DigiPower IPP-S Series Manual de usuario

Digipower Inc.

2017

Digipower Inc.

2017/5/5

Intelligent Power Panel with Switch

Installation Guide

IPP-S Installation guide Digipower Inc.

Table of Content

Installation Diagram.....................................................................................................................1

Faceplate Functional Description.........................................................................................1

1P3W installation Diagram ..................................................................................................2

3P3W installation Diagram ..................................................................................................3

3P4W installation Diagram ..................................................................................................4

Digital Input Wiring Diagram ...............................................................................................5

Digital Output Wiring Diagram.............................................................................................5

Installation Notes.................................................................................................................5

Operation .....................................................................................................................................6

Normal Mode.......................................................................................................................6

Brightness adjusting.............................................................................................................6

Show IP address ...................................................................................................................7

1P3W/3P3W/3P4W setting .................................................................................................7

Test Mode setting.................................................................................................................7

Load setting..........................................................................................................................8

Meter ID setting ...................................................................................................................8

Meter Series Number setting...............................................................................................9

Technical Specification .................................................................................................................9

Web interface.............................................................................................................................11

Information ........................................................................................................................12

Management......................................................................................................................14

Configuration......................................................................................................................20

Mobile app .................................................................................................................................25

IPP-S Installation guide Digipower Inc.

Installation Diagram

Faceplate Functional Description

IPP-S Installation guide Digipower Inc.

1P3W installation Diagram

Notes:

1. The figure Shows 110V / 220V 1P3W power supply system used in the general household.

2. N stand for Neutral, L1-N and L2-N are 110V, L1-L2 is 220V.

3. C1, C2 detect power source. C3, C4 and C5, C6 and C7, C8 detect 220V. C9~C12 detect 110V.

4. In the measurement of 1P3W power consumption, the N as the reference point, with two wattmeter measurement, measure

the voltage between L1-N with current L1, L2-N with current L2. C1 detects L1 current on L1-N, C2 detects L2 current on L2-N.

The rest C3, C4, or, C5, C6 or C7, C8 can be done in the same manner.

5. The Formula and define of 1P3W synthesized as follows:

VAVG(Average voltage)=(V1+V2)

PFEQ(equivalent PF)=WT/VAT

IEQ(equivalent current)=VAT/VAVG

KWHT(TOTAL KWH)=KWH1+KWH2

WT(TOTAL W)=W1+W2

VAT(TOTAL VA)=VA1+VA2

KVAHT(TOTAL KVAH)=KVAH1+KVAH2

6. C9, C11 detect L1 current on L1-N separately. C10, C12 detect L2 current on L2-N separately.

IPP-S Installation guide Digipower Inc.

3P3W installation Diagram

Notes:

1. L1-L2, L2-L3 and L3-L1 are 220V. The figure shown C1, C2, C3 detect 3P3WΔtype total power source, C4, C5, C6 and C7, C8, C9

detect the other two 3P3W power. C10, C11 and C12 detect the one of three phases separately.

2. In the measurement of 3P3W power consumption, the L2 as the reference point, with two wattmeter measurement, measure

the voltage between L1-L2 with current in L1 and L3-L2 with current in L3 to get 3P3W power consumption.

The figure shown C1 detects L1 current, the voltage is L1-L2.

The figure shown C2 detects L2 current, the voltage is L3-L1.

The figure shown C3 detects L3 current, the voltage is L2-L3.

3. The Formula and define of three-phases four-wires synthesized as follows:

VAVG(Average voltage)=(V1+V3) /2

PFEQ(equivalent PF)=WT/VAT

IEQ(equivalent current)=VAT/VAVG

KWHT(TOTAL KWH)=KWH1+KWH3

WT(TOTAL W)=W1+W3

VAT(TOTAL VA)=VA1+VA3

KVAHT(TOTAL KVAH)=KVAH1+ KVAH3

4. The figure shown C10 detects L1 current, the voltage is L1-L2.

The figure shown C11 detects L2 current, the voltage is L2-L3.

The figure shown C12 detects L3 current, the voltage is L3-L1.

IPP-S Installation guide Digipower Inc.

3P4W installation Diagram

Notes:

1. VL1-N = VL2-N = VL3-N , VL1-L2 = VL2-L3 = VL3-L1 = √3 * VL1-N=380V

2. The figure shows C1, C2 and C3 detect 3P4W Y type power source. C4~C12 detect phase to Neutral.

3. In the measurement of 3P4W power consumption, the N as the reference point, with three wattmeter measurement, measure

the voltage between L1-N with current in L1, L2-N with current in L2 and L3-N with current in L3 to get 3P4W power

consumption.

The figure shown C1 detects L1 current, the voltage is L1-N.

The figure shown C2 detects L2 current, the voltage is L2-N.

The figure shown C3 detects L3 current, the voltage is L3-N.

