DIY Security Cameras Hikvision Manual de usuario
DIY Security Cameras
Hikvision
Intercom Setup Guide
September 2017
Prepared by
DIY Security Cameras
23rd September 2017
Hikvision Intercom Setup Guide (v1.0) September 2017
DIY Security Cameras (www.diysecuritycameras.com.au) Page 2
Contents
2INTRODUCTION .......................................................................................................................................................... 3
3EQUIPMENT .................................................................................................................................................................. 3
4PRE-REQUISITES ......................................................................................................................................................... 3
4.1NETWORK WORKSHEET ............................................................................................................................................ 3
4.2FIRMWARE ................................................................................................................................................................ 3
4.3IVMS4200 SOFTWARE ............................................................................................................................................. 3
4.4PC/LAPTOP ............................................................................................................................................................ 3
5CONFIGURE IVMS4200 SOFTWARE ....................................................................................................................... 4
6ACTIVATE INTERCOM DEVICES ........................................................................................................................... 6
6.1DOOR STATION ......................................................................................................................................................... 7
6.2INDOOR STATION ...................................................................................................................................................... 9
7ASSIGN IP ADDRESS TO INTERCOM DEVICES ................................................................................................ 12
7.1DOOR STATION ....................................................................................................................................................... 12
7.2INDOOR STATION .................................................................................................................................................... 14
7CONFIGURATION AND SETUP OF INTERCOM DEVICES .............................................................................. 17
7.1DOOR STATION ....................................................................................................................................................... 17
7.2MASTER INDOOR STATION ...................................................................................................................................... 20
7.3EXTENSION INDOOR STATION ................................................................................................................................. 23
8VALIDATION .............................................................................................................................................................. 25
Hikvision Intercom Setup Guide (v1.0) September 2017
DIY Security Cameras (www.diysecuritycameras.com.au) Page 3
2 Introduction
This guide will take you through the steps to setup a Hikvision Video Intercom system for a single dwelling with 2 x Indoor
Room Stations and 1 x Villa Door Station. This assumes that the Intercom devices are at factory default settings and need to
be activated.
3 Equipment
1 x KAD606 – Video/Audio Distributor
2 x DS-KH8301-WT – Indoor WiFi station
1 x DS-KV8102-IM – Villa Door Station
1 x PC/Laptop running iVMS4200 2.4.5.X
4 Pre-Requisites
4.1 Network Worksheet
Before we begin we need to plan out our network IP addresses to be assigned to each of the intercom components to provide
connectivity. Any IP subnet can be used, however note that there can only be a maximum of 9 villa door stations in one
system, so leave enough address space to cater for this if required.
In our example we are going to use 192.168.20.0/24 subnet as per the table below.
Device
Type
Local IP Subnet Mask Gateway Door Station
IP
SIP Server Main Door
Type
Main Door V Series 192.168.20.100 255.255.255.0 192.168.20.254 N/A N/A V Series
Master Indoor
Station
Indoor
Station 192.168.20.110 255.255.255.0 192.168.20.254 192.168.20.100 192.168.20.100 N/A
Extension
Indoor Station
Extension
Station 192.168.20.111 255.255.255.0 192.168.20.254 N/A N/A 192.168.20.110
4.2 Firmware
The minimum firmware release for the intercom system is v1.4.0 Build 170302. Please ensure this version of firmware is
installed before proceeding with the remaining setup. To obtain the firmware please email us at
support@diysecuritycameras.com.au. Note we can only supply firmware to our customers.
4.3 iVMS4200 Software
You will need to install the iVMS4200 software version 2.4.2.55 build161209 onto your laptop. This is required for this
version of the firmware.
4.4 PC/LAPTOP
A Windows PC/Laptop is required to run the iVMS4200 software to programme and setup the Intercom system. The PC in
our example should be connected directly to the KAD LAN2 port. Initially the default factory IP address for the Intercom
devices are: 192.0.0.64/24 (255.255.255.0) and 192.0.0.65/24 (255.255.255.0)
To allow the PC to communicate with the Intercom devices, configured the PC with a primary IP address of 192.168.20.150
(in our example) and a secondary IP address of 192.0.0.250. If you are not sure how to setup a secondary IP address, Google
is your friend.
Hikvision Intercom Setup Guide (v1.0) September 2017
DIY Security Cameras (www.diysecuritycameras.com.au) Page
4
5 Configure iVMS4200 Software
The iVMS4200 (version 2.4) software by default only shows Intercom door stations. To setup and configure Indoor stations
the device type needs to be added to iVMS4200.
1. Click on Device Management.
2. Click on “Add New Device Type”
3. Select “Indoor Station/Master Station” and click OK
4. You should now see “Indoor Station/Master Station” in the left hand menu.
Hikvision Intercom Setup Guide (v1.0) September 2017
DIY Security Cameras (www.diysecuritycameras.com.au) Page
5
Hikvision Intercom Setup Guide (v1.0) September 2017
DIY Security Cameras (www.diysecuritycameras.com.au) Page
6
6 Activate Intercom Devices
All Intercom devices need to be activated (ie with a strong password) before being configured for use. Activation can be
done via the iVMS4200 software tool.
Notes around the activation password
a. Please make this a strong password.
b. The activation password is the main admin configuration/setup password.
c. This password is need to do any configuration on the Intercom devices via the iVMS4200 software.
d. This password is different to the indoor station “admin” password, which can be set separately.
Plug in all the Intercom devices as per above diagram and they will booted up and power on. When powered on they will
appear at the bottom in “Online Devices” section of the iVMS4200 software.
Hikvision Intercom Setup Guide (v1.0) September 2017
DIY Security Cameras (www.diysecuritycameras.com.au) Page
7
Now we activate the devices individually.
6.1 Door Station
1. Select Encoding Device/Door Station
2. Select Door Station at the bottom of the screen and click “Activate”
Hikvision Intercom Setup Guide (v1.0) September 2017
DIY Security Cameras (www.diysecuritycameras.com.au) Page
8
3. Enter a strong password for the door station and click “OK”
4. Device should now show as active.
Hikvision Intercom Setup Guide (v1.0) September 2017
DIY Security Cameras (www.diysecuritycameras.com.au) Page
9
6.2 Indoor Station
1. Select Indoor Station/Master Station in left Menu
2. Select Indoor Station at the bottom of the screen and click “Activate”
Hikvision Intercom Setup Guide (v1.0) September 2017
DIY Security Cameras (www.diysecuritycameras.com.au) Page
10
3. Enter a strong password for the indoor station and click “OK”.
4. Device should now show as active
Tabla de contenidos
