Dionex ICS-6000 Manual de usuario
ICS-6000 Tablet Installation Instructions
This is an excerpt from the Dionex ICS-6000 Installation manual
Dionex ICS-6000 Installation Instructions
66 Doc. 22181-97001 02/18
3.9 Installing the Tablet
This section contains instructions for attaching the tablet to the DC. The
procedure requires parts from two kits:
•The Tablet Kit (P/N 22181-62020) contains the tablet and its power
supply. When the tablet is purchased from Thermo Fisher Scientific, the
ICS-6000 App is installed on the tablet at the factory and a predefined
user account is created.
•The Tablet Arm/Holder Kit (P/N 22181-62016) contains the parts
required to attach the arm and holder assembly to the DC.
Installation of a Third-Party Tablet
When the tablet is purchased separately from the Dionex ICS-6000, you are
responsible for making sure the tablet meets current specifications (see
Table 3-3).
NOTE If you do not purchase the tablet from Thermo Fisher Scien-
tific, you must also install the ICS-6000 App (see
Section 3.11.1) and manually pair the tablet and instrument
PC (see Section 3.12.2).
Specification Requirement
Table 3-3. Tablet Specifications
3 • System Setup
Doc. 22181-97001 02/18 67
3.9.1 Getting Started
1. Unpack the Tablet Kit (P/N 22181-62020). The kit contains the tablet and
tablet power supply (P/N HAZMAT-01-00136), as well as setup
instructions from the tablet vendor. (You can disregard the vendor
instructions.)
2. Unpack the Tablet Arm/Holder Kit (P/N 22181-62016). The kit contains
all the parts needed to attach the tablet arm to the DC (see Figure 3-26).
3. The mounting arm cover (P/N 22181-60500) is held in place by magnets.
Pull the cover off the mounting arm (see Figure 3-27) and set it aside.
(You will reinstall the cover later.)
Figure 3-26. Tablet Arm/Holder Kit Contents Unpacked
Figure 3-27. Removal of the Mounting Arm Cover
Arm Cover
Cable Guide
Tablet
Holder
Spiral Cable
Wraps
Tablet Tension
Grip
Wiring Duct
3 M4 Screws
Dionex ICS-6000 Installation Instructions
68 Doc. 22181-97001 02/18
3.9.2 Installing the Tablet Arm/Holder
1. Attach the mounting arm (P/N 22181-60500) to the left side of the DC:
a. Note the two lines molded into the base of the tablet mounting arm,
on the inside of the arm (the side of the arm which is installed against
the DC). When installing the mounting arm, make sure the line to the
left of the two fasteners (see Figure 3-28) is in the vertical position.
b. Align the three mounting screws on the base of the mounting arm
with the three mounting holes on the side of the DC (see Figure 3-29).
Figure 3-28. Position Indicator on the Tablet Mounting Arm/Holder
Figure 3-29. Tablet Arm/Holder Mounting Screws on the DC
Vertical Position
Indicator
Fasteners
3 • System Setup
Doc. 22181-97001 02/18 69
c. Use a 3 mm socket driver to tighten the screws from the front of the
mounting arm (see Figure 3-30). You will need to move the arm to
access all three screws.
2. Reattach the mounting arm cover by aligning it with the arm and moving
it toward the arm until the magnets “grab” (see Figure 3-31).
Figure 3-30. Tightening the Tablet Arm Mounting Screws
Figure 3-31. Reattaching the Cover of the Tablet Mounting Arm/Holder
Mounting Screw
Mounting Screw
Note: Mounting screw
behind arm not visible.
Dionex ICS-6000 Installation Instructions
70 Doc. 22181-97001 02/18
3.9.3 Routing the Tablet Power and Ethernet Cables
This section explains how to perform a partial installation of the tablet power
cable and (if required) the Ethernet cable. The connections will be completed
later in the network installation procedure.
