Digital Equipment VAX 4000 Model 100 Guía de inicio rápido

VAX4000

Model100/100AUpgrade

toModel105A

Order Number: EK–V411A–CG. A01

May 1994

Digital Equipment Corporation

Maynard, Massachusetts

May 1994

Digital Equipment Corporation makes no representations that the use of its products in the

manner described in this publication will not infringe on existing or future patent rights, nor do

the descriptions contained in this publication imply the granting of licenses to make, use, or sell

equipment or software in accordance with the description.

Possession, use, or copying of the software described in this publication is authorized only

pursuant to a valid written license from Digital or an authorized sublicensor.

The postpaid Reader’s Comments forms at the end of this document request your critical

evaluation to assist in preparing future documentation.

The following are trademarks of Digital Equipment Corporation: DEC, Digital, ThinWire, VAX,

VAX DOCUMENT, VMS, and the DIGITAL logo.

All other trademarks and registered trademarks are the property of their respective holders.

S2573

This document was prepared using VAX DOCUMENT Version 2.1.

Contents

Preface ..................................................... vii

1 Overview of the Conversion Process

1.1 InThisChapter...................................... 1–1

1.2 Overview of the Conversion Processes . . . . . . . . . . . . . . . . . . . . . 1–1

2 Upgrading the VAX 4000 Model 100 System

2.1 InThisChapter...................................... 2–1

2.2 ProcedureOverview................................... 2–1

2.3 UnpackingtheKit.................................... 2–2

2.4 Upgrading the VMS Operating System . . . . . . . . . . . . . . . . . . . . 2–3

2.5 Replacing the CPU Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–4

3 Upgrading the VAX 4000 Model 100A System

3.1 InThisChapter...................................... 3–1

3.2 ProcedureOverview................................... 3–1

3.3 UnpackingtheKit.................................... 3–2

3.4 Before Installing the Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–3

3.5 Installing the CPU Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–4

A Mandatory Return Procedure and Forms

A.1 ReturnProcedure..................................... A–1

A.2 ReturnForms........................................ A–2

iii

Figures

2–1 Disconnecting the Power Cord . . . . . . . . . . . . . . . . . . . . . . . . 2–4

2–2 Disconnecting the External Cables/Terminators from the Port

Cover........................................... 2–5

2–3 Removing the Enclosure Cover . . . . . . . . . . . . . . . . . . . . . . . 2–6

2–4 Unscrewing the Drive Shelves . . . . . . . . . . . . . . . . . . . . . . . . 2–7

2–5 Disconnecting the Internal Power Cables . . . . . . . . . . . . . . . . 2–9

2–6 Disconnecting Internal DSSI Connectors . . . . . . . . . . . . . . . . 2–10

2–7 RemovingaSIMM................................. 2–11

2–8 Disconnecting the Internal SCSI Cable from the CPU

Module.......................................... 2–12

2–9 Sliding the Drive Mounting Shelves Forward . . . . . . . . . . . . 2–13

2–10 Lifting the Drive Mounting Shelves Upward . . . . . . . . . . . . . 2–14

2–11 Removing the DSSI Daughter Card . . . . . . . . . . . . . . . . . . . . 2–15

2–12 Disconnecting the Q–bus and external SCSI Cables . . . . . . . 2–16

2–13 Removing the Port Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–17

2–14 Removing Connectors from the Port Cover . . . . . . . . . . . . . . 2–18

2–15 Installing the Alignment Pins on the Port Cover . . . . . . . . . . 2–19

2–16 Installing the Original DSSI Cable on the Port Cover . . . . . . 2–20

2–17 Installing the Q–bus Cable on the Port Cover . . . . . . . . . . . . 2–21

2–18 Installing the Blank Covers on the Port Cover . . . . . . . . . . . 2–22

2–19 Installing the SCSI Cable on the Port Cover . . . . . . . . . . . . . 2–23

2–20 Installing the Port Cover and Cables . . . . . . . . . . . . . . . . . . . 2–24

2–21 Removing the CPU Module . . . . . . . . . . . . . . . . . . . . . . . . . . 2–26

2–22 Installing the DSSI Daughter Card . . . . . . . . . . . . . . . . . . . . 2–28

2–23 Connecting the External SCSI Cable to the CPU Module . . . 2–29

2–24 Connecting the Single DSSI Cable to the Daughter Card . . . 2–30

2–25 Connecting the Q–bus Cable to the CPU Module . . . . . . . . . . 2–31

2–26 Aligning the Drive Mounting Shelves . . . . . . . . . . . . . . . . . . 2–32

2–27 Reinstalling the Drive Mounting Shelves . . . . . . . . . . . . . . . . 2–33

2–28 Securing the Drive Mounting Shelves . . . . . . . . . . . . . . . . . . 2–34

2–29 InstallingaSIMM ................................. 2–36

2–30 Reconnecting Cables and Terminators . . . . . . . . . . . . . . . . . . 2–37

2–31 Applying the New Medallion . . . . . . . . . . . . . . . . . . . . . . . . . 2–38

3–1 Disconnecting the Power Cord . . . . . . . . . . . . . . . . . . . . . . . . 3–4

3–2 Removing the Enclosure Cover . . . . . . . . . . . . . . . . . . . . . . . 3–5

3–3 Unscrewing the Drive Shelves . . . . . . . . . . . . . . . . . . . . . . . . 3–6

