Discountcomms WT2002 Manual de usuario

GSM Single Display Payphone

WT2002

User Manual

www.discountcomms.co.uk

WT2002 GSM Single Display Payphone

Contents

Caution, Storage, Basic Features…

……………………………………………………….…... 3

I. The sketch of telephone

……………………………………………………………………...4

II. Install SIM card

…………………………………………………………………….…..….5

III. Power on

…………………………………………………………………………….……5

IV. Power off

…………………………….…………………………………………………... 6

V. Menu Tree...

………………………………………………………………………………..6

1. Select gateway…………………………………………………………………………...7

2. Make calls………………………………………………………………………………7

3. Force the dialed telephone number to be transmitted direct

………………………………………………....

Receive incoming calls

……………………………………………………………………………….....

Read, forward and delete short messages

……………………….. ………………………………………..

Writing and sending short message

………………………………………………………………………

Notes: the edit of short message………………………………………………………………………………..... 12

Inquire the dialed calls and the information for sent message

……………………………………………...

10. Inquire information for received calls……………………………………………………………………..…….13

Inquire missed calls

……………………………………………………………………………………

12. Inquire call charge statistics……………………………………………………………………………………. 14

13. Clear call lists…………………………………………………………………………………………………... 15

14. Clear call statistic………………………………………………………………………………………………. 15

15. Telephone book………………………………………………………………………………………………… 16

16. Hot keys………………………………………………………………………………………………………... 17

17. Menu keypad tones…………………………………………………………………………………………….. 17

18. Ringing tones level…………………………………………………………………………………….……….. 17

19. Settings……………………………………………………………………………………………….…………18

I. Enter the Settings Procedures……………………………………………………………………………………..18

II. Setup the phone parameters……………………………………………………………………………...………18

1. Modify Setup information…………………………………………………………………………….…….18

2. Short Message Centre setup…………………………………………………………………………...……19

3. Network Management System Centre Setup..........................................................................................…...20

4. Set-up Prefix for Barred No……………………………………………………………………………..….20

5. Set-up for IDD Prefix, DDD Prefix, LOCAL Prefix and Mobile Phone Prefix…………………………....21

6. Setup for Tariff and GNP……………………………………………………………………………...……22

7. Change Owner Pin..................................................................................................................................…...26

8. Setup Currency Types……………………………………………………………………………...……….26

9. Setup Date & Time..................................................................................................................................…...27

10. Set up the Gateway Number and parameter.........................................................................................…...27

20. Inquire IMEI code and software version and hardware version……………………………………..………….31

21. Change User Pin………………………………………………………………………………………….……..32

22. Lock keyboard for charging from the customers………………………………………………………….…….32

25. Setup local phone number…………………………………………………………………………….…………32

VIII. Appendix……………………………………………………………………………………………...

1. Technical Specification………………………………………………………………………………………........34

2. Troubleshooting…………………………………………………………………………………………………...34

www.discountcomms.co.uk

WT2002 GSM Single Display Payphone

Caution:

1. This phone should not be used at garage, oil storage, chemical plant or near to any inflammable or

explosive substance.

2. This telephone should be avoided in the hospital. It will interfere with medical electronic equipments

such as pacemaker and audiphones.

3. If it is found that the telephone is not successful in login onto network, please check whether the SIM

card or antenna is well installed.

4. The telephone does not identify the old SIM card of 5V and 1.8V.

5. It is forbidden to touch the antenna when the phone is being used. (Being making calls or receiving

calls), otherwise the telephone will be damaged. This kind of damage is beyond the range of warranty.

6. When the telephone is being used, it should be placed where signal is strong enough. In order to ensure

good voice quality, the telephone should be far from other electronic equipment.

7. Don’t use chemic substance to clean the telephone, but use dry soft cloth to clean it.

8. Don't disassemble the telephone by yourself. If there is any problem, please contract the authorized

personnel.

Storage:

1. The telephone that is packed or not could piled up no more than 10 layers.

2. The telephone should be saved in the ventilate and dry place.

3. Don’t knock the telephone to avoid breaking the case.

Basic Features:

1. For making calls, the users can lift the handset or press “Hand Free” button, the LCD will shows

“PRESS OK TO REDIAL”, then dial upon hearing the dialing tone. When LCD shows “PRESS OK

TO REDIAL”, press “OK” key and the phone will dial the last dialed numbers.

2. During a call, press “UP” or “DOWN” key to adjust the voice volume. While pressing “Hand Free”

during a call will disconnected the call.

3. When there is incoming calls, the telephone rings and displays the incoming call number Lift the

telephone or press “Hand Free” to answer it. Press “CANCEL” to reject the calls.

4. Press “MENU” key to go into the list of menu.

5. After enter menu, press “UP” key and “DOWN” key to scroll the content you are viewing, press “OK”

key to confirm your operation, press “BACK” key to cancel your operation and return to the previous

menu. During the edit of the input, press “CANCEL” key to cancel the last character of the inputting

line, press “DELETE” key to delete the whole inputting line.

