Dimplex DF2524G Manual de usuario

7213530100R05

Owner’s Manual

Model

DF2524L

DF2524G

6908921359

6908921459

IMPORTANT SAFETY INFORMATION: Always read this manual rst

before attempting to install or use this replace. For your safety, always

comply with all warnings and safety instructions contained in this manual

to prevent personal injury or property damage.

To view the full line of Dimplex products, please visit

www.dimplex.com

2 www.dimplex.com

Table of Contents

Always use a qualied technician

or service agency to repair

this stove.

!NOTE: Procedures and

techniques that are

considered important

enough to emphasize.

CAUTION: Procedures and

techniques which, if not

carefully followed, will result

in damage to the equipment.

WARNING: Procedures

and techniques which, if not

carefully followed, will expose

the user to the risk of re,

serious injury, or death.

Welcome & Congratulations ..................3

IMPORTANT INSTRUCTIONS ................4

Fireplace Installation ........................6

Front Glass Installation .......................6

Mantel Installation ...........................7

Operation .................................8

Maintenance ..............................11

Warranty .................................12

Replacement Parts ..........................14

Welcome & Congratulations

Thank you and congratulations for choosing to purchase an electric

replace from Dimplex, the world leader in electric replaces.

Please carefully read and save these instructions.

CAUTION: Read all instructions and warnings carefully before

starting installation. Failure to follow these instructions may result in a

possible electric shock, re hazard and will void the warranty.

Please record your model and serial numbers below for future

reference: model and serial numbers can be found on the Model and

Serial Number Label.

NO NEED TO RETURN TO THE STORE

Questions with operation or assembly? Require Parts Information?

Product Under Manufacturer’s Warranty?

For Troubleshooting and Technical Support

OR Toll-Free 1-888-346-7539

Monday to Friday 8:00 a.m. to 4:30 p.m. EST

Please have your model number and product serial

number ready. (See above)

S E R IAL No.

MODE L

MOD.

4 www.dimplex.com

When using electrical appliances,

basic precautions should always

be followed to reduce the risk of

fire, electric shock, and injury to

persons, including the following:

① Read all instructions before

using this heater.

② This heater is hot when in use.

To avoid burns, do not let bare

skin touch hot surfaces. The trim

around the heater outlet becomes

hot during heater operation.

WARNING: High tempera-

tures may be generated under

certain abnormal conditions.

Do not partially or fully cover

or obstruct the front of this

heater.

③ Extreme caution is necessary

when any heater is used by or

near children or invalids and

whenever the unit is left operating

and unattended.

④ Always unplug the heater when

not in use.

⑤ Do not operate any heater with

a damaged cord or plug, or if the

heater has malfunctioned, or if it

has been dropped or damaged

in any manner. Return heater

to authorized service facility

for examination, electrical or

mechanical adjustment, or repair.

IMPORTANT INSTRUCTIONS

⑥ Do not use outdoors.

⑦ This heater is not intended for

use in bathrooms, laundry areas

and similar indoor locations.

Never locate this heater where

it may fall into a bathtub or other

water container.

⑧ Do not run cord under

carpeting. Do not cover cord with

throw rugs, runners, or the like.

Arrange cord away from trafc

area and where it will not be

tripped over.

⑨ To disconnect heater, turn

controls to off, then remove plug

from outlet.

⑩Do not insert or allow foreign

objects to enter any ventilation

or exhaust opening as this may

cause an electric shock or re, or

damage the heater.

⑪ To prevent a possible re, do

not block air intakes or exhaust

in any manner. Do not use on

soft surfaces, like a bed, where

openings may become blocked.

⑫ All electrical heaters have

hot and arcing or sparking parts

inside. Do not use in areas where

gasoline, paint, or ammable

liquids are used or stored or

where it will be exposed to

ammable vapors.

SAVE THESE INSTRUCTIONS

⑬ Do not modify the heater.

Use it only as described in

this manual. Any other use

not recommended by the

manufacturer may cause re,

electric shock, or injury to

persons.

⑭ To reduce the risk of electric

shock, this heater has a polarized

plug (one blade is wider than

the other). This plug will t in a

polarized outlet only one way.

If the plug does not t fully in

the outlet, reverse the plug.

If it still does not t, contact a

qualied electrician to install the

proper outlet. Do not change

the plug in any way. Always plug

heaters directly into a wall outlet/

receptacle. Never use with an

extension cord or relocatable

power tap (outlet/power strip).

⑮ Do not burn wood or other

materials in the replace.

⑯ Do not strike the front glass.

⑰Always use a certied

electrician should new circuits or

outlets be required.

⑱ Always use properly grounded,

fused and polarized outlets.

⑲ Disconnect all power supply

before performing any cleaning,

maintenance or relocation of the

heater.

