DMP Electronics XT Lite Manual de usuario

InstallatIon GuIde

Xt lIte™ Panel

MODEL XTL

INSTALLATION GUIDE

FCC NOTICE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

Reorient or relocate the receiving antenna.•

Increase the separation between the equipment and receiver.•

Connect the equipment into an outlet on a circuit different from that to which the receiver is•

connected.

Consult the dealer or an experienced radio/TV technician for help.•

Changesormodicationsnotexpresslyapprovedbythepartyresponsibleforcompliancecouldvoidthe

user’s authority to operate the equipment.

This device has been designed to operate with the integrated PCB antenna having a maximum gain of 1.8

dB. Antennas having a gain greater than 1.8 dB are strictly prohibited for use with this device. The required

antenna impedance is 50 ohms.

If necessary, the installer should consult the dealer or an experienced radio/television technician

foradditionalsuggestions.Theinstallermayndthefollowingbooklet,preparedbytheFederal

Communications Commission, helpful:

“How to identify and Resolve Radio-TV Interference Problems.”

ThisbookletisavailablefromtheU.S.GovernmentPrintingOfce,WashingtonD.C.20402

StockNo.004-000-00345-4

©2010DigitalMonitoringProducts,Inc.

InformationfurnishedbyDMPisbelievedtobeaccurateandreliable.

This information is subject to change without notice.

XTL Installation Guide Digital Monitoring Products

table of Contents

Panel Specications

1.1 Power Supply .........................................1

1.2 Communication.......................................1

1.3 Keypads .................................................1

1.4 Number of Zones ....................................1

1.5 EnclosureSpecications ..........................1

Introduction

2.1 SystemCongurations.............................2

2.2 Caution Notes.........................................2

2.3 Compliance Instructions ..........................2

System Components

3.1 Accessory Devices...................................3

Installation

4.1 MountingtheEnclosure...........................4

Primary Power Supply

5.1 DC Input ................................................4

Secondary Power Supply

6.1 Standby Battery......................................5

6.2 Replacement ..........................................5

6.3 Battery Supervision .................................5

LED Operation

7.1 BacklitLogo............................................6

Reset Button

8.1 Description.............................................6

Programming Connection

9.1 ProgrammingConnection ........................6

On-Board 1100 Series Wireless

10.1 Wireless Antenna ...................................6

10.2 LED Operation ........................................6

Wireless Keypads

11.1 MountingKeypads ..................................7

11.2 Wireless Keypad Association ....................7

11.3 ExistingKeypadConrmation...................7

Wireless Zones

12.1 Description.............................................7

Flash Load Button

13.1 Description ............................................8

Listed Compliance Specications

14.1 Introduction ...........................................9

14.2 UseMarking ...........................................9

14.3 NFPA 72.................................................9

14.4 Types Of Service .....................................9

14.5 Bypass Reports.......................................9

14.6 Battery Standby......................................9

Digital Monitoring Products XTL Installation Guide

table of Contents

Household Burglar-Alarm System Units

ANSI/UL 1023

15.1 Bell Cutoff ..............................................9

15.2 Entry Delay ............................................9

15.3 Exit Delay...............................................9

15.4 Wireless External Contact ........................9

15.5 Wireless Supervision Time .......................9

15.6 Wireless Audible Annunciation .................9

15.7 Panel location .........................................9

15.8 Test Frequency .......................................9

Central Station Burglar Alarm Units

ANSI/UL 1610

16.1 Standard Line Security ..........................10

16.2 Remote Disarm.....................................10

16.3 Central Station......................................10

Household Fire Warning System

ANSI/UL 985 NFPA 72 Specications

17.1 BellOutputDenition ............................10

17.2 HouseholdSystem ................................10

17.3 Wireless External Contact ......................10

17.4 Wireless Supervision Time .....................10

17.5 WirelessFireVerication........................10

17.6 Battery Standby....................................10

17.7 Test Frequency .....................................10

False Alarm Reduction Programmable Options

ANSI/SIA CP-01-2007

18.1 ShippingDefaultsandRecommendedProgramming11

18.2 Entry Delay ..........................................12

18.3 Local Bell .............................................12

18.4 Minimum Installation Requirements........12

Revisions to This Document

Listings and Approvals

XTL Installation Guide Digital Monitoring Products

Panel sPeCIfICatIons

Panel Specications

1.1 Power Supply

Input:   12VDC

StandbyBattery: 3.7VDCLithium

All circuits inherent power limited

1.2 Communication

Built-inCellularcommunicationtoDMPModelSCS-1RReceivers.CellularServiceisrequiredbeforeusing

theXTLforsignaltransmission.TheXTLpanelcomeswithaSIMcardreadyforactivationwithSecureCom

Wireless,LLC.Moreinformationisavailableatwww.securecomwireless.com.

