Digistar SCALE LINK SL2 Manual de usuario

D4204-EN Rev B December 19, 2018

SCALE LINK - SL2

Technical Manual

Fort Atkinson, Wisconsin USA

www.digi-star.com

www.topconpositioning.com/agriculture

2 Scale Link 2 Technical Manual D4204-EN

TABLE OF CONTENTS

Reference Documents................................................................................. 3

Applicable Products..................................................................................... 4

Specifications .............................................................................................. 5

Part Number Configuration and Options..................................................... 7

PCB and Wiring Connections...................................................................... 8

PCBA ...................................................................................................... 8

Deutsch Connector ................................................................................. 9

Load Cell Connection.............................................................................. 9

SLC2810 Remote Connection.............................................................. 10

Serial Port/ RS232 Connection............................................................. 11

Input and Output Connections.............................................................. 11

System Configurations.............................................................................. 12

Operation References............................................................................... 16

Using SL2 with SLC2810 Remote........................................................ 16

Using SL2 with Universal Terminal (UT)............................................... 16

Updating software, storing and loading settings................................... 16

Selecting the active scale ..................................................................... 17

Changing Setup & Calibration Numbers............................................... 17

Keys Used on Scale Link ISO Terminal................................................ 18

Scale Link Control Overview................................................................. 19

Dead Weight Calibration from ISOBUS Mask ...................................... 21

Dead Weight Calibration from SLC2810 Indicator................................ 22

General ISOBUS/ CAN settings ........................................................... 23

Entering DAN codes on UT .................................................................. 24

Time and Date ...................................................................................... 24

Basic Serial Settings............................................................................. 24

ERM settings......................................................................................... 25

Remote input IP1 settings..................................................................... 25

Output/ FET OP1 settings..................................................................... 25

Options & Accessories .............................................................................. 26

Problems & Troubleshooting..................................................................... 27

Weighing issues.................................................................................... 27

UT/ ISOBUS System............................................................................. 27

SLC2810 System.................................................................................. 28

TST System .......................................................................................... 28

Other Issues.......................................................................................... 28

Menu 1.0 –general settings (jump list 1).................................................. 29

Menu 1.1 –general settings (jump list 11)................................................ 30

Menu 1.2 –time & date (jump list 12) ....................................................... 31

Menu 1.4 –remote inputs (jump list 14).................................................... 31

Menu 1.9 –diagnostic 1 (jump list 19) ...................................................... 33

Menu 2.0 –Communications, remote, & isobus (jump list 2).................... 33

Menu 2.1 –Scoreboard & operational status mess. (jump list 21) ........... 34

Menu 2.2 –port settings (jump list 22)...................................................... 39

Menu 2.3 –print (jump list 23)................................................................... 40

Menu 2.4 –remote display (jump list 24) .................................................. 41

Menu 2.7 –isobus (jump list 27) ............................................................... 42

Menu 2.8 –wIFI (jump list 28)................................................................... 42

Menu 3.0 –weight (jump list 3) ................................................................. 43

Menu 3.1 –motion (jump list 31)............................................................... 44

Menu 3.2 –analog out (jump list 32)......................................................... 44

Menu 3.3 –ACCELEROMETER (jump list 33)......................................... 45

Menu 4.0 –preset, alarm, & timer (jump list 4)......................................... 47

Menu 4.1 –setpoint (jump list 41)............................................................. 48

Menu 4.2 –preset tolerance (jump list 42)................................................ 49

Menu 4.3 –mixer revolutions (jump list 43) .............................................. 49

Menu 5.0 –port outputs (jump list 5)......................................................... 49

Menu 7.1 –scale specific settings (jump list 71)....................................... 50

Menu 7.1 –scale specific settings (scales a & b - jump list 71)................ 55

Menu 7.2 –scale specific settings (scales c & d - jump list 72)................ 56

Menu 8.0 –sign-on & maintenance messages......................................... 56

D4204-EN Scale Link 2 Technical Manual 3

Menu 8.1 –calibration............................................................................... 57

Menu 8.2 –memory management............................................................ 58

Menu 8.7 –setup number & settings ........................................................ 59

4 Scale Link 2 Technical Manual D4204-EN

REFERENCE DOCUMENTS

D3648 EZII Escape Computer Command Set

D4000 ISOBUS/ CAN Application Notes

D4020 EZIV Direct Access Numbers

D4021 Software Release Information

D4055 10/60 Series Technical Manual

D4195 SLC2810 Operator Manual

D4196 Scale Link SL2 ISO Operator Manual

D4197 Scale Link 2000 Installation Manual

D4206 Software Update Instructions

Technical Service Bulletins –reference details of software updates

Other documents available at www.digi-star.com

APPLICABLE PRODUCTS

Compact enclosure

SL2110, SL2140

Full size enclosure

SL2210, SL2220

Scale Link Control (SLC) Remote

SLC2810 with J903 or M12 port

D4204-EN Scale Link 2 Technical Manual 5

SPECIFICATIONS

Voltage Range: 11V –36V DC (12V & 24V machinery) with reverse polarity protection

*For systems manufactured on or before 31DEC2017

9.0V –36V DC (12V & 24V machinery) with reverse polarity protection

*For systems manufactured on or after 01JAN2018

-Limited to 11-16V with SLC2810 or ISOBUS compliant systems

-Gives Low Battery Warning below 11VDC and stops weight display. Recovers and

resumes weighing once voltage is at or above 11VDC.

Current @ 13.8VDC: <0.2A base scale with 4 load cells, up to 5.0A max with active output & all options.

Internal self-resetting fuses for PCB protection & SLC remote protection.

