Directive Systems & Engineering DSE2455LYK Manual de usuario

DSE2455LYK Rev 4/21

Directive Systems & Engineering

2702 Rodgers Terrace

Haymarket, VA 20169-1628

www.directivesystems.com

703-754-3876

24cm Loop Yagi Kit, Model DSE2455LYK (w/sub-boom)

SPECIFICATIONS

Frequency range: 1.24 to 1.27 GHz Gain: ≅21 dBi

Number of elements: 55 3 dB Beamwidth

Boom length: 180 inches (E plane): ≅14º

Boom diameter: 1 inch F/B ratio: >20 dB

Mast diameter: 2 inch max Maximum Power: 550 W average

Weight: (assembled) 7 pounds Stacking distance: 26 inches’ vertical

Connector: Type-N female 29 inches’ horizontal

PARTS LIST

Note: All hardware is Stainless Steel unless otherwise noted.

Anti-Seize Compound - Apply a small amount of the supplied Anti-Seize Compound to the aluminum joints and

to the threads of the U-Bolts to prevent galling.

CAUTION: While we strive to remove all burrs from all machined parts, there is always the possibility of

sharp edges. We strongly suggest checking the edges and use a fine file, or 400 grit sandpaper,

to remove any burrs that may have been left.

Quantity Description Quantity Description

3 .058" x 1" drilled boom 55 4-40 x 1 1/4” screw

1 74 1/4" x 3/4" square sub-boom 56 4-40 lock nut

2 sub-boom brackets 4 8-32 x 1/2” screw

2 sub-boom plates 88-32 x 1 1/4” screw

1reflector 1 (1/4”) 48-32 x 1 3/8” screw

1reflector 2 (3/8”) 28-32 x 2” screw

1 driven element 18 #8 hex nut

4 directors 1-4 (1/4" wide) 18 #8 Split Lock Washer

7 directors 5-11 1 boom to Mast Bracket

6 directors 12-17 1 boom to Mast Plate

6 directors 18-23 2 2" U-bolt with nuts & lock washers

12 directors 24-35 2 saddles

7directors 36-42 1 cable assy w/connector

10 directors 43-52 1Anti-Seize Compound

2 1" Black End Cap

1 Assembly Manual

P a g e | 2

DSE2455LYK Rev 4/21

BEFORE INSTALLING YOUR NEW ANTENNA, PLEASE BE SURE

TO READ THE ENCLOSED WARNING PAMPHLET.

(Can be up or down) (Can be left or right)

ASSEMBLY INSTRUCTIONS

1) Slide the three boom sections together, matching the colors at each splice connection.

Temporarily secure the booms with a 4-40 x 1 ¼” screw and lock nut at each boom splice.

2) Attach loops to the boom with 4-40 screws and lock nuts in proper sequence. Loops go

on the side of the boom marked with an "X". Attach the contents of each bag of elements

before opening the next bag. This will prevent any mix-up of elements on the boom. R2

(Reflector 2 -3/8" wide) is always the first element to be installed with R1 (Reflector 1 -1/4"

wide) always next to the driven element. When tightening the nuts on the parasitic directors,

be careful not to torque them too tightly. Snug down the nuts, align the elements and use a

screwdriver for final tightening. A 1/4" nut driver is almost mandatory for this job! Attach the

brass driven element with the 5/16" nut provided. If only a single antenna is being built, it does

not matter which way the loop is oriented. If antennas are to be stacked, see "Instructions for

Stacking Loop Yagis".

Refer to photos on the next few steps for clarification.

3) Mount the boom to mast bracket (square tubing piece) to the center boom section,

using 8-32 X 2" screws, lock washers and nuts. Mount the boom to mast plate to this bracket

using 8-32 x 1 ¼” screws, lock washers and nuts. Note: There may be extra holes in the plate that

may be used for different applications.

4) There are two sub-boom brackets consisting of ½” aluminum angle and sub-boom

plates. Mount the angle brackets on the front and rear boom sections using 8-32 x 1 3/8”

screws, lock washers and nuts. Mount the sub-boom plates to these brackets using 8-32 x ½”

screws, lock washers and nuts.