⑳ When transporting or storing

the heater and cord, keep in a

dry place, free from excessive

vibration and store so as to avoid

damage.

WARNING: Remote control

contains a small battery.

Keep away from children. If

swallowed, seek medical attention

immediately.

WARNING: Do not install

battery backwards, charge, put

in re or mix with used or other

battery types - may explode or

leak causing injury.

!NOTE: Changes or

modications not expressly

approved by the party responsible

for compliance could void

user's authority to operate the

equipment.

IMPORTANT INSTRUCTIONS

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

NO USER-SERVICEABLE PARTS INSIDE

6 www.dimplex.com

Fireplace Installation

!NOTE: A 15 Amp, 120 Volt

alternating current (VAC) circuit

is required. A dedicated circuit

is preferred but not essential in

all cases. A dedicated circuit will

be required if, after installation,

the circuit breaker trips or fuse

blows on a regular basis when the

heater is operating. Additional

appliances on the same circuit

may exceed the current rating of

the circuit breaker.

WARNING: Ensure the power

cord is not installed so that it is

pinched or against a sharp edge

and ensure that the power cord is

stored or secured to avoid tripping

or snagging to reduce the risk

of re, electric shock or injury to

persons.

Construction and electrical outlet

wiring must comply with local

building codes and other applica-

ble regulations to reduce the risk

of re, electric shock and injury to

persons. Do not attempt to wire

your own new outlets or circuits.

To reduce the risk of re, electric

shock or injury to persons, always

use a licensed electrician.

Front Glass Installation

1. Unpack the glass assembly.

2. If applicable, carefully pour

and evenly distribute the sup-

plied media in the Media tray

of the rebox (Figure 2).

3. Hang bottom bracket on

screw at the bottom of the

rebox. (Figure 1)

4. Secure the top bracket to re-

box using screws provided in

the hardware bag. (Figure 1)

Figure 1

Figure 2

Media

Tray

Mantel Installation

For use with a new or existing

mantel. Depending on the avail-

able space within the mantel cav-

ity, the unit can be secured to the

mantel at the bottom side or back.

Remove the screw on the bottom

ange in the most appropriate

place for securing and using the

provided L-bracket and the screw

that was removed attach the re-

box to the mantel. (Figure 3)

!NOTE: There are no guide

holes provided for the L-Brackets

in the mantel.

If not installing the unit into a

Dimplex mantel the required

opening dimensions for the

replace are: 24.0 in. (610 mm)

wide x 18 ⅜ in. (467 mm) high x

7 ½ in. (191 mm) deep (Figure 4).

The rebox is to be installed

from the front of the mantel and

inserted so that the anges are

ush against the front surface of

the mantel.

Fireplace Installation

Figure 3

Figure 4

24.0 in.

(610 mm)

18 ⅜ in.

(467 mm)

7 ½ in.

(191 mm)

8 www.dimplex.com

Operation

The unit can be controlled by

either the manual controls which

are located on the upper right of

the replace or the remote (Figure

5 & 6).

The replace is supplied with an

IR multifunction remote control.

!NOTE: To operate correctly,

the remote control must be point-

ed towards the front of the unit.

A. Standby

Turns the unit On and Off.

→ Activated by pressing the

Standby button on the remote or

the unit.

• The unit will turn on with the

same functions that it was set

to when it was turned Off and

the intake temperature will be

indicated on the On Screen

Display.

!NOTE: When any button is

pressed the intake tempera-

ture will be displayed on the On

Screen Display for 5 seconds.

B. Flame Effects

Units with Logsets

Cycles through the different

Lighting Effects: Flames and

Log, Flame only, Log Only,

Flames and Log Off.

→ Activated by pressing the

button on the remote or the unit.

Units with Glass Media

The Flames can be turned off

by pressing the button, then

again to turn back on.

→ Activated by pressing the

button on the remote or the unit.

Figure 6

Figure 5

AB C FA

On Screen Display

Operation

C. Heat ON/OFF

Turns the heater function On

and Off based on the thermostat

setpoint.

→ Activated by pressing the

button on the unit or the remote.

• Indicated by the icon and

the intake temperature being

displayed on the On Screen

Display, for 5 seconds before

turning off.

!NOTE: The unit can be oper-

ated in Heat Only Mode. When

the unit is only running with the

heater, the icon and the intake

temperature will continuously

be displayed on the On Screen

Display.

!NOTE: The heater may emit

a slight, harmless odor when rst

used. This odor is a normal con-

dition caused by initial heating of

internal heater parts and will not

occur again.

D & E. Thermostat Controls

Adjusts the temperature set point

to your individual requirements.

Once the desired set temperature

is reached the heater will turn off.

The heater will cycle on and off

to maintain the desired set tem-

perature. The default temperature

setting is 72°F (22°C).

