dji GOGGLES INTEGRA MOTION COMBO Manual de usuario
User Manual
2023.03v1.0
2 ©2023 DJI All Rights Reserved.
Searching for Keywords
Search for keywords such as “battery” and “install” to nd a topic. If you are using
Adobe Acrobat Reader to read this document, press Ctrl+F on Windows or Com-
mand+F on Mac to begin a search.
Navigating to a Topic
View a complete list of topics in the table of contents. Click on a topic to navigate to
that section.
Printing this Document
This document supports high resolution printing.
©2023 DJI All Rights Reserved. 3
Using this Manual
Legend
Important Hints and Tips
Before Flight
It is recommended to watch all tutorial videos and read the safety guidelines before using
for the rst time. Prepare for your rst ight by reviewing the quick start guide and refer-
ring to this user manual for more information.
5.8 GHz is not supported in some regions. This frequency band will automatical-
ly be disabled when the aircraft is activated or connected to the DJI™ Fly app in
these regions. Observe local laws and regulations.
Using the goggles does not satisfy the requirement of visual line of sight (VLOS).
Some countries or regions require a visual observer to assist during ight. Make
sure to comply with local regulations when using the goggles.
Video Tutorials
https://www.dji.com/goggles-integra/video
Download the DJI Fly App
https://www.dji.com/goggles-integra/downloads
Download DJI Assistant 2 (Consumer Drones Series)
https://www.dji.com/goggles-integra/downloads
4 ©2023 DJI All Rights Reserved.
Table of Content
Using this Manual 3
Legend 3
Before Flight 3
Video Tutorials 3
Download the DJI Fly App 3
Download DJI Assistant 2 (Consumer Drones Series) 3
Overview 6
DJI Goggles Integra 6
DJI RC Motion 2 7
Getting Started 9
Preparing the Goggles 9
Preparing the Motion Controller 13
Activation 14
Linking 15
Wearing the Goggles 17
DJI Goggles Integra 18
Operating the Goggles 18
Goggles FPV View 18
Shortcut Menu 20
Camera Settings 21
Goggles Menu 22
Sleep Mode 25
Footage Storage and Export 25
Formatting the microSD Card 26
Screen Masking 26
Using the Head Tracking Function 26
Switching Aircraft 26
DJI RC Motion 2 27
Controlling the Aircraft 27
Controlling the Camera 29
Motion Control 30
Motion Controller Alert 31
Motion Controller Calibration 31
6 ©2023 DJI All Rights Reserved.
Overview
DJI Goggles Integra (hereinafter referred to as goggles) is equipped with two high-perfor-
mance screens and ultra-low latency image transmission for use with DJI aircraft, giving
a real-time aerial FPV (First Person View) experience. When used with the DJI RC Motion 2
(hereinafter referred to as motion controller), users can easily and intuitively control the
aircraft.
DJI Goggles Integra
1. Antennas
2. microSD Card Slot
3. 5D Button
Press down or toggle to the right to open the menu from the FPV view of the goggles.
Toggle the button forward to open the camera settings panel and toggle backward to
open the shortcut menu.
After the settings panel is opened, toggle the button to navigate the menu or adjust
the parameter value. Press the button to conrm the selection.
4. Back Button
Press to return to the previous menu or exit the current view.
5. Headband
The battery wires are embedded in the headband. DO NOT pull the headband
with force to avoid damaging the wires.
6. Battery Compartment
7. Headband Adjustment Knob
Rotate the knob to adjust the length of the headband.
8. Foam Padding
1
6
7
5
12
11
2
3
49
10
8
DJI Goggles Integra Motion Combo User Manual
©2023 DJI All Rights Reserved. 7
DJI RC Motion 2
1
2
6
7
3
8
49
5
9. Battery Level LEDs
10. Power Button/Link Button
Press once to check the current battery level.
Press, and then press and hold to power the goggles on or o.
When powered on, press and hold the button to initiate linking.
11. USB-C Port
For charging, connecting headphones, or connecting the goggles to a computer.
Only supports Type-C headphones and headphone adapters with built-in DAC
(digital-to-analog converter).
It is recommended to use the USB-C OTG cable provided and a USB-A to USB-C
cable to connect the goggles to a mobile device.
The goggles do not support computer connection using a USB-C to USB-C cable.
12. IPD (Interpupillary Distance) Slider
Slide left and right to adjust the distance between the lenses until the image is proper-
ly aligned.
1. Battery Level LEDs
2. Lock Button
Takeo: press twice to start the aircraft motors, then press and hold to make the air-
craft take o. The aircraft will ascend to approximately 1.2 m and hover.