<0.2A ISOBUS SL2 + 4 load cells, no external options

<0.5A ISOBUS SL2 + 16 load cells, no external options

ERM modules add <0.1A to system

SLC2810 adds <0.1A to system

Load Cell Platforms: 16 Maximum 350 ohm transducers; 1 scale platform x 16 bars, 2 scale platforms x 8

bars each, or 4 scale platforms x 4 bars each

Load Cell Excitation: Regulated 8.0VDC, 500mA max, current sensing and overcurrent protected

Operating Environment: -40C to +65C (-40F to 149F); 0 to 95% RH non-condensing

*SLC2810 remote display limited to -29C to +60C (-20F to 140F)

Enclosure: IP65 per IEC529 methods (dust and low pressure water resistant)

Remote Input: Detects open or closed switch state based on software setting. 0 –3,000Hz ground

pulse detection. *+VIN remote input detection not supported at time of publication.

Output Control/ Alarm: Active high 3.0A continuous with 5.0A surge at system level voltage. Output state

programmable in software.

Serial Port: RS232 Com1 & Com2; 1200 –115K baud; 7/8 bits; E/O/N parity;

scoreboard/ streaming data; Serial Gross Weight; DS ERM compatible

M12 harness or direct wire based on SL2 model

Internal USB port: USB 2.0 A port; FAT32 format; thumb drive size up to 32G

For settings save/ load, software update, and ISOBUS mask update

Scale Link Control: SPI bus on 8 pin M12 supports proprietary SPI remotes SLC2810 & SLC2400

CAN 1 Port: Primary CAN port; ISOBUS and Universal Terminal (UT) compatible

CAN 2 Port: Proprietary CAN port for connection to other devices or sensors

Setup & Calibration: Use UT or SLC2810 to access and change settings

Fuses: Main power requires external line fuse. Internal fuses are self-resetting.

Software Features: Software features are similar to EZIV scales. Refer to D4055 and D4020 for settings

changes, functions, print formats, and feature definitions.

6 Scale Link 2 Technical Manual D4204-EN

D4204-EN Scale Link 2 Technical Manual 7

PART NUMBER CONFIGURATION AND OPTIONS

SL2XXX ABC/123/XYZ

Example 1: 410624 SL2140 ISO 4M12/R/S/ACC

This is a compact enclosure with 4 individual scale platforms. It contains an ISOBUS port with 4 M12 load cell

connections, a SLC remote port, a RS232 serial port, and an empty ACC port for IO.

Example 2: 410613 SL2110 ISO/4TB –NO CABLES

This is a compact enclosure for 1 scale platform, with 4 internal terminal blocks for load cell connections. ISOBUS is

enabled and other functions available, but no cables or connectors installed.

Example 3: 410619 SL2220 ISO 8TB/R/S

This is a full size enclosure with 2 individual scale platforms, setup for ISOBUS, SLC remote connections, and serial

port. It has 2 rows of 4 load cell terminal block connections on an additional terminal block PCB for 8 bars total.

Scale Link 2

Box Size

1 = small

2 = large

Number of Scale Platforms

10 = Single Platform A

20 = Dual Platform A-B

40 = Quad Platform A-B-C-D

Option Descriptions

2M12 = Two M12 Load Cell Ports

4M12 = Four M12 Load Cell Ports

4TB = Four Load Cell Connectors

8TB = Eight Load Cell Connectors

2WP = Two Pin Weather Pack

6WP = Six Pin Weather Pack

DB9 = RS232 Cable for PC

F = Wire Ferrules Installed

ISO = ISOBUS Enabled

NO CABLES = No Cables Installed

R = SLC Remote Port

S = RS232 Com1/2 Serial Port

TST = Setup for TST7600

BR = Mounting Bracket Installed

ACC = Extra port for accessories

Option 1

Option 2

Option 3

8 Scale Link 2 Technical Manual D4204-EN

PCB AND WIRING CONNECTIONS

PCBA

RS232 COM1 & COM2, COM

Ground (current limited)

Load Cell connections

USB port

CAN2 port,

CAN2 Ground

(current limited)

Reset button

SLC/ Remote Port

(SPI bus - proprietary)

Power, CAN1/ ISOBUS,

CAN Ground (current limited)

ACC Power, Sensor Input, 3A Output

Single scale models: All 4 terminal

connections are SCALE A

Multi-scale models: Each terminal is

a different scale; A, B, C, D

D4204-EN Scale Link 2 Technical Manual 9

Deutsch Connector

Load Cell Connection

+8V Excitation

6 pin Deutsch Receptacle –Power + CAN1/ ISOBUS

1. +VIN System Input Voltage (Red)

2. CAN1 High (Yellow)

3. 0V System Ground (Black)

4. CAN1 Low (Green)

5. Plug

6. Plug

CAN connection is non-terminated. CANBUS

application requires external 120 ohm termination.

ISOBUS application requires external active bus

termination per ISOBUS standards.

0V Excitation

- Signal

Shield/ Ground

Gray

Black

Blue

White

Brown

Load Cell Connections –On Board and M12 EZ Mates

+ Signal

10 Scale Link 2 Technical Manual D4204-EN

SLC2810 Remote Connection

Header Pinout:

8-7-6-5-4-3-2-1

SLC Remote Port –Proprietary SPI Bus

*Note: +V is fused at 750mA on this port

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Accesorios de Digistar

Digistar

Digistar EZ3400VL Manual de usuario

Digistar

Digistar EZ3400 Manual de usuario

Digistar

Digistar EZ400 Manual de usuario

Digistar

Digistar EZ3600 Manual de usuario

Digistar

Digistar TMR3610 Manual de usuario

Digistar

Digistar EZ400 Manual de usuario

Digistar

Digistar EZ3600 Manual de usuario

Digistar

Digistar GT560 AUTOLOG Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario