digitalview HD-3000 Manual de usuario
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 1.01: 7 July, 2017 Page
1 of 15
HD/SD-SDI to HDMI adaptor board
HD-3000
Manual
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 1.01: 7 July, 2017 Page
2 of 15
Table of Contents
Introduction
3
Connectors, Pin outs &
Ju pers
5
Board Di ensions
10
Signal Support Mode
Table
11
Specification
12
Warranty, Caution &
Li itation of Liability,
Trade arks
13
Contact details
14
Revision History
15
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 1.01: 7 July, 2017 Page
3 of 15
1. Introduction
The HD-3000 converts SD/HD-SDI (SD, HD and 3G) signa to HDMI for driving HDMI monitors. The HD-3000 provides re-c ocked oop
through outputs for “daisy chaining” mu tip e monitors or other equipments to the same HD-SDI source. It a so supports embedded
audio.
Fu y comp iant with the SMPTE 259M-C, SMPTE 292M, SMPTE 424M, 425M standards.
HD-3000 Key Features
a. Supports 1.5Gbits & 3Gbits bit rate input signal support.
The mode support is isted in page 11.
b. Dual channels input port supported.
HD-3000 supports Path A (HD-SDI input from J1 port convert to output HDMI at HDMI1/HDMI1A port) and Path B (HD-SDI input
from J2 port convert to output HDMI at HDMI2/HDMI2A port). See Figure be ow :
c. HD-SDI re-clock loop through output.
J1 HD-SDI input and re-c ock oop through to J3 HD-SDI output. J2 HD-SDI input and re-c ock oop through to J4 HD-SDI output.
d. HDMI (v1.3) x 2 output port.
Two HDMI output ports are HDMI1/HDMI1A, HDMI2/HDMI2A.
e. Stereo e bedded audio support
f. On-board power on/off switch – The power on/off switch is insta ed on SW1.
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 1.01: 7 July, 2017 Page
4 of 15
g. Status LEDs on board :
The definition of the LED1, LED2, LED3, LED4 are :
Ref Description
LED1 / LED2 Green LED on : Signa detected
Green LED B inking : No signa detected
LED3 / LED 4 Green LED on : Signa output
Green LED off : No signa output
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 1.01: 7 July, 2017 Page
5 of 15
2. CONNECTORS, PINOUTS & JUMPERS
The various connectors are:
Su ary: Connectors
Ref Description Type / Use
J1 SD/HD-SDI 1 Input BNC connector
J2 SD/HD-SDI 2 Input BNC connector
J3 SD/HD-SDI 1 re-c ock oop through output BNC connector
J4 SD/HD-SDI 2 re-c ock oop through output BNC connector
CN1 RS-232 & I
2
C contro connector JST 6-way, B6B-XH-A (Matching type : XHP-6)
CN2 Reserved for programming use Reserved
CN3 Reserved for programming use Reserved
CN4 Externa I/O connector Hirose DF13-6P-1.25DSA
(Matching type : Hirose DF13-8S-1.25C)
CN5 Reserved for programming use Reserved
HDMI1 HDMI 1 Output HDMI connector
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 1.01: 7 July, 2017 Page
6 of 15
Ref Description Type / Use
HDMI2 HDMI 2 Output HDMI connector
HDMI1A A ternate HDMI 1 Output JST BM20B-SRDS (Matching type : JST SHDR-20V-S-B)
HDMI2A A ternate HDMI 2 Output JST BM20B-SRDS (Matching type : JST SHDR-20V-S-B)
PP1 Power Input (A ternate) Mo ex 43650-0200 compatib e
(Matching connector type : Mo ex 43645-
0200 compatib e)
(Matching power cab e : P/N 426013800-3)
PP3 Power Input DC power jack, 2.5mm contact pin diameter positive
S1 A ternate power on/off switch connector JST B2B-XH-A (Matching type : XHP-2)
SW1 Power on/off s ide switch S ide switch
SW3 No function Reserved
Su ary: Ju per settings :
Ref Purpose Note
JA1 On board +5V ogic power enab e 1-2 & 3-4 c osed, factory set, do not remove
LED1A Externa LED connection Refer to pin assignment in page 7