6. Press the corresponding key to enter the entry of menu. For example, for menu “4:PHONE BOOK”,

Press “4” key to enter “PHONE BOOK”.

7. For selecting gateway, press “GATEWAY” key will display the list of gateways. Press “F1” and “F2”

to scroll up and down the list of gateways, then press “CONFIRM” to select the gateway.

www.discountcomms.co.uk

WT2002 GSM Single Display Payphone

I. The sketch of the telephone

Hand-Free

TheFacadeOfthePhone

BottomOfthePhone

WT2002 GSM Single Display Payphone

II. Install SIM card

1. Screw off the screw of SIM card case, and open the cover.

2. Slide back the SIM card door and lift it up.

3. Slide the SIM card into the SIM door making sure that the clipped corner of the SIM card lines

up with the clipped corner of the SIM holder.

4. Close the SIM card door and slide it to lock the SIM card in place.

5. Replace the cover of SIM card case and fixes it with a screw.

III. Power on

Connect the input end of the power adapter to main power socket, and the output end connects to the

power supply port of telephone. The telephone begins to search for the network, and the LCD shows

“SEARCHING FOR NETWORK”, “INITIALIZATION”, “READ SIM PHONEBOOK” in turn.

When the LCD shows icons operator name, time and the signal, etc., login is finished.

When the telephone is connected to external power supply through power adapter, LCD displays as

follows:

“NETWORK NAME”

STANDBY

01/01/2000 01:40

When there is no external power supply and batteries are being used, the icon ‘ ’ with be replaced by the icon

‘ ’

“NETWORK NAME”

STANDBY

01/01/2000 01:40

Signal is good

Time

Name of service provider

Power adapter is being used

Date

Status of the telephone

Signal is weak

Batteries are being used

WT2002 GSM Single Display Payphone

“NETWORK NAME”

01/01/2000 01:40

Notice: Please recharge the battery when the warning icon for batteries appears. Otherwise the telephone will

be halted. Then all the telephone’s functions will be ended. If the telephone has been halted, please

connect the telephone to external power supply and push the switch to “ON” side, the telephone will

work normally.

IV. Power off

Shut off the main power and push the power switch to “OFF” side, the telephone will be turned off and the

LCD is cleared.

V. Menu Tree

NOTICE: In main menu, users can’t enter “SETTINGS” menu unless input the correct setting password..

In “CALL REGISTER” menu, user’s password is valid for erasing “CALL LISTS”, erasing

“CALL STATISTICS”, “Reset Accumulated Charges” and “Menu-Locking” enable and

disable. Please notice that user’s password and setting password are not the same. The default

settings password is “30459086” and the default user’s password is “64139025”

No signal

It is failed for the

telephone to logon on

networ

Warning icon for too low

voltage of batteries

1: READ MESSAGES

2: WRITE MESSAGE

3: CALL REGISTER

4: PHONE BOOK

5: KEYPAD TONES

6: RINGING TONES

7: SETTINGS

8:IMEI-VERSION

9: CHANGE USER PIN

0: MENU-LOCK ENABLE

*: PRINT OPTION

#: LOCAL PHONE NO.

BACK:BACK

1:DIALED NUMBERS

2:RECEIVED CALLS

3:MISSED CALLS

4:CALL STATISTICS

5:ERASE CALL LISTS

6:ERASE STATISTICS

BACK:BACK

LOCK SETTING

SMS CENTRE

NMS CENTRE

PREFIXED NO.

TARIFF TABLE

CHANGE OWNER PIN

CURRENCY SETTING

DATE AND TIME

GATEWAY SETTINGS

BACK:BACK

WT2002 GSM Single Display Payphone

1. Select gateway

a) In standby status, press “Gateway” the LCD display as following

SELECT GATEWAY

NO.1 12345678

b) Press “F1” and “F2” to select gateway. Press “CONFIRM” to save the selection.

NO.1 is the serial code of the gateway and “12345678” is gateway’s number. If the number of

gateway is not setup, “<NULL>” will be shown replacing “12345678”.

2. Make calls

a) Lift the handset or press “Hand Free” button, the LCD shows “PRESS OK TO REDIAL”, dial

upon hearing the dialing tone

b) On completion of dialing digits, press “OK” to send the dialed telephone number. If there is no

dialing for continuous 6 seconds, and the dialed number is 2 digits or is more than 2 digits, the

telephone will send out the number automatically. The LCD shows number sending indication. If

the number dialed is less than 2 digits and there is not any dialing for continuous 6s, the

telephone will return to standby status.

CALLING …

12345678

c) If the dialed number is a barred one, the LCD shows “BARRED NO.” and returns to standby

status.

BARRED NO.