5) Mount the sub-boom (3/4” thick wall aluminum square tubing) to the sub-boom brackets

and boom to mast plate using 8-32 x 1 ¼” screws, lock washers and nuts. NOTE: Do not

tighten any of this hardware until sub-boom assembly is complete (see photos at end of

manual).

P a g e | 3

DSE2455LYK Rev 4/21

6) Install the cable assembly through the hole in the driven element mounting bolt. Make

sure the connector bracket is correctly oriented, the bend should be forward for center mount

antennas and rear facing for rear mount antennas. Solder the outer shield to the driven loop

first making sure there is no shield sticking above the large hole in the driven loop. After the

shield is soldered, pass the center conductor through the small hole in the driven loop and

bend the center conductor over and solder (See Assembly Tips below).

We have created a You Tube video, the link of which can be found on our website,

documenting the following steps:

https://youtu.be/ojXbsDv5cvU

At this point the connector assembly is facing down, connect a piece of coax and your

SWR bridge or VNA. Pull down on the connector (which will flatten the loop) until you reach

the lowest SWR. If it’s less than 1.5:1 you can stop and make sure the loop doesn’t try to pop

back up, sometimes you have to squeeze the loop with your fingers to make sure it stays in

the shape that gave the best SWR. If you want to further lower the SWR, from the rear of the

antenna, place both your thumbs on the driven loop on either side and gently push it forward

towards D1, you only need to tilt it maybe 3/16” to ¼” and that should drop the SWR to 1.1:1

or less.

Now, GENTLY bend the UT-141 coax after it exits the boom towards the front or rear,

depending on the mounting. You do not want to bend it so tightly that it crushes where it

extends through the bolt. The connector bracket should line up with either D1 or D2 (or the

hole with the circle around it on rear mount antennas), remove that nut and place the

connector bracket on the screw and re-attach the nut. If the bracket doesn’t line up,

sometimes you have to flip the bracket. Loosen the ¾” nut by holding the connector body with

a 9/16” open end wrench. Remove the connector bracket and flip it.

Connector doesn’t fit Front Mount Connector Rear Mount Connector

7) Attach the feedline and tape it to the mast. Seal all connections with silicone RTV or

equivalent.

8) Attach the two black end caps, and this will complete the assembly of your

DSE2455LYK.

P a g e | 4

DSE2455LYK Rev 4/21

9) The SWR should be 1.5:1 or better. Additional tweaking can be accomplished by

adjusting the distance between the driven element and R1 or by adjusting the shape of the

driven element.

DO NOT, UNDER ANY CIRCUMSTANCES, APPLY ANY TYPE OF SEALANT OR COATING TO THE

DRIVEN ELEMENT, T-ARMS OR CONNECTOR ASSEMBLY, OTHER THAN KRYLON®

CLEAR COAT. ANY OTHER COATING WILL ADVERSELY AFFECT THE SWR AND VOID YOUR

WARRANTY.

ASSEMBLY TIPS:

The boom diameter is 1 inch, and it is drilled for 4-40 hardware (no. 33 drill bit). The driven

element hole is 5/16-inch dia. All elements are 0.032-inch-thick and 0.375 inch wide except R1

& D1 thru 4 which are 0.250" wide. Note that the element spacing from D7 on is 3.560 inches.

The driven element is installed in the 5/16" hole in the boom. The feed coaxial cable (0.141-

inch semi rigid) goes through the mounting bolt and is formed in a 90-degree bend so that the

connector bracket can be bolted to the boom at Director #1 using the D1 hardware. The

connector end is soldered to the open ends of the brass element. Allow a 1/4" gap at the feed

point. For best match, the driven element should be approximately 2.75 inches high; this

makes it wider than it is tall. This shape can be adjusted for best match. This antenna is based

on work done by G3JVL.

Soldered Driven Element

P a g e | 5

DSE2455LYK Rev 4/21

Boom to Mast Bracket

Boom to Mast Plate

Sub Boom

Sub Boom Plate

Sub Boom

Bracket

P a g e | 6

DSE2455LYK Rev 4/21

ELEMENT TABLE

Note: All dimensions are in inches

P a g e | 7

DSE2455LYK Rev 4/21

Directive Systems Warranty Policy

All Directive Systems antennas are built with the finest materials available. We take great pride

in building a quality product that will give years of good service and performance. If there is a defect

in materials or workmanship within 90 days of purchase, Directive Systems will repair or replace

the defective part, free of charge, to the original purchaser. DO NOT RETURN ANYTHING

WITHOUT PRIOR AUTHORIZATION FROM DIRECTIVE SYSTEMS. Please contact us either by

phone or email describing the problem and we will work to resolve it.

