DIGISYSTEM VM-2000 Manual de usuario

Este manual sirve para los siguientes modelos

1

Otros manuales de Equipo de laboratorio de DIGISYSTEM

DIGISYSTEM

DIGISYSTEM DSB-500 Manual de usuario

DIGISYSTEM

DIGISYSTEM WB-500D Manual de usuario

DIGISYSTEM

DIGISYSTEM DSC-302SMD Manual de usuario

DIGISYSTEM

DIGISYSTEM DSO-D Series Manual de usuario

DIGISYSTEM

DIGISYSTEM DSB-500D Manual de usuario

DIGISYSTEM

DIGISYSTEM PS-600T Manual de usuario

DIGISYSTEM

DIGISYSTEM RM-501 Manual de usuario

DIGISYSTEM

DIGISYSTEM DSD-100 Manual de usuario

DIGISYSTEM

DIGISYSTEM DSC-103SD Manual de usuario

DIGISYSTEM

DIGISYSTEM DSD-100D Manual de usuario

Manuales populares de Equipo de laboratorio de otras marcas

Qiagen

Qiagen DML 3000 Manual de usuario

Queensgate

Queensgate NANOSCAN OP400 Manual de programación

Conviron

Conviron GEN1000-GE Manual de usuario

Parr Instrument

Parr Instrument 4560 Manual de instrucciones

IKA

IKA IC control Manual de usuario

Integra

Integra DOSE IT Manual de usuario

Agilent Technologies

Agilent Technologies 5800 ICP-OES Manual de usuario

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Manual de usuario

NI

NI PXI-5422 Manual

Collomix

Collomix Aqix Manual de usuario

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Manual de usuario

Ocean Insight

Ocean Insight FLAME-NIR+ Manual de usuario

Parker

Parker ALIGN-MG-NA Manual de usuario

BD

BD 644787 Manual de usuario

DENTAURUM

DENTAURUM Compact Megaplus Manual de usuario

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Manual de usuario

VWR

VWR SAS Super IAQ Manual de usuario

illumina

illumina MiSeqDx Manual de usuario

DIGISYSTEM LABORATORY INSTRUMENTS INC. www.digisystemlab.com REV.2-2020

INSTRUCTION MANUAL FOR VORTEX MIXER VM-2000 & VM-2000-C

VM-2000-C VM-2000

Warnings:

* Do not remove the mixer during operation.

* Place the mixer securely away from the edge of bench to avoid the mixer falling off the bench top.

* Do not disassemble the mixer by yourself. In the event of a malfunction, the mixer should be repaired by a

qualified technician. Before repairing, turn off the power.

* Clean up the head once the user finds any liquid on the head, otherwise the head will get damaged easily.

Steps:

1. Place the mixer on a flat and stable bench top. Plug the mixer into a properly grounded outlet which

corresponds with the electrical requirements on the label back on machine.

2. Place the ‘Switch’at ‘TOUCH’position. The unit will run as soon as touch on the ‘Head’. The ‘Power

indicator’lights.

3. Place the ‘Switch’at the ‘AUTO’position, the unit will run automatically.

4. Turn the ‘Speed controller’to the required speed.

Warning: Do not make the motor race rotation to avoid damage. After finishing operation, please place the

switch at ‘TOUCH’or ‘OFF’position.

Maintenance and care:

Keep the machine clean all the time, so no routine maintenance is required. Cleaning can be done with a

damp cloth. Avoid the use of solvents as they may damage the machine housing.

Circuit Diagram

Head

Speed controller

Switch

(AUTO/OFF/TOUCH)

DIGISYSTEM LABORATORY INSTRUMENTS INC. www.digisystemlab.com REV.2-2020

Service Manual

Troubleshooting Guide

Caution: Always disconnect the power cord before troubleshooting.

Trouble

Cause

Remedy

Instrument inoperative

Power cord not connected to outlet.

Plug in the power cord.

Dead power output.

Change to different output.

Defective electronic component.

Contact your distributor for repair.

Head doesn’t rotate

Switch isn’t at ‘AUTO or “TOUCH’ position.

Place the switch at ‘AUTO or “TOUCH’ position.

Eccentric brass rod doesn’t work well.

Contact your distributor for repair.

Switch is broken.

Contact your distributor for repair.

Motor is broken.

Contact your distributor for repair.

PC board is broken.

Contact your distributor for repair.

Speed can’t not be controlled

PC board is broken.

Contact your distributor for repair.

Speed controller is broken.

Contact your distributor for repair.

There is a big noise during

operation

Eccentric brass rod doesn’t work well.

Contact your distributor for repair.

Belt which is to fix the eccentric brass rod

doesn’t work well.

Contact your distributor for repair.

The “TOUCH” function can’t

work

Switch isn’t at “TOUCH’ position.

Place the Switch at ‘TOUCH’position.

The starting button under the motor is broken.

Contact your distributor for repair.