Digital Equipment VAX 4000 Model 200 Manual de usuario

VAX 4000 Model 200 (BA430)

Installation

Order Number EK–436AB–IN–002

Digital Equipment Corporation

Maynard, Massachusetts

First Printing, December 1990

Revised, June 1991

The information in this document is subject to change without notice and should not be

construed as a commitment by Digital Equipment Corporation.

Digital Equipment Corporation assumes no responsibility for any errors that may appear in

this document.

The software, if any, described in this document is furnished under a license and may be used

or copied only in accordance with the terms of such license. No responsibility is assumed

for the use or reliability of software or equipment that is not supplied by Digital Equipment

Corporation or its afﬁliated companies.

Restricted Rights: Use, duplication or disclosure by the U.S. Government is subject to

restrictions as set forth in subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer

Software clause at DFARS 252.227–7013.

Printed in U.S.A.

The Reader’s Comments form at the end of this document requests your critical evaluation to

assist in preparing future documentation.

The following are trademarks of Digital Equipment Corporation: CompacTape, CX, DDCMP,

DEC, DECconnect, DECdirect, DECnet, DECscan, DECserver, DECUS, DECwindows,

DELNI, DEMPR, DESQA, DESTA, DSRVB, DSSI, IVAX, KDA, KLESI, KRQ50, MicroVAX,

MSCP, Q-bus, Q22-bus, RA, RQDX, RV20, SA, SDI, ThinWire, TK, TMSCP, TQK, TS05, TU,

VAX, VAX 4000, VAXcluster, VAX DOCUMENT, VAXELN, VAXlab, VAXserver, VMS, VT, and

the DIGITAL logo.

FCC NOTICE: The equipment described in this manual generates, uses, and may emit radio

frequency energy. The equipment has been type tested and found to comply with the limits for

a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed

to provide reasonable protection against such radio frequency interference when operated in

a commercial environment. Operation of this equipment in a residential area may cause

interference, in which case the user at his own expense may be required to take measures to

correct the interference.

S1662

This document was prepared using VAX DOCUMENT, Version 1.2.