1.3 Keypads

Youcanconnectupto4alphanumeric9000Serieswirelesskeypads.

1.4 Number of Zones

XTLhas28wirelessinitiatingzonesnumbered1-28•

Zonenumbers31to34and41to44cansupport1100SeriesKeyFobsorDMPwirelessoutputmodules•

1.5 Enclosure Specications

TheXTLpanelshipsinaplasticenclosurewithauser’sguideandprogrammingsheet.

Size Color

5.58”Wx3.75”Hx1”D White(W)

Digital Monitoring Products XTL Installation Guide

IntroduCtIon

Introduction

2.1 System Congurations

The panel can be programmed to operate as any of the following system types:

• All/Perimetersystemthatprovidesoneperimeterareaandoneinteriorarea

• Home/Sleep/Awaysystemthatprovidesoneperimeter,oneinterior,andonebedroomarea.The

bedroom area provides for any protection devices the user wants disarmed during their sleeping hours

and armed in the Away mode.

• Sixareasystemthatprovidesareasofprotectionthatcanbeindependentlyarmedordisarmed.

2.2 Caution Notes

Throughoutthisguideyouwillseecautionnotescontaininginformationyouneedtoknowwheninstalling

thepanel.Thesecautionsareindicatedwithayieldsign.Wheneveryouseeacautionnote,makesureyou

completely read and understand its information. Failing to follow the caution note can cause damage to the

equipment or improper operation of one or more components in the system.

2.3 Compliance Instructions

ForapplicationsthatmustconformtoalocalauthoritiesinstallationstandardoraNationalRecognized

TestingLaboratorycerticatedsystem,pleaseseetheListedComplianceSpecicationssectionneartheend

of this guide for additional instructions.

XTL Installation Guide Digital Monitoring Products

system ComPonents

System Components

3.1 Accessory Devices

DMP Two-Way Wireless Devices

1100R Repeater Provides additional range for wireless devices.

1101UniversalTransmitter Provides both internal and external contacts that may be used at the same time to yield two

individualreportingzonesfromonewirelesstransmitter.

1102UniversalTransmitter Provides one external contact.

1103UniversalTransmitter Provides both and internal and external contacts that may be used at the same time to

yieldtwoindividualreportingzonesfromonewirelesstransmitter.RequiresEOLresistorfor

external contact.

1105UniversalTransmitter Provides both internal and external contacts that may be used at the same time to yield two

individualreportingzonesfromonewirelesstransmitter.

*1114Four-ZoneExpander ProvidesfourwirelesszoneswithEOLresisters.

*1116RelayOutput Provides one Form C relay.

*1117LEDAnnunciator Provides a visual system status indicator.

*1119DoorSounder Provides a battery operated sounder

*1121PIRMotionDetector Provides motion detection with pet immunity.

1125PIRMotionDetector

Providesmultiplelenscongurations,dualcoverageareaselection,andsensitivityadjustments.

*1126C/*1126R/*1126WPIR

MotionDetector

CeilingmountmotiondetectorwithpanelprogrammablesensitivityandDisarm/Disable

functionality.

1127C/1127WPIRMotion

Detector

WallmountmotiondetectorwithpanelprogrammablesensitivityandDisarm/Disable

functionality.

*1129GlassbreakDetector Detectstheshatteringofframedglassmountedinanoutsidewallandprovidesfull-pattern

coverage and false-alarm immunity.

*1131RecessedContact

Provides concealed protection for doors, windows or other applications.

1135Siren Provides a battery operated siren

*1139BillTrap Providesasilentalarmoptionforretailandbankingcashdrawers.

1142BCTwo-buttonPanicBelt

Clip Transmitter

Provides portable two-button panic operation.

1142Two-buttonPanicTransmitter

Provides permanently mounted under-the-counter two-button panic operation.

*1145(Four-Button)

*1146(Two-Button)

*1147(One-Button)

KeyFobtransmittersdesignedtoclipontoakeyringorlanyard.

1161ResidentialSmokeDetector Residentialsmokedetectorwithsounder.

1162ResidentialSmokeDetector Residentialsmoke/heatdetectorwithsounderandxedrate-of-riseheatdetector.

Keypads

LCDkeypads Allowsyoutocontrolthepanelfromvariousremotelocationsusing9000SeriesWireless

Keypads.

* These devices have not been investigated and shall not be used in listed installations

Digital Monitoring Products XTL Installation Guide

InstallatIon

Installation

4.1 Mounting the Enclosure

TheenclosurefortheXTLpanelmustbemountedusingtheprovided#6screwsinthefourmountingholes

showninFigure2.Mounttheenclosureinasecure,dryplacetoprotectthepanelfromdamagedueto

tampering or the elements. It is not necessary to remove the PCB when installing the enclosure.