12345678

NETWORK NAME

STANDBY

01/05/2005 15:12

WT2002 GSM Single Display Payphone

c) If the dialed number is transmitted directly and gateways aren’t been used, the telephone starts

timing and recording charge for the call as soon as the called is answered. If the dialed number is

transmitted through gateway, the LCD displays “CALLING GATEWAY X”, “CONNECTED

GATEWAY”, “SENDING PASSWORD” in turn. When the gateway is connected, LCD

displays “SENDING CALLED NO.”, “SENDING #” to send the dialed number, and then

“PRESS F1 TO SPEAK” will be displayed. When the dialed part answers the call, press

“REPORT”, the phone start timing and recording charges. The LCD displays accumulated call

times “XX”, the tariff “XX.XX/XXs”, current call charge “USD：XX.XX”, call duration

“h:mm:ss” and accumulated call charge “FEE:XX.XX”.the as following example.

0.00/60s USD: 0.00

0:00:12 FEE: 3.00

12345678

•During a call, press the numeral key or “*” or “#” to output corresponding Dual Tone

Multiple Frequency (DTMF);

•During a call, press “Up” or “Down” to adjust volume.

d) Flap hook unit or press “Hand Free”, the line will be disconnected.

3. Force the dialed telephone number to be transmitted direct.

If the customers want to transmit their dialed call direct and don’t use gateway, they can press “11”

before pressing their telephone number. For example, the telephone number the customer wants to

dial is 87654321 and it is setup to be transmitted through gateway, the customer should dial

1187654321.

4. Receive incoming calls

a) When there is incoming calls, the telephone rings and displays the incoming call number Lift the

telephone or press “Hand Free” to answer it. Also you can press “Cancel” to reject it.

12345678

b) When the call is connected, the telephone begins timing and recording charges bill. The LCD

shows accumulated call times “XX”, the tariff “XX.XX/XXs”, current call charge “USD：

XX.XX”, call duration “h:mm:ss” , and accumulated call charge “FEE:XX.XX”.

WT2002 GSM Single Display Payphone

0.00/60s USD: 0.00

0:00:12 FEE: 3.00

12345678

c) During a call, press “Up” or “Down” to adjust the volume;

d) If there is an incoming call and its number isn’t displayed on LCD, when it is being answered,

the incoming call number will be displayed as “0000”.

5. Read, forward and delete short messages

When a short message is received, the phone will send out a short ring tone to indicate the arrival of

the new short message. The icon “ ”will be displayed on the LCD.

a) Press “1” to enter menu “1:READ MESSAGES” to read short message lists.

1:READ MESSAGES 01/03

2:WRITE MESSAGES

3:CALL REGISTER j

b) Press “Up” and “Down” to select the short message the users want to read. The selected

one will be market with “→” on the left.

→01: SMS UNREAD

02: SMS READ

03:SMSREAD j

c) Press “OK” to read it.

d) Press “Up” and “Down” to look through the short message and the correlative information, such

as the sender’s telephone number, sending date and sending time.

e) Press “OK” to enter reply and forward menu.

f) Press “1” to enter the edit of the replying short message. When the short message is not empty,

press “OK”, the LCD displays as follows.

1. REPLY

2. FORWARD

0. BACK

WT2002 GSM Single Display Payphone

i) Press “OK”, the LCD display as follows.

ii)

Press “OK” to send short message, press “Back” to return to the edit of short message.

g) Press “2” to enter the edit of the short message that the users want to forward. On the completion

of edit, press “OK” to send it.

h) In short message lists status or when short message is read, press “Cancel” or “Delete” to delete

message. The LCD will display as follows.

Press “0” to cancel the operation and return to short message lists. Press “1” to confirm the

delete operation and return to short message lists.

6. Writing and sending short message

Users can write a message that is not longer than 160 English characters, each line for the text area

can input of 20 characters. Short message center must be set up for sending or receiving short

message. (Please refer to Settings below on page 19 for SMS center setting).

1:READ MESSAGES 00/02

2:WRITE MESSAGES

3:CALL REGISTER j

SEND TO：

12345678

SEND？

YES：OK N0：BACK

ERASE MESSAGES

0: NO 1: YES

MESSAGES ERASED

Tabla de contenidos

Manuales populares de Teléfono de otras marcas

GE 2-9480 Manual de usuario

Geemarc

Geemarc PHOTOPHONE 155 Manual de usuario

D-Link

D-Link DWR-720/PW Manual de usuario

Interquartz

Interquartz Gemini IQ333 Manual de usuario

SSS Siedle

SSS Siedle HT 840-0 Manual de usuario

Motorola

Motorola TITANIUM Manual de usuario

Panasonic

Panasonic ICX Manual de usuario

LG H870DS Manual de usuario

Samsung

Samsung GT-I9500 Manual de usuario

AT&T

AT&T Trimline 205 Manual de usuario

Selta

Selta zenyth 600 Manual de usuario

Doro

Doro AFTI 20 Manual de usuario

UNIQCELL

UNIQCELL A1 Manual de usuario

Panasonic

Panasonic KX Series Manual de usuario

Jabra

Jabra SP5050 - Bluetooth hands-free Speakerphone Manual de usuario

BT Decor 425 Manual de usuario

NEC

NEC SV8500 Manual de usuario

Teledex

Teledex PEARL Manual de usuario