1. Connect the tablet power cable (with the round power connector attached)
to the power port on the tablet.
NOTE The tablet is shipped with an AC power cable with a
U.S. NEMA plug. You are responsible for obtaining a
locally sourced plug adapter.
NOTE If a wireless tablet connection will be used, the Ether-
net cable and network adapter are not needed. The
power adapter for the tablet still must reach the tablet
in any chosen tablet arm orientation.
2. Assemble the cable(s) required to connect the tablet USB port to the
network adapter (see Figure 3-32). The parts are provided in the Tablet
Connectivity Kit (P/N 22181-62017).
a. Connect the 2 m (7 ft) Ethernet cable (P/N 00302-99-00129) to the
USB network adapter (P/N 00302-99-00131).
b. If the Ethernet cable is not long enough, connect the USB cable
(male-to-female) (P/N 00302-99-00130) to the adapter.
3 • System Setup
Doc. 22181-97001 02/18 71
NOTE Set the rest of the kit contents aside for use later.
3. Working from the mounting arm backward, route the tablet power and
Ethernet cables from the tablet holder.
4. Check that the power cable can reach the tablet in any desired orientation,
and then secure the power cable with the spiral cable wraps. If the setup
includes an Ethernet cable, it should be routed similarly.
5. Route the network connector (a USB cable that is either attached to the
network adapter or part of the network adapter) as follows (see
Figure 3-33):
a. Route the cable from the top of the tablet holder downward (leaving
about 254 mm (10 in) of cable beyond the top of the tablet holder),
over the arm of the tablet holder, and toward the DC.
b. Secure the cable with the spiral wraps on the upper and lower sections
of the tablet holder arm.
6. Route the tablet power cable as follows (see Figure 3-33):
a. Route the power cable from the top of the tablet holder downward
(leaving about 254 mm (10 in) of cable beyond the top of the tablet
holder), over the arm of the tablet holder, and toward the DC.
Figure 3-32. Tablet Cable Options
3
1
2
4
5
USB-to-Network Adapter
Ethernet Cable
1
2
3
4
5
Ethernet Cable Ethernet Cable
USB-to-Network Adapter
Dionex ICS-6000 Installation Instructions
72 Doc. 22181-97001 02/18
b. Secure the cable with the spiral wraps on the upper and lower sections
of the tablet holder arm.
Figure 3-33. Tablet Power Cable Setup
USB Network
Connector
Power
Cable
Spiral Wrap
Power
Cable
Routing
3 • System Setup
Doc. 22181-97001 02/18 73
7. Route both the Ethernet and tablet power cables through the tablet arm
cable guide (see Figure 3-34) and back toward the tablet holder.
8. Route the cable from the cable guide, down and under the tablet arm, and
toward the rear of the DC.
9. Use the wiring duct (P/N 22181-98020) provided in the Tablet
Arm/Holder Kit (P/N 22181-62016) to organize the cable run across the
side of the DC (see Figure 3-35):
a. Slide the plastic cover off the wiring duct (or flex the duct).
Figure 3-34. Mounting Arm Cable Guide
Arm (inside
view)
Cable Guide Channel
Cable Guide
Channel
Dionex ICS-6000 Installation Instructions
74 Doc. 22181-97001 02/18
b. Remove the paper backing from the adhesive strip and press the base
of the wiring duct firmly onto the side of the DC. Route the cables
through the duct cover and attach it to the base (see Figure 3-35).
3.9.4 Positioning the Tablet
1. Decide whether to locate the tablet in front of the DC or to the left of the
module.
2. Pull the tablet holder release lever (see Figure 3-36) toward yourself and
swivel the holder to move the tablet to the preferred location.
Figure 3-35. Tablet Wiring Duct Attached to the DC
Figure 3-36. Tablet Connection and Viewing Adjustment
Swivel tablet holder to
preferred location
Tablet Holder
Release Lever
Tabla de contenidos
