Dji DT7 Manual de usuario

- 1 -

DT7&DR16 2.4G RC System User Manual V1.00 

Congratulations on purchasing your new DJI product. Please read this manual carefully to ensure you can get the

most out of it.

*:8KSUZK)UTZXURRKX *88KIKO\KX

Inthe box

DT7 Remote Controller, DR16 Receiver, 3-Pin cable.

Required Items

4 AA batteries, Micro-USB cable, flight control system, multi-rotor etc.

DT7 Remote Controller

The DT7 remote controller is a wireless communication device using the 2.4GHz frequency band. It is only

compatible with the DR16 receiver.

[1]

[2]

[4] [3]

[8]

[9]

J4 [6]

[7]

[5]

]

[10]

[12]

[11]

[1] Antenna [2] Carrying Handle [3] 3-Position Switch S1 [4] 3-Position Switch S2 [5] Stick1 J1;J2

[6] Stick2J3;J4[7] Neck Strap Attachment [8] Power Switch [9] Power LED Indicator

[10] Slide Lever [11] Micro-USB Port [12] Battery Compartment

- 2 -

DR16 Receiver

The DR16 is a 16 channel receiver working at the 2.4GHz frequency band. It is compatible with the DT7 remote

controller.

[1]

[2]

[3]

[7]

[6]

[5]

[4]

[1] Antenna

[2] LED Indicator

[3] Link Button

[4] GND

[5] VCC

[6] DBUS

[7] EXP.

Default Channel Mappings ofDT7&DR16

MODE 1

MODE 2

Slider Lever

Usages ofthe DT7 Remote Controller

Turn onthe remote controller

1. Open the battery compartment on the back of the remote controller.

2. Install 4 AA batteries into the compartment according to the signs of negative and positive poles.

3. Push the power switch to the right to power on the remote controller. If the power LED indicator is solid red, the

remote controller is functioning normally.

4. The remote controller’s antenna should point skywards without obstructions for maximum communication range

during flight.

Turn off the Remote Controller

Push the power switch to the left to power off, the power LED indicator will be out and the remote controller will be

turned off.

Important Notes

lTurn on the remote controller before powering on the aircraft. Power off the aircraft before turning off the

remote controller.

lAvoid interferences between the remote controller and other wireless equipment.

lRemove batteries from the remote controller before long term storage.

lEnsure batteries in the remote controller have enough capacity before every flight.

lDispose of batteries according to their instructions.

- 3 -

Remote controller Power LED Indicator Status Information

Power LED Indicator

Sound

Remote Controller Status

None

Normal

B-B-B……

Low voltage (at 4V-4.3V). Replace the batteries immediately

B--B--B……

Alarm will sound after 15 minutes without activity. It will stop once you

start using the remote controller.

Important: The remote controller will power off automatically when battery voltage drops below 4V. Land and

change batteries as soon as possible when the low voltage alert occurs to avoid loss of control during flight.

Connecting the DR16 Receiver tothe Flight Control System

The DR16 Receiver is designed to be used with the below flight control system. Connect the DR16 receiver to the

correct port on the main controller in the flight control system using a 3-Pin cable, then select the D-BUS receiver

type in the Assistant software.

Flight Control

System

NAZA-M Lite

NAZA-M NAZA-M V2

WooKong-M

Port onthe Main

Controller

X2 X2X2X2X2

Linking the DT7&DR16

1. Power on the main controller and the DR16 receiver.

2. Turn on the remote controller and place the remote controller 0.5m~1m from the receiver.

3. Poke the link button with a thin object and hold it until the LED indicator on the receiver blinks red, then release

it.

4. When the LED indicator becomes solid green, the link between the DT7 remote controller and the DR16 receiver

has been successfully established.

The LED Indicator Status ofDR16

LED Indicator

Status

The remote controller is linked with the receiver successfully

The remote controller is turned off and there is no 2.4GHz signal around

The receiver is ready for linking

There is 2.4GHz signal around but the remote controller is not linked with the

receiver

Usages ofthe RCSYSTEM Assistant software

The RC SYSTEM assistant software is used to configure the DT7 remote controller, upgrade its firmware, select the

sticks mode and calibrate the sticks.

Download & Installation & Connection

1. Download the driver and RC SYSTEM Assistant software, then install the diver and software on your PC.

2. Turn on the remote controller and connect it to the PC by Micro-USB cable.

- 4 -

3. Run the RC SYSTEM Assistant software. Wait for the remote controller to connect to the Assistant software.

When the connection indicator is solid green

and the communication indicator blinks blue , it has connected.

DT7ઁԿ૆ѝ

Firmware Upgrade

1. On the [Info] page, click Latest version to download and install the upgrade following prompts.

2. Power cycle the remote controller after finishing the upgrade. Check the firmware version on the [Info] page, if

Assistant software shows the latest version, upgrade was successful.

Stick Mode Configuration

1. Select your custom control mode in the Stick Mode bar on the [Main] page.

2. Power cycle the remote controller, push both sticks and observe whether the cursors in the respective channels

are moving. This will confirm stick mode configuration.