If, after examining a new antenna you received, you are not satisfied, contact us immediately

for return authorization and refund. ANY ANTENNA THAT HAS BEEN MODIFIED WILL BE

SUBJECT TO A RESTOCKING CHARGE. IF AN ANTENNA IS SO MODIFIED AS TO MAKE IT

UNUSABLE, DIRECTIVE SYSTEMS RESERVES THE RIGHT TO REFUSE TO ACCEPT THE

ANTENNA FOR RETURN.

Tabla de contenidos

Otros manuales de Antena de Directive Systems & Engineering

Directive Systems & Engineering

Directive Systems & Engineering DSE3318LYRMK Manual de usuario

Directive Systems & Engineering

Directive Systems & Engineering DSE1345LYK Manual de usuario

Directive Systems & Engineering

Directive Systems & Engineering DSE1445LY Manual de usuario

Directive Systems & Engineering

Directive Systems & Engineering DSE3333LY Manual de usuario

Directive Systems & Engineering

Directive Systems & Engineering DSE1276LY Manual de usuario

Directive Systems & Engineering

Directive Systems & Engineering DSE1345LY Manual de usuario

Directive Systems & Engineering

Directive Systems & Engineering DSE1245LYK Manual de usuario

Directive Systems & Engineering

Directive Systems & Engineering DSE3311LYRMK Manual de usuario

Directive Systems & Engineering

Directive Systems & Engineering DSEFO144-12 Manual de usuario

Directive Systems & Engineering

Directive Systems & Engineering DSE2424LYRMK Manual de usuario

Directive Systems & Engineering

Directive Systems & Engineering DSE3318LYDRM Manual de usuario

Directive Systems & Engineering

Directive Systems & Engineering DSE3333LYA Manual de usuario

Directive Systems & Engineering

Directive Systems & Engineering DSE2345LY Manual de usuario

Directive Systems & Engineering

Directive Systems & Engineering Yagi DSE3319LYCEL Manual de usuario

Directive Systems & Engineering

Directive Systems & Engineering DSE2424LYRM Manual de usuario

Directive Systems & Engineering

Directive Systems & Engineering DSE1245LY Manual de usuario

Directive Systems & Engineering

Directive Systems & Engineering DSE3311LYRM Manual de usuario

Directive Systems & Engineering

Directive Systems & Engineering DS 88-8 Manual de usuario

Directive Systems & Engineering

Directive Systems & Engineering DSE2425LYK Manual de usuario

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Manual de usuario

Directive Systems & Engineering

Directive Systems & Engineering DSE3-50LVA Manual de usuario

Directive Systems & Engineering

Directive Systems & Engineering DSE2345LYK Manual de usuario

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRM Manual de usuario

Directive Systems & Engineering

Directive Systems & Engineering DSE2314LYRM Manual de usuario

Manuales populares de Antena de otras marcas

Alfa Network

Alfa Network APA-L01 Manual de usuario

Naval

Naval PR-422CA Manual de usuario

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Manual de usuario

TERK Technologies

TERK Technologies TV44 Manual de usuario

HP J8999A Manual de usuario

MobilSat

MobilSat MSP-S Manual de usuario

Steren

Steren ANT-UHF 13 Manual de usuario

Novatel

Novatel 600-G Manual de operación

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Manual de usuario

TRENDnet

TRENDnet TEW-AO12O Manual de usuario

Radio Shack

Radio Shack 15-1837 Manual de usuario

CommScope

CommScope CMAX-OMFX-43M-I53 Manual de usuario

Ramsey Electronics

Ramsey Electronics DAP25 Manual de usuario

COBHAM

COBHAM SAILOR 800 VSAT Manual de uso y cuidado

Trango Systems

Trango Systems AD900-9 Manual de usuario

Steren

Steren ANT-100 Manual de usuario

Proxim

Proxim 5054-PA-23 Manual de usuario

IWCS

IWCS iriBelt II Guía de configuración