65555

RESET

LOAD

BAT

PROG

RED

PWR

MODEL XTL

Mounting Hole

Locations

TX RF RX

Figure 2: Mounting Hole Locations

Primary Power Supply

5.1 DC Input

MounttheXTLpanelnearawalloutletfortheModel372-500plug-inDCpowersupply.Inadditionto

poweringthepanel,theDCplug-inpowersupplyalsochargestheback-upbattery.The372-500mustbe

locatedwithin100feetofthepanelusing22AWGwireor250feetusing18AWGwire.Usethefollowing

steps to connect the plug-in power supply:

1.Using18or22AWGwire,connectthepanelPWR(J2)rstterminal(+)tothepositiveterminalon

the power supply.

2.ConnectthepanelPWR(J2)secondterminal(-)tothenegativeterminalonthepowersupply.

3.Plugthepowersupplyintoa110VoltACdedicatedoutletnotcontrolledbyaswitch.

65555

RESET

LOAD

BAT

PROG

RED

PWR

MODEL XTL

Wire Exits for DC

Power Supply

TX RF RX

Model 372-500

DC Plug-in

Power

Supply

Use 18 AWG or 22 AWG for

Power Supply connection

Figure 3: DC Power Supply Connection

XTL Installation Guide Digital Monitoring Products

InstallatIon

Secondary Power Supply

6.1 Standby Battery

TheXTLrechargeablebatteryisusedtoprovide24hoursofbackupbatterypowerwhenDCpowerisnot

available.ThebatteryisintendedforbackuppoweronlyandnottooperatetheXTLpanelonadailybasis.

Ifthebatteryislow,ornotpluggedintotheJ1batteryconnector,alowbatteryconditionisindicatedbythe

XTLpanel.

Note:IfremovingtheXTLpanelfromservice,disconnectthebackupbatteryfromtheXTLconnector.

6.2 Replacement

UsethefollowingstepstoreplacetheXTLstandbybattery.DMPrecommendsreplacingthebatteryevery3

years under normal use.

Top PCB Snaps

Bottom PCB Snaps Battery

connector

3.7V

Rechargeable

Battery

Figure 4: Standby Battery Replacement

1. Unplugthebatteryconnector(J1)fromtheXTLpanel.

2. LoosenthetopPCBsnaps.

3. LeanthepanelPCBforwardandliftoutfromthebottomPCBsnaps.

4. Removeandproperlydisposeoftheusedbattery.

 Caution:Riskofre,explosion,andburns.Donotdisassemble,heatabove212°F(100°C),

or incinerate. Properly dispose of used batteries.

5. PlacethenewbatteryintotheXTLhousingbasewiththebatterywiresdirectedtowardthe

bottomrightcorner.SeeFigure4.

6. SettheXTLPCBintothebottomsnapsandpressintothetopsnapstosecureinplace.

7. Plugthebatteryintothepanelconnector(J1).

6.3 Battery Supervision

ThepanelteststhebatteryonceeveryhourwhenDCpowerispresent.Thistestoccurs15minutespast

eachhourandlastsforveseconds.Aloadisplacedonthebatteryandifthebatteryvoltageislow,alow

batteryisdetected.IfDCpowerhasfailed,alowbatteryisdetectedanytimethebatteryvoltagefalls

below3.7V.

Digital Monitoring Products XTL Installation Guide

InstallatIon

LED Operation

7.1 Backlit Logo

ThebacklitlogoindicatesthePowerandArmedstatusofthepanel.Dependingontheoperation,theLED

displaysinRedorGreenaslistedinthetable.

Color and Activity Operation

GreenSteady PanelDisarmed,ACPowerOK,BatteryOK

GreenBlinking PanelDisarmed,ACPowerOK,BatteryFault

NoLight PanelDisarmed,ACPowerFault,BatteryOK

RedSteady PanelArmed,ACPowerOK,BatteryOK

Red/GreenAlternate PanelArmed,ACPowerOK,BatteryFault

RedBlinking PanelArmed,ACPowerFault,BatteryOK

Reset Button

8.1 Description

Theresetbutton(S1)islocatedontherightsideofthecircuitboardandisusedtoresettheXTL

microprocessor.Toresetthepanelwhenrstinstallingthesystem,presstheresetbuttonafterapplying

power to the panel.

To reset the panel while the system is operational, for example, prior to reprogramming, press the reset

buttonfor1-2secondswithoutpoweringdownthesystem.Afterresettingthepanel,beginprogramming

within30minutes.Ifyouwaitlongerthan30minutes,youmustresetthepanelagain.