→ Adjusted by pressing the

to decrease the setpoint and the

to increase the setpoint on the

remote.

• The On Screen Display will in-

dicate the temperature setpoint

as it is adjusted.

!NOTE: Holding the button

down on the unit will change the

temperature from °C to °F, or vice

versa.

Disable Heat

If desired, depending on the sea-

son, the heater on the unit can be

disabled. The unit will operate in

the same fashion, with remainder

of the controls.

Pressing the and buttons

on the unit at the same time and

holding for 2 seconds will disable

and enable the heater.

!NOTE: When the heater has

been disabled and either the

or the is pressed the On

Screen Display will indicate "--".

F. Sleep Timer

The Sleep Timer can be set to

automatically shut off the replace

after a preset time (from 30 min-

10 www.dimplex.com

Remote Control Battery

Replacement

To replace the battery:

1. On the back of the remote

control, turn the battery cover

counter-clockwise to remove

the cover.

2. Correctly install one 3 Volt

(CR2032) battery in the battery

holder.

3. Close the battery cover.

Battery must be recycled

or disposed of properly.

Check with your Local

Authority or Retailer for recycling

advice in your area

Operation

utes to 8 hours).

→ To set the timer press the timer

button on either the remote or the

unit, repeatedly, until the desired

time is displayed.

• The On Screen Display will

display the different times as it

is adjusted. Once the timer has

begun, pressing the button

will display the time remaining

before the unit turns Off.

!NOTE: The Sleep Timer can

be cancelled at any time by

pressing the button repeat-

edly until the sleep timer displays

nothing.

Resetting the Temperature

Cutoff Switch

Should the heater overheat, an

automatic cut out will turn the

heater off and it will not come

back on without being reset. It

can be reset by unplugging the

unit and waiting 5 minutes before

plugging the unit back in.

CAUTION: If you need to con-

tinuously reset the heater, unplug

the unit and call technical support

at 1-888-346-7539.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Chimenea de interior de Dimplex

Dimplex

Dimplex Brayford BFD20E Manual de instrucciones

Dimplex

Dimplex VERDI VER20 Manual de usuario

Dimplex

Dimplex DVF1200 Manual de usuario

Dimplex

Dimplex Toluca Deluxe Manual de usuario

Dimplex

Dimplex DCF7850 Manual de usuario

Dimplex

Dimplex Vivente VVT125 Manual

Dimplex

Dimplex SP620 Manual de usuario

Dimplex

Dimplex DF3033ST Manual de usuario

Dimplex

Dimplex BF33ST Guía de inicio rápido

Dimplex

Dimplex GDS28L8-1941WE Manual de usuario

Dimplex

Dimplex DIMPLEX ELECTRIC FIREPLACE Manual de instrucciones

Dimplex

Dimplex Optiflame 3D Braemar BMR20 Manual de instrucciones

Dimplex

Dimplex Toluca Deluxe Manual de usuario

Dimplex

Dimplex OPTIMYST CAS400L Manual técnico

Dimplex

Dimplex Cassette L Pebble Manual de usuario

Dimplex

Dimplex Juneau JUN Manual de usuario

Dimplex

Dimplex Opti-myst RTOPW20 E Manual de usuario

Dimplex

Dimplex BFSL33 Manual de usuario

Dimplex

Dimplex Obsidian OBS20 Manual de usuario

Dimplex

Dimplex BLF50 Manual de usuario

Dimplex

Dimplex YEO20 Manual de usuario

Dimplex

Dimplex DFOP25 Manual de usuario

Dimplex

Dimplex MULTIFIRE DF3215 Manual de usuario

Dimplex

Dimplex Wickson Manual de usuario

Manuales populares de Chimenea de interior de otras marcas

Brigantia

Brigantia 35-DVRS31N-2 Manual del propietario

Nordpeis

Nordpeis Bergen Manual de usuario

Superior

Superior BCT2536TMN Manual de usuario

Quadra-Fire

Quadra-Fire 5100I-GD-B Manual de usuario

Renaissance

Renaissance RUMFORD 1000 Manual de usuario

Lacunza

Lacunza IV-800 Manual de usuario

Baxi

Baxi 940 Instrucciones de uso

Dru

Dru Maestro 60/2 Tall RCH Manual de usuario

Diamond Fireglass

Diamond Fireglass SS-O22 Manual de usuario

HearthStone

HearthStone Windsor Bay 8830 Manual de programación

Napoleon

Napoleon ASCENT B42 Manual de usuario

Enviro

Enviro E33GI Manual de usuario

Smeg

Smeg L30 FABE Instrucciones de montaje

KEDDY

KEDDY K700 Manual de usuario

Godin

Godin 3451 Manual de usuario

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Manual de usuario

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Manual de usuario

Desa

Desa CCFPDFT Manual de operación