DINKO Instruments D-25Vplus 1.9747.00 Manual de usuario

VARIABLE FLOW PERISTALTIC PUMPS

Model D-25Vplus

Codes 1.9747.08 and 1.9747.09

MANUAL

July 2023 Marked

c/ Encarnació, 123 -125. Tel. +34 932 846 962. Fax +34 932 104 307

e-mail: dinter@dinko.es www.dinko.es 08024 - Barcelona

INDEX

Page

1- GENERAL INTRODUCTION ······················································································· 3

2- PACKING LIST ········································································································ 3

3- RECEPTION ············································································································ 4

4- DESCRIPTION ········································································································· 5

5- START UP ·············································································································10

6- CHANGING THE TUBES ··························································································14

7- ORDERING INFORMATION ······················································································15

8- MAINTENANCE – SPARE PARTS ·············································································15

9- COMPLEMENTS ·····································································································16

10- CHANGING THE FUSES ··························································································18

11- FLOW TABLE ········································································································18

12- WARRANTY ···········································································································19

13- EC DECLARATION OF CONFORMITY ·······································································20

14- OTHER APPLIANCES ·····························································································21

1- GENERAL INTRODUCTION

Peristaltic pumps pump all kinds of liquid substances without coming into contact with mechanical elements

as in other pumps.

They are easy to use with minimal maintenance.

The pumped substance is impelled into an elastic tube by the vacuum generated by rotors that successively

press and release the surface of the tube.

The liquid passes directly from its container to another without any contamination and without going back

when the pump stops, since the tube remains pressed by the roller.

Some aggressive substances prevent the use of conventional pumps and make peristaltic pumps very

useful for the transfer or dispensing of such substances.

Flow rates are obtained from 0.01ml/minute.

Different size tubes or hoses are available.

The following instructions are intended to ensure correct reception and use of the device, and the safety of

the user.

To this end, we recommend reading this manual in detail before proceeding to unpack the device and

subsequent use.

For proper conservation of the device, it is necessary to avoid its installation in areas with corrosive

atmospheres or exposed to liquid splashes.

Avoid using the appliance when there is the possibility of generating explosive and flammable gas mixtures.

2- PACKING LIST

Description Code Quantity

Peristaltic Pump D-25Vplus 1. 9747.08 or 1.9747.09 1

Silicone peristaltic tube 3mm Ø and connectors 1 x cartridge

Power cord 1

Instruction Manual 1

Warranty 1

Dimensions: 340 x 280 x 180mm. Weight: 7Kg. Stainless steel cabinet.

Operation: 100…240V 50/60Hz

3- RECEPTION

To ensure correct reception, use of the device, and user safety, we recommend reading this manual in

detail before proceeding to unpack the device and subsequent use, and especially the following points:

3.1-THE MANUAL

This manual must be permanently kept within the equipment user's reach.

3.2-UNPACKING

Unpack the appliance, checking that the contents match the packing list.

Immediately notify any eventuality.

3.3-EXPLOSIVE MIXTURES

Avoid using the device when there is the possibility of generating explosive gas mixtures and

flammable. The ATEX Directive is not covered.

3.4-LIABILITY

According to European regulation 89/655/CEE, the lack of adequate maintenance and the alteration of

component, exempts the manufacturer from any responsibility for any damage that may occur.

3.5-REPAIRS

Devices to be sent to DINKO technical services must be clean and disinfected .

Otherwise, they will be rejected and returned with postage paid by the owner.

3.6-SIGNS AND SYMBOLS

Pay attention at all times to the danger warning signs and symbols that will appear in this manual or on

labels attached to the body of the Pump such as those shown below.

SIGN/ SYMBOL

INTERPRETATION

MEANING

Avoid finger contact with moving parts

Danger-Risk-Caution

Before opening

DISCONNECT

the main cable

Before remove cover

PULL OUT plug

Before accessing the interior of the Pump, disconnect the power cable from the main

Possible overheating - Do not touch

110-230V AC 50/60Hz AC power supply voltage

110V AC 60Hz AC power supply voltage

12V DC or 24V DC DC power supply voltage

Disposal of waste electrical and electronic equipment by users within the

European Union.