Contents

Preface vii

1 Verify Site Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

2 ChecktheShipment................................ 1

3 PositiontheSystem................................ 4

4 OpentheSystemDoors ............................. 5

5 Install the Console Terminal . . . . . . . . . . . . . . . . . . . . . . . . . 7

5.1 Perform Setup Operations . . . . . . . . . . . . . . . . . . . . . . . . . 7

5.2 Connect the Terminal to the System . . . . . . . . . . . . . . . . . 8

6 Set the System Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

7 Connect Additional Devices to the System . . . . . . . . . . . . . . . 15

7.1 Connecting Terminals and Serial Printers . . . . . . . . . . . . . 18

7.2 Connecting Parallel Printers to the System . . . . . . . . . . . . 21

7.3 Connecting Synchronous Modems to the System . . . . . . . . 21

7.4 Connecting Asynchronous Modems to the System . . . . . . . 22

7.5 Connecting an Internal Modem to Telephone Lines . . . . . . 24

7.5.1 DFA01Modems ............................... 24

7.5.2 RJ11C/CA11A, RJ12C/CA12A, and RJ13C/CA13A

TelephoneService.............................. 24

7.5.3 RJ41S/CA41A and RJ45S/CA45A Telephone Service . . . 28

7.5.4 Setting Up Terminal Lines . . . . . . . . . . . . . . . . . . . . . . . 32

7.6 Connecting to an Ethernet Network at the CPU Cover

Panel ......................................... 32

7.6.1 Making a ThinWire Network Connection at the CPU

CoverPanel .................................. 34

7.6.2 Making a Standard Network Connection at the CPU

CoverPanel .................................. 37

7.7 Connecting to an Ethernet Network at the DESQA Module 39

7.7.1 Making a ThinWire Network Connection at the DESQA

Module...................................... 40

7.7.2 Making a Standard Network Connection at the DESQA

Module...................................... 46

iii

8 Connect an Expander, If Required . . . . . . . . . . . . . . . . . . . . . 47

8.1 Connecting the Q-bus Cables . . . . . . . . . . . . . . . . . . . . . . . 50

8.2 Connecting the DSSI Cable . . . . . . . . . . . . . . . . . . . . . . . . 51

8.3 Connecting the KZQSA External Cable . . . . . . . . . . . . . . . 52

8.4 Connecting the Power Control Bus Cable . . . . . . . . . . . . . 55

8.5 Connecting the Ground Cable . . . . . . . . . . . . . . . . . . . . . . 56

9 Connect the KZQSA Internal Cable, If Required . . . . . . . . . . 56

10 Connect the DSSI Cable — Dual Host Only . . . . . . . . . . . . . . 59

11 Connect the Ground Cable — Dual Host Only . . . . . . . . . . . . 62

12 Connect the System Power Cable . . . . . . . . . . . . . . . . . . . . . . 64

13 Turn On the System and Select a Language . . . . . . . . . . . . . 66

14 Close the System Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

15 AfterInstallation.................................. 70

Appendix A Starting and Modifying VMS Factory-Installed

Software

A.1 Pre-Startup Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . A–1

A.2 StartupProcedure ................................. A–2

A.2.1 Modifying FIS for a Standalone System . . . . . . . . . . . . . . . A–3

A.2.2 Modifying FIS for a Simple VAXcluster Network . . . . . . . . A–7

A.2.3 Modifying FIS for a Complex Network or Dual-Host

System........................................ A–11

A.2.3.1 Conﬁguring for Dual-Host Systems . . . . . . . . . . . . . . . . A–12

A.2.3.2 Checking Your Modiﬁcation Work . . . . . . . . . . . . . . . . . A–12

Index

Figures

1 Shipping Carton Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2 Sliding the System into Position . . . . . . . . . . . . . . . . . . . . . . 4

