Dnake S213K Manual de usuario
User Manual
———
DNAKE S213K
REMARK
Please follow the user manual for correct installation and testing. If there is any
doubt please call our tech-supporting and customer center.
Our company applies ourselves to reformation and innovation of our products. No
extra notice for any change. The illustration shown here is only for reference. If
there is any difference, please take the actual product as the standard.
The product and batteries must be handled separately from household waste.
When the product reaches the end of service life and needs to be discarded,
please contact the local administrative department and put it in the designated
collection points in order to avoid the damage to the environment and human
health caused by any disposal. We encourage recycling and reusing the material
resources.
CATALOG
PRODUCT FEATURE ............................................. 1
TECHNICAL PARAMETER ..................................... 1
PACKAGE CONTENT ............................................. 2
OVERVIEW.............................................................. 3
BASIC OPERATION ................................................ 5
WEB SETTING ........................................................ 7
SYSTEM DIAGRAM .............................................. 20
DEVICE WIRING ................................................... 21
INSTALLATION...................................................... 23
TROUBLESHOOTING........................................... 27
SAFETY INSTRUCTION ....................................... 28
1
PRODUCT FEATURE
1. Powered by PoE or power adapter (DC12V/2A)
2. Support IC (13.56MHz) & ID (125kHz) card, NFC
3. 3 Indicator Lights
4. 2 relays supported
5. Tamper alarm
6. Keypad supported
TECHNICAL PARAMETER
Power Supply: PoE (802.3af) or DC 12V/2A
Standby Power: 1.5 W
Rated Power: 3.5 W
Resolution: 1280 x 720
Working Temperature: -40℃to +55℃
Storage Temperature: -40℃to +70℃
Working Humidity: 10% to 90% (non-condensing)
2
PACKAGE CONTENT
MODEL: S213K (Surface Mounting)
S213K Wiring Cover
Sealing Plug of
Wiring Port
Junction Pressing PM2.5×6 (4 pcs)
Rear Cover
Screw Fixing Seat
(2 pcs)
PA4×30 (2 pcs)
PM4×20 (2 pcs)
FM3×4.5 (2 pcs)
Wrench Screw Diode (2 pcs) Quick Start Guide
MODEL: S213K (Flush Mounting)
S213K
Wiring Cover
Sealing Plug of
Wiring Port
Junction Pressing
PM2.5×6 (4 pcs)
Flush Mounting
Box
Screw Fixing Seat
(4 pcs)
PA4×30 (4 pcs)
Mounting Bracket
(2 pcs)
PM2.5×6 (4 pcs)
FM3×20 (4 pcs) PM3×8 (2 pcs) Decorative Panel Wrench Screw Diode (2 pcs)
Quick Start Guide
3
OVERVIEW
4
Note:
Calling indicator light: The 1st indicator light will activate if the call button is
pressed.
Talking indicator light: The 2nd indicator light will activate if the call is picked up
or the Door Station is being actively monitored.
Unlocking indicator light: The 3rd indicator light activates for 3 seconds when
the door is unlocked.
Relay Outputs: Supports 2 relay outputs.
5
BASIC OPERATION
1. Call and Monitor
1.1. Call Indoor Monitor
In standby mode, press button on Villa Station to call Indoor Monitor. Each button
on Door Station is related to the fixed room number as shown in the picture
below. During the call, press button on Villa Station again to end the call. If the
call fails or Indoor Monitor is busy, Villa Station will make a beep sound.
1.2. Call Indoor Monitor with different room number
Go to Door Station's webpage to change mode into unit. In this mode, users can
press room number+#/dial button to call Indoor Monitor with different room
numbers.
1.3. Monitor Villa Station
Click Doors icon on Indoor Monitor’s homepage to monitor Villa Station.
1.4. Call Master Station
Press the button “ ” to call Master Station.
2. Add Cards by Admin Card
2.1. Add other cards
Step 1: Tap the admin card once;
Step 2: And then tap other cards immediately. Other cards you have tapped can
be used to open the door;
Step 3: Tap the admin card again to finish.
2.2. Delete other cards one by one
Step 1: Tap the admin card twice;
6
Step 2: And then tap other cards immediately. Other cards you have tapped will
be deleted;
Step 3: Tap the admin card again to finish.
2.3. Delete all other cards
Tap the admin card five times. All the other cards will be deleted.
Tips: The admin card can only be used to manage cards. It cannot be used
to open the door.
3. Unlock by PIN Code
In a standby mode, press # button and enter the Password (default is 0000).
Then press # button to confirm. If the password is correct, the door will be
unlocked; If not, it will make a clattering sound.
Tabla de contenidos
Otros manuales de Sistema de intercomunicación de Dnake
Dnake
Dnake S213M Manual de usuario
Dnake
Dnake S215 Manual de usuario
Dnake
Dnake E416 Manual de usuario
Dnake
Dnake TWK01 Manual de usuario
Dnake
Dnake 302 Series Manual de usuario
Dnake
Dnake 290M-S8 Manual de usuario
Dnake
Dnake A416 Manual de usuario
Dnake
Dnake C112 Manual de usuario
Dnake
Dnake 280M-S8 Manual de usuario
Dnake
Dnake E211 Manual de usuario
Dnake
Dnake IPK03 Manual de usuario
Dnake
Dnake 902D-B6 Manual de usuario
Dnake
Dnake H618 Manual de usuario
Dnake
Dnake S215 Manual de usuario
Dnake
Dnake 905D-Y4 Manual de usuario
Dnake
Dnake 280SD-C12 Manual de usuario
Dnake
Dnake 902M S8 Manual de usuario
Dnake
Dnake 905D-Y4 Manual de usuario
Dnake
Dnake 902D-B9 Manual de usuario
Dnake
Dnake E416 Manual de usuario