Landing: while the aircraft is hovering, press and hold to land the aircraft and stop the
motors.
10
DJI Goggles Integra Motion Combo User Manual
8 ©2023 DJI All Rights Reserved.
Brake: press once to make the aircraft brake and hover in place. Press again to un-
lock the attitude.
When the aircraft is performing RTH or auto landing, press the button once to can-
cel RTH or landing.
3. Joystick
Toggle up or down to make the aircraft ascend or descend. Toggle left or right to
make the aircraft move horizontally left or right.
4. Mode Button
Press to switch between Normal and Sport mode. Press and hold to initiate RTH.
Press again to cancel RTH.
5. FN Dial
Press the dial to open the camera settings panel in the FPV view. Scroll the dial to
navigate the settings menu or adjust the parameter value, then press the dial to
conrm the selection. Press and hold the dial to exit the current menu.
The FN dial can also be used to control the camera tilt before takeo or during RTH
and landing. Press and hold the FN dial from the FPV view and then scroll up or
down to tilt the camera. Release the dial to stop the camera tilt.
6. Shutter/Record Button
Press once: take a photo or start/stop recording.
Press and hold: switch between the photo and video modes.
7. Accelerator
Press to y the aircraft in the direction of the circle in the goggles. Push forward to
y the aircraft backward. Apply more pressure to accelerate. Release to stop and
hover.
8. USB-C Port
9. Power Button/Link Button
Press once to check the current battery level.
Press, and then press and hold to power the motion controller on or o.
When powered on, press and hold the button to initiate linking.
10. Lanyard Hole
©2023 DJI All Rights Reserved. 9
Getting Started
This chapter helps users with rst time use.
Preparing the Goggles
Installing the Corrective Lenses
The goggles are equipped with a pair of eyeglass frames and come with 10 pairs of vision
corrective lenses (from -8.0 diopter to +2.0 diopter, without astigmatism correction) and
one pair of plain lenses (0 diopter). Users can install suitable lenses according to their ac-
tual eyesight.
Even if vision correction is not necessary, it is strongly recommended to install
the plain lenses to protect the goggles screen glasses from being scratched.
If astigmatism correction is needed or the provided lenses are not suitable, us-
ers can purchase additional lenses. When purchasing lenses, take the eyeglass
frames (a pair) and a pair of lenses to a professional optician to ensure that the
shape, size, astigmatism axis, and edge thickness (< 2.8 mm) of the lenses meet
the installation requirements of the eyeglass frames.
1. Detach the eyeglass frames from the goggles (no need to rotate the frames). Turn over
the frames and identify the shortest line mark (a), the longest line mark (b), and the
side line mark (c), as shown in the diagram below.
2. Take out the suitable lenses from the package. The diopter of the lenses is printed on
the inside of the lens box lid and also marked on the edge of each lens. Identify the
shortest cut edge (a), the longest cut edge (b), and the side cut edge (c), as shown in
the diagram below.
a
a
-7D
-8D -5D-6D -3D-4D -1D
-2D +1D
0D
+2D
DJI Goggles Integra Motion Combo User Manual
10 ©2023 DJI All Rights Reserved.
3. Distinguish the left and right frames and the corresponding lens, then install the lenses
into the frames. Make sure that the shortest cut edge (a), the longest cut edge (b), and
the side cut edge (c) of the lens are aligned with the corresponding line marks on the
frame respectively. For easier installation, align and insert the longest edge (b) first.
Make sure the lens is installed in place and not tilted. If the cut edges of the lens are
not properlly aligned with the frame line marks, the lens will not fit into the frame.
Clean the lens with the provided cleaning cloth to wipe off the fingerprints and dust
after installation.
4. Mount the lens-installed frames onto the goggles (no need to rotate the frames). When
installing, make sure that the letter L/R on the top of the frame is facing upwards and
that the positioning mark on the frame is aligned with the positioning mark on the
goggles.
a
a
a
b
Tabla de contenidos
Otros manuales de Accesorios de dji
dji
dji FPV GOGGLES Manual de usuario
dji
dji D-RTK Manual de usuario
dji
dji Goggles RE Manual de usuario
dji
dji INSPIRE 2 Manual de usuario
dji
dji NAZAH Manual de usuario
dji
dji Goggles Manual de usuario
dji
dji FPV Goggles V2 Manual de usuario
dji
dji Goggles Manual de usuario
dji
dji GOGGLES 2 MOTION COMBO Manual de usuario