3 Lock and Key Positions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

4 Opening the System Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

5 Connecting a VT300-Series or VT400-Series Console Terminal 9

6 System Controls and Indicators — Power Supply and System

ControlPanel..................................... 11

7 System Controls and Indicators — Integrated Storage

Element and CPU Cover Panel . . . . . . . . . . . . . . . . . . . . . . . 13

8 System Controls and Indicators — TK-Series Tape Drives . . 14

9 System Controls and Indicators — TF85 Tape Drive . . . . . . . 15

10 Connecting Devices to the CXA16 Module . . . . . . . . . . . . . . . 19

11 Connecting Devices to the Cable Concentrator . . . . . . . . . . . . 20

12 Mounting the Cable Concentrator . . . . . . . . . . . . . . . . . . . . . 21

13 Connecting a Modem to a CXY08 Module . . . . . . . . . . . . . . . 23

14 Disconnecting the Telephone Line — Single Line and

MultilineService .................................. 25

15 Installing the Telephone Cord — Single Line and Multiline

Service.......................................... 26

16 Connecting a Modem to a Telephone — Single Line and

MultilineService .................................. 27

17 Connecting a Modem to a Wall-Mounted Jack (Data Jack

Service) — Telephone to Wall-Jack Connection . . . . . . . . . . . 29

18 Connecting a Modem to a Wall-Mounted Jack (Data Jack

Service) — Telephone to DFA01 Connection . . . . . . . . . . . . . . 31

19 Ethernet Connector Switch on the CPU Cover Panel . . . . . . . 33

20 ThinWire Cable, T-Connector, and Terminator . . . . . . . . . . . . 34

21 Making a ThinWire Ethernet Connection at the CPU Cover

Panel ........................................... 35

22 Grounding the ThinWire Ethernet at the CPU Cover Panel . 37

23 Making a Standard Ethernet Connection at the CPU Cover

Panel ........................................... 38

24 DESQA ThinWire/Standard Ethernet Connector Switch . . . . 40

25 ThinWire Cable, T-Connector, and Terminator . . . . . . . . . . . . 41

26 Making a ThinWire Ethernet Connection at the DESQA

Module.......................................... 42

27 Forming the Upper Cable in a Loop at the DESQA Module . . 43

28 Grounding the ThinWire Ethernet at the DESQA Module . . . 45

29 Making a Standard Ethernet Connection at the DESQA

Module.......................................... 46

30 System Connections for Expanders . . . . . . . . . . . . . . . . . . . . 48

31 Connecting the Q-bus Cables . . . . . . . . . . . . . . . . . . . . . . . . . 50

32 Removing the DSSI Terminator . . . . . . . . . . . . . . . . . . . . . . . 51

33 Connecting the DSSI Cable . . . . . . . . . . . . . . . . . . . . . . . . . . 52

34 Removing the KZQSA Terminator . . . . . . . . . . . . . . . . . . . . . 53

35 Connecting the KZQSA External Cable . . . . . . . . . . . . . . . . . 54

36 Connecting the Power Control Bus Cable . . . . . . . . . . . . . . . 55

37 Connecting the Ground Cable . . . . . . . . . . . . . . . . . . . . . . . . 56

38 TLZ04/KZQSA System Connection . . . . . . . . . . . . . . . . . . . . . 57

39 TLZ04/KZQSA Module Connection — Removing the

Terminator....................................... 58

40 TLZ04/KZQSA Module Connection — Connecting the Cable . 59

41 Removing the DSSI Terminators . . . . . . . . . . . . . . . . . . . . . . 60

42 Connecting the DSSI Cable . . . . . . . . . . . . . . . . . . . . . . . . . . 61

43 Connecting the Ground Cable . . . . . . . . . . . . . . . . . . . . . . . . 63

44 PowerSwitch..................................... 64

45 PowerCables..................................... 65

46 Attaching the Power Cable to the System . . . . . . . . . . . . . . . 66

47 Language Selection Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

48 Successful System Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

49 Saving the Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

50 ClosingtheDoors.................................. 70

Tables

1 Module Identiﬁcation Labels . . . . . . . . . . . . . . . . . . . . . . . . . 16

Preface

This manual tells you how to install your system, using the following steps.

1. Verify site preparation

2. Check the shipment

3. Position the system

4. Open the system doors

5. Install the console terminal

6. Set the system controls

7. Connect additional devices to the system

8. Connect an expander, if required

9. Connect the KZQSA internal cable, if required

10. Connect the DSSI cable — dual host only

11. Connect the system ground cable — dual host only

12. Connect the system power cable

13. Turn on the system and select a language

14. Close the system doors

If you are installing a dual-host system, you must repeat each step for each

host. For more information on dual-host systems, refer to your system

Operation manual and to VAX 4000 Dual-Host Systems.

A glossary in your system Operation manual will help you understand new

words and abbreviations that appear in this manual.

CAUTION: Before installing the system, review your system warranty. The

terms of your agreement with Digital may require that a Digital service

representative install the system. Contact your local Digital representative

if you have any questions.

If you are installing an expander with your system:

1. Use this manual to begin the installation of the system.

vii

2. After you complete step 7, install the expander as described in

the installation document (addendum or manual) shipped with the

expander.

3. Return to this manual (step 8) to complete the installation of the

expander and the system.

NOTE: Some of the devices mentioned in this manual are designed for

timesharing systems and may not be suitable for server systems. If you

have a server system, contact your Digital representative if you have any

questions about whether a device is appropriate for your system.

Conventions

The following conventions are used in this manual.

Convention Meaning

Key A terminal key used in text and examples. For example, Break indicates

that you press the Break key on your terminal keyboard.

XXXX Return Bold, monospaced type and the symbol for the Return key indicate

interactive input that you must supply. For example:

>>> BOOT MUA0 Return

That line tells you to enter the command BOOT MUA0 at the console

terminal.

NOTE Provides general information about the current topic.

CAUTION Provides information to prevent damage to equipment or software.

WARNING Provides information to prevent personal injury.

The following warning symbols appear on the power supply. Please review

their meaning:

Indicates risk of electric shock.

To reduce the risk of injury, do not remove modules, Integrated

Storage Elements (ISEs), or the power supply. No user-

serviceable parts are inside. Refer servicing questions to your

viii

Digital service representative or your qualiﬁed self-maintenance

personnel.

The equipment is not designed for connection to an IT power

system (a power system without a directly grounded neutral

conductor). The equipment should be plugged into a dedicated

(isolated) ground circuit.

The system contains an automatic voltage-selection power

supply. Voltage selection is not required prior to installation.

1 Verify Site Preparation

You may have received a copy of the system Site Preparation manual, which

describes the physical, environmental, and electrical requirements for your

system. A copy of that manual is also included in your Customer Hardware

Information Kit. If you have not done so, read that manual and follow its

instructions for preparing your site.