LED2A Externa LED connection Refer to pin assignment in page 7
LED3A Externa LED connection Refer to pin assignment in page 7
LED4A Externa LED connection Refer to pin assignment in page 7
JP1-12 No function No function
JP13 Reserved for programming use Reserved
JP14 Reserved for programming use Reserved
SW2 No function No function
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 1.01: 7 July, 2017 Page
7 of 15
Su ary : PinOuts :
CN1 – RS-232 & I
2
C control : JST B6B-XH-A (Matching type : XHP-6)
PIN SYMBOL DESCRIPTION
1 SCLK I2C_SCLK
2 SDATA I2C_SDATA
3 VCC +5V
4 TXD RS-232 Tx data
5 GND Ground
6 RXD RS-232 Rx data
CN4 – External I/O connector : Hirose DF13-6P-1.25DSA (Matching type : Hirose DF13-8S-1.25C)
PIN SYMBOL DESCRIPTION
1 3V3 3.3V output
2 LED3 LED3 Anode
3 LED4 LED4 Anode
4
EXT_IP_0
Reserved
5
EXT_IP_1
Reserved
6 LED1 LED1 Anode
7 LED2 LED2 Anode
8 GND LED Cathode
LED1A, LED2A, LED3A, LED4A – External LED connection
PIN SYMBOL DESCRIPTION
1 + LED Anode
2 - LED Cathode
HDMI1A – Alternate HDMI connector: JST BM20B-SRDS (Matching type : JST SHDR-20V-S-B)
PIN SYMBOL DESCRIPTION
1 GND Ground
2
GND
Ground
3 RXC+ TMDS Data C+
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 1.01: 7 July, 2017 Page
8 of 15
PIN SYMBOL DESCRIPTION
4 RXC- TMDS Data C-
5 RX0+ TMDS Data 0+
6 RX0- TMDS Data 0-
7 RX1+ TMDS Data 1+
8 RX1- TMDS Data 1-
9 RX2+ TMDS Data 2+
10 RX2- TMDS Data 2-
11
GND
Ground
12 GND Ground
13 MSTR2_SCL Reserved
14 MSTR2_SDA Reserved
15 DDC_5V +5V power supp y for DDC (optiona )
16 HPD Hot p ug detection
17 DDC_SCL DDC seria c ock
18 DDC_SDA DDC Data
19 VCC1 VCC 5V output
20 VCC2 VCC 5V output
HDMI2A – Alternate HDMI connector: JST BM20B-SRDS (Matching type : JST SHDR-20V-S-B)
PIN SYMBOL DESCRIPTION
1 GND Ground
2 GND Ground
3 RXC+ TMDS Data C+
4 RXC- TMDS Data C-
5 RX0+ TMDS Data 0+
6 RX0- TMDS Data 0-
7 RX1+ TMDS Data 1+
8 RX1- TMDS Data 1-
9 RX2+ TMDS Data 2+
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 1.01: 7 July, 2017 Page
9 of 15
PIN SYMBOL DESCRIPTION
10 RX2- TMDS Data 2-
11 GND Ground
12 GND Ground
13 MSTR2_SCL Reserved
14 MSTR2_SDA Reserved
15 DDC_5V +5V power supp y for DDC (optiona )
16 HPD Hot p ug detection
17
DDC_SCL
DDC seria c ock
18 DDC_SDA DDC Data
19 VCC1 VCC 5V output
20 VCC2 VCC 5V output
S1 – Alternate power on/off switch connector (Matching type : XHP-2)
PIN SYMBOL DESCRIPTION
1 12V_IN +12V INPUT
2
12V_OUT
+12V OUTPUT
PP1 – Alternate 12VDC power supply
PIN DESCRIPTION
1 +12VDC in
2 Ground
PP3 - 12VDC power supply
PIN DESCRIPTION
1 +12VDC in
2
Ground
Specifications subject to change without notice
© Digital View Ltd – Doc Ver 1.01: 7 July, 2017 Page
10 of 15
3. BOARD DIMENSIONS
Ready- ade 3D Pro-E (SLDPRT) drawing files - Save time and effort for your system vo umetric ana ysis design.
Inc udes jpg fi e previews. P ease go to down oad at http://www.digita view.com/accessories/hd-3000
The maximum thickness of the adaptor board is 18mm (measured from bottom of PCB to top of components, exc uding the
BNC connectors. We recommend c earances of:
• 5mm from bottom of PCB - if mounting on a meta p ate we a so recommend a ayer of suitab e insu ation materia is
added to the mounting p ate surface.
• 10mm above the components
• 3~5mm around the edges
Any of the ho es shown above can be used for mounting the PCB, they are 3.2mm in diameter.
CAUTION: Ensure adequate insulation is provided for all areas of the PCB with special attention to high voltage parts
such as the inverter.
Tabla de contenidos
