................................................... 3
1. Scope ..................................................................................................... 5
2. Specifications ......................................................................................... 5
3. Condition of PCB before Placement ...................................................... 7
3.1 When the PCB length of the outline reference is
18.11 inches (460 mm) or less ........ 7
3.2 When the PCB length of the outline reference is beyond
18.11 inches (460 mm)
and 19.94 inches (506.5 mm) or less ....... 8
3.3 When the PCB length of the hole reference is
18.11 inches (460 mm) or less ........ 9
3.4 When the PCB length of the hole reference is beyond
18.11 inches (460 mm)
and 22.05 inches (560 mm) or less .......... 10
3.5 When the PCB length of the hole reference is beyond
22.05 inches (560 mm)
and 24.02 inches (610 mm) or less .......... 11
4. Precautionary Measures for Setup Operation ....................................... 12
5. Items to be Checked before Setup Operation ....................................... 13
6. Setup Operation ..................................................................................... 15
6.1 Setting of Setup Parameters ............................................................ 15
6.2 Overall Setup Operation after Selection of
the [Product Change] Tab .......................................................... 16
6.3 Overall Automatic Setup Function Interlocked with
Program Change ........................................................................ 19
7. Zeroing Operation ................................................................................. 20
8. "Origin/Signal Info." Tab ......................................................................... 22
Contents
Page
9. Maintenance ........................................................................................... 23
9.1 Maintenance Spots ............................................................................ 23
9.2 Inspection ........................................................................................... 23
9.3 Lubrication.......................................................................................... 23
10. Device Offset ....................................................................................... 24
11. Material ................................................................................................. 25
11.1 Parts Location .................................................................................. 25
Layout of Main Machine Section 1 for 4797L (C) ............................ 25
Layout of Main Machine Section 1 for 4797L (D) / 4797R (D) ........ 26
11.2 Layout of Sensors and Loads .......................................................... 27
X/Y Table Section ............................................................................ 27
11.3 Electrical Circuit Diagrams ............................................................... 28
Integrated Block Connection Diagrams ........................................... 28
PPC-Axis Motor Circuit Diagrams.................................................... 29
11.4 Cord Connection Diagrams ............................................................. 30
X/Y Table Section ............................................................................ 30
C-S070-42 Connection Diagrams 1 ................................................. 31
0312-002 4 Tg0784-PM-SO
5Tg0784-PM-SO0312-002
1. Scope
When a program change is made, the P.C.B. locate pin / P.C.B.
locate lever can be adjusted automatically, shortening the machine
setup time.
2. Specifications
Table 1
1. Scope
6Tg0784-PM-SO0312-002
2. Specifications
7Tg0784-PM-SO0210-001
3. Condition of PCB before Placement
3. Condition of PCB before Placement
3.1 When the PCB length of the outline reference is
18.11 inches (460 mm) or less
8Tg0784-PM-SO0210-001
3. Condition of PCB before Placement
3.2 When the PCB length of the outline reference is
beyond 18.11 inches (460 mm) and 19.94 inches
(506.5 mm) or less
9Tg0784-PM-SO0210-001
3. Condition of PCB before Placement
3.3 When the PCB length of the hole reference is
18.11 inches (460 mm) or less
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Manuales populares de Electricidad industrial de otras marcas
S&C
S&C Vista SD Manual de usuario
Murata
Murata GRM0335C2A7R3CA01 Series Manual de usuario
Siemens
Siemens 3VA9988-0BM10 Manual de usuario
Siemens
Siemens SITRANS LVS100 Manual de usuario
Murata
Murata GRM32ER60G227ME05 Series Manual de usuario
Siemens
Siemens SENTRON SUPERSWITCH 3KL82 Series Manual de usuario