DIODE LED CHROMAPATH BUNDLE DOME Manual de usuario
1 OF 4 IG060418-1.0
®
INSTALLATION GUIDE
CHROMAPATH®BUNDLE: DOME
CHROMAPATH®BUNDLE: DOME INSTALLATION GUIDE
ALUMINUM CHANNEL
COMPATIBILITY LIST
The following products are compatible with this CHROMAPATH®
Bundle Channel and Cover. Components not listed here are not
compatible.
DRY LOCATION
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
1. Install in accordance with national and local electrical
code regulations.
2. This product is intended to be installed and serviced by
a qualied, licensed electrician.
3. Do not modify or disassemble this product beyond
instructions or the warranty will be void.
4. Do not use if there is any damage to the xture or wiring.
Inspect periodically.
5. Do not install near areas with exposure to salt water or
chlorinated water.
6. Do not install in direct sunlight or damage to the LED
phosphor will occur.
7. Do not attempt to x this product in the eld.
8. Failure to follow safety warnings, and installation
instructions will void the warranty for this product.
SAFETY & WARNINGS
UL Listed
Field
Cuable
AVENUE 24™
BLAZE™
DAZZLE®RGB
DAZZLE®RGBW
DAZZLE®RGBW 4D
TAPE LIGHT
DOUBLE BLAZE™
FLUID VIEW®
ULTRA BLAZE™
VALENT®
VALENT®HD
CLICKTIGHT
CLICKTIGHT PRO
CONNECTORS
CLICKTIGHT 10MM
CLICKTIGHT RGB
2 OF 4 IG060418-1.0
CHROMAPATH®BUNDLE: DOME INSTALLATION GUIDE
CHROMAPATH®BUNDLE: DOME
ALUMINUM CHANNEL
INSTALLATION GUIDE
TOOLS FOR INSTALL INSTALLATION
DETERMINE TAPE LIGHT & CHANNEL
LENGTH
®
+
−
®
+
−
1/4 in.
(6mm)
1/4 in.
(6mm)
Ex. 3 ft. 1 1/2 in. CHROMAPATH Fixture
DETERMINE CHROMAPATH FIXTURE LENGTH
Reector end caps add additional 1/4 in. length to each
side of CHROMAPATH channel.
Total Length = 2x End Caps + CHROMAPATH Channel
1. Pencil
2. Ruler
3. Scissors
4. Band Saw or Rotary Saw
5. Metal File
6. Screwdriver / Electric Drill
®
+
−®
+
−
Ex. 3 ft. Tape Light + Connector
DETERMINE CHROMAPATH CHANNEL CUT LENGTH
The simplest approach is to add 1 in. to CHROMAPATH
Channel and Cover, which will provide space to t end
cap harness. The total channel length is now 3 ft. 1 in.
®
+
−®
+
−
Ex. 3 ft. 1in. CHROMAPATH Channel
TEST CONNECTION
Prior to assembling xture, connect tape light to Class
2 LED driver and turn on power. Ensure connection is
secure and system is working properly. Turn off power
again before mounting. See tape light installation guide
for information on powering xture.
1.3
1.2
DETERMINE TAPE LIGHT LENGTH
Cut to desired length (cut at scissors icon) and attach
appropriate connectors, which will slightly extend total
length. For this example the total length is 3 ft.
1.1
1
1
2
3
4
5
6
3 OF 4 IG060418-1.0
CHROMAPATH®BUNDLE: DOME INSTALLATION GUIDE
CHROMAPATH®BUNDLE: DOME
ALUMINUM CHANNEL
INSTALLATION GUIDE
ASSEMBLE CHROMAPATH FIXTURE
®
+
−
Peel off 3M™adhesive backing from Tape Light.
Press Tape Light gently but rmly against channel, taking
care not to press directly on LEDs.
CUT CHANNEL & COVER
ALUMINUM CHANNELS
Channels can be cut to size with a bandsaw, rotary saw,
or handsaw tted with an appropriate blade to cut metal
objects. Once cut, nish edges with metal le.
CHANNEL COVERS
Covers can be cut to size with heavy duty scissors or a
saw.
INSERT COVER
Run an alcohol wipe along the inside of the channel to
remove any dust or debris.
2
3
INSTALLATION (CONT.)
4
CLEAN CHANNEL AND ADHERE TAPE
LIGHT
4.1
3.3
3.2
3.1
Fasten cover by rmly pressing one edge into channel,
then the other.
4.2 Continue pressing in lens along channel until fully seated.
®
BLAZE
™
E469769
®
+
−
®
BLAZE
™
E469769
®
+
−
4 OF 4
®Toll Free: 877.817.6028 | Fax: 415.592.1596 | www.DiodeLED.com | info@DiodeLED.com
© 2018 Elemental LED, Inc. All rights reserved. Specicaons are subject to change without noce.
IG060418-1.0
CHROMAPATH®BUNDLE: DOME INSTALLATION GUIDE
CHROMAPATH®BUNDLE: DOME
ALUMINUM CHANNEL
INSTALLATION GUIDE
Attach end caps. Adhere with adhesive or glue if desired.
INSTALL MOUNTING HARDWARE ONTO
CEILING
INSTALLATION (CONT.)
Open end cap Closed end cap
5
To bridge between two channels, lay channels
end-to-end, then place cover over gap to keep ends
ush.
4.3
4.5
Place mounting wire within track.
4.4
Fasten hardware to ceiling using included screws.
Thread messenger cables into installed hardware until
tight.
Otros manuales de Equipo de iluminación de DIODE LED
DIODE LED
DIODE LED CHROMAPATH BUNDLE REFLECTOR Manual de usuario
DIODE LED
DIODE LED EMERY BEAM LED Wet Location Batten Fixture Manual de usuario
DIODE LED
DIODE LED VOLANTE LED Canopy Light Manual de usuario
DIODE LED
DIODE LED DI-TB-CONN-TT Series Manual de usuario
DIODE LED
DIODE LED NEON BLAZE RGB 24V LED Strip Light Manual de usuario
DIODE LED
DIODE LED AlphaTECH LED STRIP LIGHT Manual de usuario
DIODE LED
DIODE LED Hydrolume Manual de usuario
Manuales populares de Equipo de iluminación de otras marcas
Qazqa
Qazqa Suplux SL 3 Black 103062 Manual de usuario
Commercial Electric
Commercial Electric 54568141 Manual de usuario
CREE LIGHTING
CREE LIGHTING 304 Series Manual de usuario
Goobay
Goobay 49867 Manual de usuario
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Manual de usuario
Alkalite
Alkalite Krypton KT-81 Manual de usuario