It is not disposable as household waste.

Deliver to the agency for recycling of electronic equipment.

Contact your local office, the store where you purchased the equipment, or your

household waste disposal service.

Recycling helps conserve natural resources.

Make sure it is recycled protecting human health and the environment.

4- DESCRIPTION

The D-25Vplus peristaltic pumps in this manual mount the 2 or 4-channel MC head that allows the tube

holder cartridge to be easily removed for removal when it must be replaced due to breakage or wear.

Simply press the release lever to release the cartridge from the head.

Each cartridge constitutes 1 dosing channel.

When installing a cartridge, face the cartridge into position, push down, and depress the release lever to

lock the cartridge.

The cartridge admits various tube sizes that, combined with the speed regulation, give a great variety of

flows, as can be seen in the flow chart. .

2 or 4 channel Pumps can be expanded with 2 or 4 cartridge heads up to a maximum of 12 cartridges.

Consult the indicative table of dosages and install the appropriate tube.

4.1 MC HEAD:

2 5

4 channel head

1 – Complementary head assembly screw holes.

2 – Peristaltic tubes.

3 – Tube holder cartridges.

4 – Tube tensioning levers.

5 – Cartridge release lever

The MC head supports another 2 or 4 channel head on its same axis of rotation. Face the complementary

head with the axis and insert the two assembly screws in the holes 1.

When the heads are used as independent channels, each one will provide the flow corresponding to the

tube installed in the heads.

If it is intended to increase the flow, 2 or more suction and discharge pipes can be installed directly in the

feeding and receiving containers.

The option of using a Y connection to join the tubes of two channels will double the pumped flow.

The tube tensioning levers (4) should be tightened just enough for the liquid to begin to flow.

Excessive tension can drastically decrease the life of peristaltic tubing.

4.1.1 How to place and remove the tubes from the head.

The head is delivered with the tubes in place and with the tensioner loosened.

The first thing to do is adjust the tensioner so that the fluid can flow and that it is not too tight to damage

the tube. To do this, with the tensioner loosened, we run the pump, we raise the tensioner little by little

until we see that the liquid begins to circulate.

Initial position. end position

To extract the cartridge where the tube is located, the tensioner must be loosened, that is, in the lowest

possible position. Once loosened, the release lever must be pressed, the cartridges will rise from the right

side and will be free.

Now we can extract the cartridges and thus we can change the tube.

We will remove the tube through the open part of the cartridge.

Once outside we will put the new tube.

To replace the cartridges, we will insert them into the head, first placing the left part in the guide, when we

have it in the guide, we will insert the right part until it is anchored, like this with all the cartridges.

Before starting work, redo the tensioner adjustment as described above.

Initial position. end position

4.2- DESCRIPTION OF THE FRONT PANEL (Photo a).

1 2 3 4 5 6 7

A- Digital reader

1- Counterclockwise rotation key

2- Clockwise direction key

3- Full key

4- Start/Stop key

5- Decrease key

6- Increase key

7- Switch for programming

4.3- DESCRIPTION OF THE REAR PANEL (photo b).

3 4 5 6

1- Main ON/OFF switch

2- Fuse box

3- Power box

4- Voltage-free pedal input

5- 0-10V and 4-20 mA signal input

6- Fan

5 PIN CONNECTOR (0-10V / 4-20 mA) nº5 (Photo b).

0-10V and 4-20 mA CONNECTION

1- Positive (+) pin for 0-10V control

2- Negative (-) pin for 0-10V control

3- Not connect

4- Positive (+) pin for 4-20 mA control

5- Negative (-) pin for 4-20 mA control

WARNING: Do not use simultaneously the two inputs (0-10 V and 4-20 mA).

It may cause malfunction or breakdown.

3-PIN CONNECTOR (voltage-free open contact) No. 4 (Photo b).

