DNF Controls SW32PS-RCP Manual de usuario
12843 Foothill Blvd. Suite C
Sylmar, California 91342
V: 818.898.3380
F: 818.898.3360
sales@dnfcontrols.com
Model No. SW32PS-RCP
RS422 PORT SWITCHER
REMOTE CONTROL PANEL
User Manual
Rev 1.01
SW32PS-RCP Port Switcher Controller Page 1
1
o
of
f
1
13
3
TABLE OF CONTENTS
REVISION HISTORY 2
GETTING STARTED . . . 3
1. DESCRIPTION 3
2. INSTALLATION 3
3. CONNECTION DIAGRAM 4
4. OPERATION 5
a. MAKE A ROUTE 5
b. VIEW THE ROUTES 5
c. DISCONNECT ROUTE 5
d. SAVE PRESET 5
e. RESTORE PRESET 5
f. SETUP GANG 6
g. DISCONNECT GANG 6
5. SELF-TEST PROCEDURE 7
a. KEYBOARD TEST 7
b. SYSTEM PORT TEST 7
REFERENCE . . . 9
6. SPECIFICATIONS 9
POWER CONNECTOR 9
RS422 SERIAL CONNECTOR 9
GPI CONNECTOR 10
7. FRONT PANEL LAYOUT 11
8. DNF CONTROLS LIMITED WARRANTY 13
Manual Version ......................................................1.01 090407
Document No: ........................... SW32PS-RCP_User_Manual.doc
Page 2
2
O
Of
f
1
13
3
SW32PS-RCP Port Switcher Controller
1.REVISION HISTORY
080505 1.0 Original document.
090407 1.01 Corrected ID Switch numbering.
SW32PS-RCP Port Switcher Controller Page 3
3
o
of
f
1
13
3
Getting Started . . .
2.DESCRIPTION
The control panel consists of the ST100 controller hardware and the special
software that allows controlling the SW32PS for the following functionality:
Make route, view routes, gang outputs to input, disconnect route, disconnect
gang, save preset, restore preset.
Easy to read LCD Display has 2 lines by 20 characters.
Shows source (From) and destination (To) routing and gang information.
6-function keypad provides:
From (Select Source)
To (Select Device)
View (View active router)
Take (Enable the selected route)
Gang (User control of multiple destinations)
Preset (Select Preset)
Ideal for: Television Stations, Video Productions, Cable TV, Video Post
Production, Duplication Houses
NOTE:Words enclosed in brackets, such as [TAKE] indicate buttons on the
SW32PS-RCP. Buttons shown with a “+” between them, for example
[SHIFT] + [TAKE], indicate two keys pressed simultaneously.
3.INSTALLATION
a. Plug one end of a 9-pin cable into the connector labeled “VTR” on the
back of the controller. Plug the other end into one of the connectors
on the port expander. Plug the port expander into the connector
labeled “RS422” on the back of the SW32PS port switcher.
b. Dip Switches Configuration for SW32PS-RCP.
Every SW32PS-RCP has to have a unique ID from 1 to 10. The ID
should match the External Device number set in the SW32PS.
For example, if you use only one SW32PS-RCP with the SW32PS, the
External Device should be set to 1 and the ID of the RCP should be 01.
(The ID can be seen on the second line of the display during the power
up of the RCP.)
If you use two SW32PS-RCPs with the SW32PS, the External Device
should be set to 2 and the ID of the RCPs should be 01 and 02. (The
IDs can be seen on the second line of the display during the power up
of the RCP.)
Use the table below to set the switches for the desired ID:
SW6 SW5 SW4 SW3 SW2 SW1
ID: 01 Left Left Left Left Left Right
ID: 02 Left Left Left Left Right Left
ID: 03 Left Left Left Left Right Right
ID: 04 Left Left Left Right Left Left
ID: 05 Left Left Left Right Left Right
ID: 06 Left Left Left Right Right Left
ID: 07 Left Left Left Right Right Right
ID: 08 Left Left Right Left Left Left
ID: 09 Left Left Right Left Left Right
ID: 010 Left Left Right Left Right Left
c. Connect DB9F side of supplied power supply into the connector labeled
“Power”. Then connect the IEC to Edison cable to the power supply.
Connect the power cable to 90 VAC to 240 VAC source.
Caution: Do Not Hot Plug the Power Supply DB9F connector!
Installation is complete.
4.CONNECTION DIAGRAM
TYPICAL CONNECTION DIAGRAM
Page 4
4
O
Of
f
1
13
3
SW32PS-RCP Port Switcher Controller
SW32PS-RCP Port Switcher Controller Page 5
5
o
of
f
1
13
3
5.OPERATION
a. MAKE A ROUTE
1) Press [FROM]. The FROM indicator will turn on. The left side
of the display shows the currently selected FROM connector
(PORT1-32).
2) Turn the Wheel until the desired FROM point is displayed.
3) Press [TO]. The TO indicator will turn on. The right side of the
display shows the currently selected TO connector (PORT1-32).
Turn the Wheel until the desired TO point is displayed.
4) Press [TAKE] to route the FROM input to the TO output.
NOTE: No Route is made until [TAKE] is pressed.
NOTE: The Route that involves the selected FROM and/or TO will be
disconnected prior to making the new route.
b. VIEW THE ROUTES
1) Press [VIEW]. The VIEW indicator will turn on.
2) Turn the Wheel to scroll through all ports that are displayed on
the first line of the display.
c. DISCONNECT ROUTE
1) Press [FROM].
2) Turn the Wheel until OFF is displayed.
3) Press [TO].
4) Turn the Wheel to find the destination that you wish to turn off.
5) Press [TAKE] to turn off the route.
d. SAVE PRESET
1) Press [SHIFT] + [PRESET]. The PRESET indicator will turn
on. The first line of the display will show “Save Preset 1”.
2) Turn the Wheel to select preset number 1-8.
3) Press [TAKE] to save current configuration into the selected
preset.
OR
Press [ESC] to exit without saving.
e. RESTORE PRESET
1) Press [PRESET]. The PRESET indicator will turn on.
The first line of the display will show “Restore Preset 1”.
2) Turn the Wheel to select preset number 1-8.
3) Press [TAKE] to restore selected preset.
OR
Press [ESC] to exit without restoring.
Page 6
6
O
Of
f
1
13
3
SW32PS-RCP Port Switcher Controller
f. SETUP GANG
1) Press [FROM]. The FROM indicator turns on. The left side of
the display shows the currently selected FROM connector
(PORT1-32).
2) Turn the Wheel to select the source port.
3) Press [TO]. The TO indicator turns on. The right side of the
display shows the currently selected TO connector (PORT1-32).
4) Press [GANG]. The GANG indicator turns on.
5) Turn the Wheel to select the destination port.
6) Press [TAKE] to route the selected input to the selected
destination. The second line of the display will show “PORT(X)
Added”.
7) Repeat steps 5-6 to add additional routes to GANG.
8) Press [ESC] when done. FROM, TO and GANG indicators turn
OFF.
NOTE: The GANG function will only work properly if the GANG is
Enabled on the SW32PS. It is the responsibility of the user to
set GANG to Enabled in the SW32PS Setup Menu. (See the
SW32PS Port Switcher User Manual for the instructions on how
to enable / disable gang.)
g. DISCONNECT GANG
1) Press [VIEW].
2) Turn the Wheel to find the GANG to be disconnected.
3) Press [GANG]. The display will prompt “Disconnect switches?”
4) Press [TAKE] to break all the routes that are part of gang.
OR
Press [ESC] to exit.
Tabla de contenidos