Sticks Calibration

1. On the [Main] page, click the “Calibration”button to calibrate the sticks following prompts.

2. Calibrate the remote controller after every firmware upgrade or configuration, and calibrate on a regular basis.

DT7&DR16 Specifications

DJI DESSET 2.4G SYSTEM

Operating Frequency

2.4GHz ISM

Communication Distanceopen area

1000m

Remote Controller

General

2-stick, 7-channel

Working Current

100mA@6V

Battery Required

4 AA Batteries

DJI Receiver 16

General

2.4GHz D-BUS System

Receiving Sensitivity1%PER

-97dBm

Working Current

145mA@5V

Power Supply

4~8.4V

Size

41mmX29mmX5mm

Weight

10g

Rechtliche Hinweise

Konformitätserklärung

Hiermit erklärt die Globe Flight GmbH, dass dieses Gerät den produktspezifisch geltenden EU-

Richtlinien entspricht. Durch die Kennzeichnung dieses Gerätes mit dem CE-Symbol wird die

Konformität mit diesen Richtlinien zum Ausdruck gebracht.

Diese RC Funkfernsteuerung verwendet das 2,4GHz ISM-Frequenzband im Bereich

von 2400MHz bis 2483,5MHz (anmelde- und gebührenfrei). Die Einhaltung der

R&TTE-Richtlinien (Radio and Telecommunications Terminal Equipment Directive) ist

mit den entsprechenden Zertifikaten dokumentiert, diese finden Sie entweder an dieses Dokument

angehängt oder zum Download auf unserer Homepage bei der jeweiligen Produktbeschreibung. Das

Gerät ist mit dem CE-Symbol gekennzeichnet, welches auf die Konformität mit den Richtlinien

verweist. Somit darf das Gerät in den Mitgliedsstaaten der Europäischen Union verkauft und

verwendet werden.

Das CE-Symbol beinhaltet weiterhin die Richtlinie 2002/95/EG des Europäischen Parlaments und des

Rates über die Beschränkung der Verwendung bestimmter gefährlicher Stoffe in Elektro- und Elektro-

und Elektronikgeräten (sog. RoHS).

WEEE-Registrierungsnummer: DE 52086694

Hierbei handelt es sich um die Einhaltung der Richtlinie 2002/96/EG des Europäischen Parlaments

und des Rates über Elektro- und Elektronik-Altgeräte (sog. WEEE) zur Reduktion der zunehmenden

Menge an Elektroschrott.

Entsorgung elektrischer und elektronischer Geräte

Dieses Gerät darf nicht über den Hausmüll entsorgt werden! Bitte suchen Sie hierfür eine

kommunale Sammelstelle oder einen Recyclinghof auf.

Entsorgung von Batterien

Dieses Gerät enthält einen Lithium-Polymer-Akku. Dieser darf keinesfalls über den

Hausmüll entsorgt werden! Bitte suchen Sie hierfür eine kommunale Sammelstelle oder

einen Recyclinghof auf. Gemäß Batterieverordnung sind auch Fachhändler und Hersteller

zur Rücknahme und Entsorgung verpflichtet.

Ansprechpartner / Importeur

Globe Flight GmbH

- vertreten durch Geschäftsführer Sebastian Seidel -

Borsigstrasse 9

93092 Barbing

Deutschland

Tel: +49 9401 949 88-88

www.globe-flight.de

Die in dieser Anleitung enthaltenen Informationen wurden sorgfältig überprüft. Dennoch kann für

inhaltliche Fehler, Druckfehler und Unvollständigkeiten keinerlei Haftung übernommen werden.

Technische Änderungen vorbehalten.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Mando a distancia de dji

dji

dji Cendence Manual de usuario

dji

dji A3 Manual de usuario

dji

dji RC Motion 2 Manual de usuario

dji

dji Focus Manual de usuario

dji

dji FOCUS CP.ZM.000238.02 Manual de usuario

dji

dji Focus Manual de usuario

dji

dji LIGHTBRIDGE Manual de usuario

dji

dji SPARK REMOTE CONTROLLER C2 Manual de usuario

dji

dji Smart Controller Manual de usuario

dji

dji Focus Manual de usuario

dji

dji DT7 Manual de usuario

dji

dji Matrice600 Series Manual de usuario

dji

dji OSMO ACTION Manual de usuario

dji

dji RC Pro Manual de usuario

dji

dji FPV AIR UNIT Manual de usuario

dji

dji Cendence Manual de usuario

dji

dji SPARK REMOTE CONTROLLER C2 Manual de usuario

dji

dji PVT581 Manual de usuario

dji

dji Smart Controller Enterprise Manual de usuario

dji

dji RC Plus Manual de usuario

dji

dji A3 Manual de usuario

dji

dji RC Motion 2 Manual de usuario

dji

dji FPV Remote Controller 2 Manual de usuario

dji

dji RC Manual de usuario

Manuales populares de Mando a distancia de otras marcas

Panasonic

Panasonic EUR7622KB0 Manual de usuario

Bang & Olufsen

Bang & Olufsen Beo4 Manual de usuario

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manual de usuario

Multiplex

Multiplex PROFI TX 9 Manual de usuario

One Remote

One Remote RMB4 Manual de usuario

FUTABA

FUTABA 9ZAP - PART2 Manual de usuario

HR Matic

HR Matic HR MULTI 3 Manual de usuario

Yamaha

Yamaha ACC-GNRST-30-20 Manual de usuario

EisSound

EisSound KBSOUND Manual de usuario

Marantz

Marantz RC101 Manual de usuario

Conrad

Conrad FS20 TC6 Manual de usuario

Anritsu

Anritsu MP1777A Manual de usuario

Niles

Niles WVC100 Guía de solución de problemas

RCA

RCA RCU1300 Manual de usuario

Bang & Olufsen

Bang & Olufsen BEO6 Manual de usuario

GE 94901 Manual de usuario

Onbon

Onbon YQ1-75 Manual de usuario

FUTABA

FUTABA R7108SB Instrucciones de instalación