• The installation instructions that follow assume your site meets all the

requirements listed in the Site Preparation manual.

• These instructions also assume all terminal data lines, telephone lines,

and network lines that you plan to connect to your system are in place

and clearly labeled.

You will need the following tools to install your system. They are not

included in your shipment.

• Scissors

• Flat blade screwdriver

• Phillips (cross point) screwdriver

• Adjustable wrench

If you are installing a dual-host system, you must repeat each step in the

installation procedure for each host.

2 Check the Shipment

Before unpacking your system, ﬁnd the Product Delivery Document. It is

attached to the outside of a carton and is labeled with a blue "i" symbol.

That document lists your order and how it breaks out into the items

shipped.

Your shipment may include several cartons:

• One carton contains the system.

• A smaller carton contains the console terminal, if ordered.

• Another carton contains hardware documentation, software documen-

tation, and software licenses. That carton also contains system software

and diagnostic software if you ordered those items separately.

VAX 4000 Model 200 (BA430) Installation 1

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de De oficina de Digital Equipment

Digital Equipment

Digital Equipment MicroVAX 3100 90 Guía

Digital Equipment

Digital Equipment MicroVAX 3100 Model 85 Manual de servicio

Digital Equipment

Digital Equipment VT100 Manual de usuario

Digital Equipment

Digital Equipment VAX 4000 Model 500A Manual de usuario

Digital Equipment

Digital Equipment VAX 4000 500A Manual de usuario

Digital Equipment

Digital Equipment VAX 6000 Series Manual de usuario

Digital Equipment

Digital Equipment DECstation 5000 Model 200 Manual de usuario

Digital Equipment

Digital Equipment VAX 4000 100 Manual de servicio

Digital Equipment

Digital Equipment DEC 3000 300 AXP Series Instrucciones de uso

Digital Equipment

Digital Equipment VAX 4000 300 Manual

Digital Equipment

Digital Equipment DEC 3000 600 AXP Manual de usuario

Digital Equipment

Digital Equipment 900 AXP Manual del propietario

Digital Equipment

Digital Equipment DIGITAL Ultimate Workstation 533 Manual de usuario

Digital Equipment

Digital Equipment DEC 3000 500X AXP Manual de usuario

Digital Equipment

Digital Equipment VAXstation 4000/60 Instrucciones de funcionamiento e instalación

Digital Equipment

Digital Equipment VAXstation 3100 Series Manual de instalación y operación

Digital Equipment

Digital Equipment VAX 4000 108 Manual de operación

Digital Equipment

Digital Equipment 300 Series AXP Manual de usuario

Digital Equipment

Digital Equipment MicroVAX 3100 85 Guía

Digital Equipment

Digital Equipment DECstation 212LP Manual de usuario

Digital Equipment

Digital Equipment Alpha Manual de operación

Digital Equipment

Digital Equipment DECpc AXP 150 Manual de operación

Digital Equipment

Digital Equipment PDP-11/23-PLUS Guía del usuario

Digital Equipment

Digital Equipment Starion Minitower PC 919 Manual de usuario

Manuales populares de De oficina de otras marcas

HP m9060n - Pavilion - Elite Hoja de especificaciones

Asus

Asus E210 Series Manual de usuario

Dell

Dell Inspiron 600m Manual de usuario

Dell

Dell Inspiron 3662 Manual de usuario

TotalFlow

TotalFlow uFLO Manual de usuario

HP Presario SV7000 - Desktop PC Manual de usuario

HP ProDesk 400 G5 Manual

Logitech

Logitech MK320 Manual de usuario

Dell

Dell XPS 730 H2C Manual de usuario

Sony

Sony Vaio Series Manual de usuario

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Manual de usuario

Alto

Alto MD 250 Manual de usuario

Lenovo

Lenovo ThinkCentre Edge 72 Manual

Lenovo

Lenovo ThinkStation D20 Manual

Arbor Technology

Arbor Technology FPC-7800 Series Manual de usuario

Sony

Sony VAIO VGX-TP1 Series Manual de usuario

Asus

Asus Eee Box B204 Manual de usuario

Dell

Dell Optiplex 9010 All In One Manual de usuario