3–4 Disconnecting the Internal Power Cables . . . . . . . . . . . . . . . . 3–8

3–5 Disconnecting Internal DSSI Connectors . . . . . . . . . . . . . . . . 3–9

3–6 RemovingaSIMM................................. 3–10

3–7 Disconnecting the Internal SCSI Cable from the CPU

Module.......................................... 3–11

3–8 Sliding the Drive Mounting Shelves Forward . . . . . . . . . . . . 3–12

3–9 Lifting the Drive Mounting Shelves Upward . . . . . . . . . . . . . 3–13

3–10 Removing the DSSI Daughter Card . . . . . . . . . . . . . . . . . . . . 3–14

3–11 Disconnecting the Q–bus and external SCSI Cables . . . . . . . 3–15

3–12 Removing the CPU Module . . . . . . . . . . . . . . . . . . . . . . . . . . 3–17

3–13 Installing the DSSI Daughter Card . . . . . . . . . . . . . . . . . . . . 3–19

3–14 Connecting the External SCSI Cable to the CPU Module . . . 3–20

3–15 Connecting the Single DSSI Cable to the Daughter Card . . . 3–21

3–16 Connecting the Q–bus Cable to the CPU Module . . . . . . . . . . 3–22

3–17 Aligning the Drive Mounting Shelves . . . . . . . . . . . . . . . . . . 3–23

3–18 Reinstalling the Drive Mounting Shelves . . . . . . . . . . . . . . . . 3–24

3–19 Securing the Drive Mounting Shelves . . . . . . . . . . . . . . . . . . 3–25

3–20 Installing a Memory Module . . . . . . . . . . . . . . . . . . . . . . . . . 3–27

3–21 Applying the New Medallion . . . . . . . . . . . . . . . . . . . . . . . . . 3–28

Tables

2–1 Contents of the 53XR–AA Upgrade Kit . . . . . . . . . . . . . . . . . 2–3

3–1 Contents of the 53XR–AA Upgrade Kit . . . . . . . . . . . . . . . . . 3–3

Preface

This manual describes how to upgrade a VAX 4000 Model 100 or a VAX 4000

Model 100A system to a VAX 4000 Model 105A by replacing the KA52 CPU

module with a KA53 Module.

Intended Audience

This document is intended for Digital Services personnel and licensed

self-maintenance customers.

Customer Responsibilities

Only qualiﬁed maintenance personnel (Digital Services representatives

or qualiﬁed self-maintenance customers) should perform the installation

procedure.

If you are not a qualiﬁed self-maintenance customer, call Digital Services to

schedule a system conversion. It is your responsibility to perform a software

backup before a Digital Services representative arrives at your site.

When the conversion is complete, return the original CPU module to Digital.

Appendix A contains forms that need to be completed by the Digital Services

representative and signed by both you and the Digital Services representative.

Digital Services Responsibilities

Before arriving at the site, contact the customer to ensure that the customer’s

software is backed up before arriving at the site.

After installation of the upgrade kit, the you must complete the forms in

Appendix A and remove them from this document. The forms must be signed

by both you and the customer.

vii

The following forms are in Appendix A:

• Digital Services Worksheet

• Installation Receipt–Customer Copy

• Installation Receipt–Digital Services Copy

• Returned Material Checklist

You should give the customer the signed Installation Receipt–Customer Copy.

Include the signed Installation Receipt–Digital Services Copy with the CPU

module that is being returned to Digital to ensure that the customer receives

credit.

Organization

This document contains three chapters and one appendix:

• Chapter 1 contains an overview of the upgrade process.

• Chapter 2 provides detailed upgrade conversion procedures for a VAX 4000

Model 100.

• Chapter 3 provides detailed upgrade conversion procedures for a VAX 4000

Model 100A.

• Appendix A contains forms for the return of the original CPU module.

Conventions

The following conventions are used in this guide:

Convention Description

xA lowercase italic xindicates the generic use of a letter. For

example, xxx indicates any combination of three alphabetic

characters.

italic type Italic type emphasizes important information or indicates

variables. It is also used for the titles of manuals.

Note A note contains information that is of special importance to the

user.

Caution A caution contains information to prevent damage to the

equipment.

viii

Manuales populares de De oficina de otras marcas

HP m9060n - Pavilion - Elite Hoja de especificaciones

Asus

Asus E210 Series Manual de usuario

Dell

Dell Inspiron 600m Manual de usuario

Dell

Dell Inspiron 3662 Manual de usuario

TotalFlow

TotalFlow uFLO Manual de usuario

HP Presario SV7000 - Desktop PC Manual de usuario

HP ProDesk 400 G5 Manual

Logitech

Logitech MK320 Manual de usuario

Dell

Dell XPS 730 H2C Manual de usuario

Sony

Sony Vaio Series Manual de usuario

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Manual de usuario

Alto

Alto MD 250 Manual de usuario

Lenovo

Lenovo ThinkCentre Edge 72 Manual

Lenovo

Lenovo ThinkStation D20 Manual

Arbor Technology

Arbor Technology FPC-7800 Series Manual de usuario

Sony

Sony VAIO VGX-TP1 Series Manual de usuario

Asus

Asus Eee Box B204 Manual de usuario

Dell

Dell Optiplex 9010 All In One Manual de usuario