m-Dimension Element Manual de usuario
OWNER'S MANUAL
Acoustic Research
Woofer Installation:
EL COMP 6B
clockwise
EL CO 4B / EL C 4BAX OMP EL COMP 6V
manufactured for
Europe
www.u-dimension.eu
EL COMP B4B / EL COMP 6
Tweeter Installation:
EL COMP 6V
A Division of CHPW
Friedrich-Ebert-Str. 42
D-92637 Weiden / Germany
Introduction
Pre-Installation Instructions
Congratulations on your purchase of µDimension
ELEMENT Automotive Loudspeakers! They have
been built to meet rigorous standards of
construction and performance established
our renowned home
This manual has been designed to make ELEMENT
Loudspeaker installation and ownership as
trouble Please read through this manual
completely installation steps and
familiarize with your new speaker system.
You will need your purchase receipt as proof of purchase
for all warranty repairs and for insurance
purposes. owner's manual, and
packing materials in a safe future
use.
series
the same
that have long
and professional speaker systems.
Automotive
-free as possible.
before attempting any
yourself
any and
Keep your receipt,
location for possible
It is recommended that you have your new ELEMENT
Autom Loudspeakers professionally install
authorized ELEMENT dealer. This will
use techniques and
will If you
you
you ELEMENT
or vehicle.
A. Always make sure the speaker will easily t into the
intended mounting location and that there is adequate
depth to the magnet structure.
series otive ed
by your ensure the
of proper installation materials, and
save much time and effort. choose to perform
own installation, the following instructions will give
series direction toward making your
complete. Read the following information and
precautions carefully. Failure to follow the stated
precautions may result in personal injury and/or
damage the audio system
cavity accept
B. Check for adequate clearance between speaker and
window, window crank, power window mechanism,
seat, glove box, rear deck torsion bars, and other items
which may interfere with the speaker's mounting. This is
especially important if any hole cutting is required.
complete speaker, mounting size and depth requirements
can be found at the end of this manual. A good way to
conrm speaker place meet on a door or body panel is
to place the speaker's die cast mounting ring onto the
surface. Check for a at mounting surface, free from all
obstruction.
purchase
C. The method of installation chosen and level of
execution will effect the overall performance of the
speaker system. Treat each installation step with a high
degree of attention.
D. Do not mount the speaker where water may splash
the woofer cone. A plastic cup or some heavy gauge
plastic sheeting may be needed in some locations that
are exposed to moisture from behind the body panel.
E. Care must be taken to prevent low frequency cancel-
lation caused by air leakage between the front and rear
of the speaker (such as when mounted on a curved or
uneven surface, or when mounted in an oversized hole).
F. Mounting panel reinforcement may be necessary in
some cases in order to prevent surface ex. This can be
achieved by mounting the speaker on a metal or
wooden sub-bafe behind the body or door panel.
Consult an installation specialist for further direction.
G. Unless you are replacing existing speakers of same
size, mounting locations will have to be cut into the
doors, body panels, or rear deck. In some cases speaker
mounting holes will be precut in the doors, body panels,
or rear deck steel. Due to their structural integrity and
accessibility. These precut mounting holes should be
used whenever possible.
IMPORTANT: Never cut any metal that is an integral
part of an automobile's safety or structural support
system.
NOTE. trongly recommends that you operate µDimension s
the complete audio system at low volume before nal
installation of your ELEMENT Automotive Loudspeakers.
This will allow a trial listening test before securing the
loudspeakers into their mounting locations.
CAUTION: Make sure that all speaker wiring is fully
protected from cutting or wear. Any short circuits
developing as a result could severely damage the
rado unit or amplier. Make sure that all speaker
wires easily reach the speaker terminals with stress
on the wire or connectors.
ELEMENT Speaker Installation
EL COMP 6B
High Performance 6-3/4" 2 Way BMW Component System
BMW E46 OEM size stamped basket with voice coil cooling vents.
Strong high grade magnet with pole piece voice coil cooling vent.
6-3/4" ELEMENT P.P. cone with phase plug dustcap at rubber surround.
25mm silk dome Tweeter with neodymium magnet, ush/surface mounts.
BMW OEM Plug & Play crossover with tweeter protection, pre wired.
Optional ELEMENT -3dB tweeter level Plug & Play resistor included.
EL COMP 4B
High Performance 4" 2 Way BMW Component system
BMW 100mm ABS basket, resonance free solid screw terminal.
Strong neodymium magnet with pole piece VC cooling ventilation.
4" ELEMENT P.P. cone with phase plug dustcap at rubber surround.
25mm silk dome Tweeter with neodymium magnet, ush/surface mounts.
BMW OEM plug & play crossover with tweeter protection, pre wired.
Optional ELEMENT -3dB tweeter level plug & play resistor included.
EL COAX 4B
High Performance 4" 2 Way BMW Coaxial Speaker
BMW 100mm ABS basket, resonance free solid screw terminal.
Strong neodymium magnet solid screw terminal connection
4" ELEMENT P.P. cone with rubber surround.
BMW OEM plug & play with 20mm silk dome Tweete neodymium r.
EL COMP 6V
High Performance 6- " 2 Way VW Component system
Euro DIN stamped basket, 6-1/2" ELEMENT P.P. cone with phase plug dustcap.
Strong high grade magnet, protected with ELEMENT rubber cover.
VW Golf 6+7 mount 25mm silk dome Tweeter with neodymium magnet.
VW Golf 6+7 OEM Plug & Play crossover with tweeter protection, pre wired.
VW Golf 6+7 OEM resonance free ABS installation adapters included.
Optional ELEMENT -3dB tweeter level Plug & Play resistors included.
and
1/2
Woofer V.C. Diameter
Tweeter V.C. Diameter
System Impedance
Power Handling (RMS)
Power Handling (Max)
Frequency Response
Sensitivity
25mm
25mm
4ohms
50W
1 0W2
100-22k Hz
88dB (1W/m)
EL COMP 4B
25mm
20mm
4ohms
5 W0
100W
100-20k Hz
88dB (1W/m)
EL COMP 6B EL COMP 6V
General Features
Specification:
25mm
25mm
4ohms
7 W0
150W
60-22k Hz
90dB (1W/m)
EL COAX 4B
Models: EL CO B / EL COMP 4B / EL CO B / EL COMP 6VAX 4 MP 6
25mm
25mm
4ohms
7 W0
150W
60-22k Hz
90dB (1W/m)
Otros manuales de Altavoces para coche de m-Dimension