ON/OFF CONNECTION (FOOT PEDAL)

1- Pin for connection of voltage-free output (NO). Pump off.

2- Not connected, DO NOT USE.

3- Pin for connection of voltage-free output (NO). Pump off.

If we physically join pins 1 and 3, the pump will start working.

1 3

5- START UP

Make sure that the mains voltage is between 110 and 230 V.

Connect the power cable to the rear plug and to the network.

Consult the indicative flow table and install the appropriate tube.

See tips in the Tube Change and Head Description section.

Select the desired function.

OPERATING MODES.

Available modes:

A- Pumping mode.

B- Ramp mode.

Programming.

Access to the use of the Ramp.

C- Cyclic dosing mode.

Programming.

Access to the use of Cyclic Dosing

D- Pedal dosing mode.

Programming.

Access to the use of Dosage with pedal.

· Pumping mode.

This mode is used to work with the pump continuously, to transfer liquids.

If the pedal is connected, while it is pressed, the head will work, if it is released, the head will stop.

1- Activate rear switch nº1 Pphoto a) O/1.

2- Activate the front switch nº7 (Photo a), it will light up in blue and the display will turn on.

3- Select the motor speed in % by pressing the decrease or increase keys nº5 or nº6(Photo a).

4- If it is necessary to change the direction of rotation, press keys no. 1 or no. 2 (Photo a).

5- Press the No. 4 (Photo a) Start / Stop key to start pumping. To stop pumping, use the same key

no. 4 (Photo a).

If we have the pedal connected, we can start pumping by pressing key no. 4 (Figure a) or by

keeping the pedal pressed. Working with the pedal, the pump will stop when we stop pressing the

pedal.

6- The equipment can be programmed so that if there is a power outage, when it is restored, it

continues to work at the speed that has been programmed. To program this function and at the

speed at which it should resume operation, press key no. 4 (Photo a) for 5 seconds. Its pilot light

will flash and with keys no. 5 or no. 6 (Photo a) we will enter the speed at which we want it to

work if there is a power cut and it is restored, it will be memorized by simply pressing key no. 4

(Photo a) Start / Stop.

To make loading, purging or cleaning tasks easier, press key no. 3 (Photo a) Full. The speed will

progressively increase to the maximum and we will see how it increases on the display up to 99. Pressing

the Full key again will recover the programmed speed, lowering the display to that speed.

Otros manuales para D-25Vplus 1.9747.00

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Bomba de agua de DINKO Instruments

DINKO Instruments

DINKO Instruments D-25VXi Manual de usuario

DINKO Instruments

DINKO Instruments D-25Vplus 1.9747.00 Manual de usuario

DINKO Instruments

DINKO Instruments D-25Vplus 1.9747.00 Manual de usuario

DINKO Instruments

DINKO Instruments D-25VXi Manual de usuario

DINKO Instruments

DINKO Instruments D-25VT Manual de usuario

DINKO Instruments

DINKO Instruments A-60-F Manual de usuario

Manuales populares de Bomba de agua de otras marcas

Neptun

Neptun NPHW 5500 Manual de usuario

Sensidyne

Sensidyne Gilian BDX-II Instrucciones de instalación y funcionamiento

Draper

Draper 47808 Manual de usuario

Trolla

Trolla 12820 Manual de usuario

Sunfab

Sunfab SVH Series Manual de usuario

WilTec

WilTec 50740 Manual de usuario

Fieldmann

Fieldmann FVC 5015 EK Manual de usuario

Everbilt

Everbilt EFSUB5-122HD Manual de usuario

Graco

Graco Husky 3300e Manual de usuario

esotec

esotec 101018 Manual de usuario

moyno

moyno 2000 CC Manual de usuario

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manual de usuario

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guía de solución de problemas

DUROMAX

DUROMAX XP WX Series Manual de usuario

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manual de usuario

Franklin Electric

Franklin Electric IPS Manual de usuario

Xylem

Xylem e-1532 Series Manual de usuario

Milton Roy

Milton Roy PRIMEROYAL Manual de usuario