Programming Connection

9.1 Programming Connection

Alocking4-pinheader(PROG)isprovidedtoconnectakeypadwhenusingaDMPModel330Programming

Cable.ThisprovidesaquickandeasyconnectionforprogrammingtheXTLpanel.Afterprogrammingis

complete,removethekeypad.

Note:ThePROGheaderdoesnotprovideaKeypadDataBusconnection.

On-Board 1100 Series Wireless

10.1 Wireless Antenna

TheXTLWirelessAntennaisintegratedintothecircuitboard.TheXTLbuilt-inwirelessreceiveroperates

withDMP1100Seriestransmitters.Seesection3.1foralistofaccessorydevices.

10.2 LED Operation

Green (TX):ThegreenLEDasheseverytimethereceivertransmits(32timespersecond).Ifahousecode

isnotprogrammedinthepanel,thepanelisreset,orthepanelispoweredoff,thegreenLEDisoff.Under

normaloperation,thegreenLEDashesconstantlywithnointerruptionorchange.

Yellow (RX):TheyellowLEDasheseverytimethereceiverhearsamessagefromaprogrammedwireless

transmitter.Whenamessageissentbyatransmitter,typicallybypressingorreleasingthetamperswitch,

theyellowLEDshouldashindicatingthatthereceiverreceivedamessagefromthetransmitter.Ifthe

LEDneverashes,thetransmitterisnotgettingthroughtothereceiver.Thiscouldbebecauseofa

misprogrammedserialnumberorthetransmitteristoofaraway.Undernormaloperation,theyellowLED

ashesateverytripofeverywirelesstransmitterandoccasionallywhenthetransmittersperformtheir

periodiccheck-in.ItisnotunusualforthisLEDtostayoffformanyminutesatatimewhennotransmitters

are communicating.

Tabla de contenidos

Otros manuales de Panel de control de DMP Electronics

DMP Electronics

DMP Electronics XR200 Manual de usuario

DMP Electronics

DMP Electronics XT50 Series Manual de usuario

DMP Electronics

DMP Electronics XTLC Instrucciones de funcionamiento

DMP Electronics

DMP Electronics XT Series Manual de usuario

DMP Electronics

DMP Electronics XR500N SERIES Manual de usuario

DMP Electronics

DMP Electronics XR5FC Instrucciones de funcionamiento

DMP Electronics

DMP Electronics XR550 series Manual de usuario

DMP Electronics

DMP Electronics XT Series Instrucciones de funcionamiento

DMP Electronics

DMP Electronics XR100 Instrucciones de funcionamiento

DMP Electronics

DMP Electronics XT Series Hoja de datos

DMP Electronics

DMP Electronics XR550INT Series Manual de usuario

DMP Electronics

DMP Electronics Addressable Fire Alarm Control Panel XR2500F Manual de usuario

DMP Electronics

DMP Electronics XR150CAN Series Manual de usuario

DMP Electronics

DMP Electronics XTLtouch Manual de usuario

DMP Electronics

DMP Electronics XR150 series Manual de usuario

DMP Electronics

DMP Electronics XR150 series Manual de usuario

DMP Electronics

DMP Electronics XR550 series Manual de usuario

DMP Electronics

DMP Electronics XRSuper6 Manual de usuario

DMP Electronics

DMP Electronics XR200 Instrucciones de funcionamiento

DMP Electronics

DMP Electronics XT30 Series Manual de usuario

DMP Electronics

DMP Electronics XR150FC Series Manual de usuario

DMP Electronics

DMP Electronics XR100 Manual de usuario

DMP Electronics

DMP Electronics XR500 SERIES Manual de usuario

DMP Electronics

DMP Electronics XR6 COMMAND PROCESSOR Instrucciones de funcionamiento

Manuales populares de Panel de control de otras marcas

RDZ

RDZ PC-HRX Manual de usuario

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manual técnico

Efka

Efka Variocontrol V810 Manual de usuario

Cebora

Cebora 208-10 Manual de usuario

AMX

AMX AutoPatch CP-15 Manual de usuario

Satel

Satel CA-6 KLED-S Manual de usuario

Evolution

Evolution IQ plus 800 Manual de usuario

Fagor

Fagor 8040 TCO CNC Manual de usuario

Trane

Trane ComfortLink II XL950 Control Manual de usuario

AKO

AKO PROCool AKO-17635-2 Manual de usuario

ABB

ABB 6136/30M-101 Manual de usuario

Telikou

Telikou BK-603 Belt Pack Manual de usuario

Mapei

Mapei Mapeheat Thermo Touch Manual de usuario

Bosch

Bosch D9412GV4 Manual de usuario

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manual de usuario

Sminn

Sminn BOX L VF1L EI Manual de usuario

Balboa

Balboa TP600 Manual de usuario

Nice

Nice HSCU1 Especificaciones técnicas