4. The Formula and define of three-phases four-wires synthesized as follows:

VAVG(Average voltage)=(V1+V2+V3) /3 PFEQ(equivalent PF)=WT/VAT

IEQ(equivalent current)=VAT/VAVG KWHT(TOTAL KWH)=KWH1+KWH2+KWH3

WT(TOTAL W)=W1+W2+W3 KVAHT(TOTAL KVAH)=KVAH1+KVAH2+KVAH3

VAT(TOTAL VA)=VA1+VA2+VA3

5. The figure shown C4, C7, C9, C12 detect L1 current, the voltage is L1-N.

IPP-S Installation guide Digipower Inc.

The figure shown C5, C8, C10 detect L2 current, the voltage is L2-N.

The figure shown C6, C11 detect L3 current, the voltage is L3-N.

Digital Input Wiring Diagram

Power Supply:

12 Vdc 0.8A

Input:

Channel Isolated

Range : Contact open(off) or closed (on)

Termination Connection:

14~28AWG,0.2~15mm2

Digital Output Wiring Diagram

Output:

Range : Contact open(off) or closed (on)

Max. switching current: 16A

Max. switching voltage: 250VAC

Max. switching capacity: 4000VA

Termination Connection:

12 ~30AWG,0.2~4mm2

Installation Notes

1. The maximum voltage measurement is 400V.

2. Check that the voltage and current phases are connected properly.

3. Measuring the diameter of the conductor (the bare wire) with the insulation removed and selecting the suitable size of

detachable CT.

4. Measuring voltage: Make sure the CT’s on phases and wires are correct as installation diagram.

5. Measuring current: The positive output can be obtained when the direction of current carrying conductor is the same as the

direction of arrow marked on the CT.

6. The installation of loads combination refers to Installation Diagram.

7. The hardware setting refers to Installation Diagram.

8. Working power supply: AC 115V/230V on terminal R & T, the pinout as shown in Installation Diagram.

9. The software setting refers to Operation.

10. Communication interface: RJ-45, TCP/IP

IPP-S Installation guide Digipower Inc.

Operation

Normal Mode

Item

Key

Description

1.1

Show Loops and CT combination.

1.2

Display the following items:

(1) kW (2)kWh (3)V (4)I (5)PF

1.3

Pressed 3 seconds simultaneously, enter Meter ID setting Mode.

1.4

Pressed 3 seconds simultaneously, enter Brightness adjusting Mode, show version

number and IP address.

1.5

Pressed 3 seconds simultaneously, enter 1P3W/3P3W/3P4W setting Mode.

1.6

Pressed 3 seconds simultaneously, enter Test Mode.

1.7

Pressed 3 seconds simultaneously, enter Load setting Mode.

1.8

Pressed 3 seconds simultaneously, enter Meter Series Number setting Mode.

Brightness adjusting

In this mode, adjust LED brightness from 1 to 9.

Item

Key

Description

2.1

Increase

2.2

Decrease

2.3

One click enters Show IP address mode.

Pressed 3 seconds return to Normal Mode.

2.4

Pressed 3 seconds to save then return to Normal Mode.

IPP-S Installation guide Digipower Inc.

Show IP address

In Brightness adjusting mode, pressed enter Show IP address mode.

Item

Key

Description

2.1

Previous segment display

2.2

Next segment display

2.3

One click enters Brightness adjusting mode.

Pressed 3 seconds return to Normal Mode.

2.4

Pressed 3 seconds to save then return to Normal Mode.

1P3W/3P3W/3P4W setting

In this mode, select 1P3W/3P3W/3P4W in accordance with wires installation.

Item

Key

Description

3.1

Select 1P3W/3P3W/3P4W

3.2

Pressed 3 seconds return to Normal Mode.

3.3

Pressed 3 seconds to save then return to Normal Mode.

Test Mode setting

In this mode, inspect each CT information.

Item

Key

Description

4.1

Select CT number

4.2

Display the following items in sequence:

(1) kW

(2) kWh

(3) V

(4) I

(5) PF

IPP-S Installation guide Digipower Inc.

4.3

Pressed 3 seconds return to Normal Mode.

Load setting

In this mode, set CT combination in each loop.

Item

Key

Description

5.1

Select loop

5.2

Select CT number

5.3

Pressed 3 seconds return to Normal Mode.

5.4

Added/exit loop

5.5

Pressed 3 seconds to save then return to Normal Mode.

Meter ID setting

In this mode, set Meter ID from 1 to 99.

Item

Key

Description

6.1

Select Meter ID

6.2

Select 1st digit or 2nd digit

6.3

Pressed 3 seconds return to Normal Mode.

6.4

Pressed 3 seconds to save then return to Normal Mode.

Note:

1. Set Meter ID = 0, restore factory setting as following:

Meter ID = 01

Load 1 = CT-01

Brightness = 1

3P4W

2. Set Meter ID = 100, restore test setting as following:

Meter ID = 01

Tabla de contenidos

Manuales populares de Panel de control de otras marcas

RDZ

RDZ PC-HRX Manual de usuario

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manual técnico

Efka

Efka Variocontrol V810 Manual de usuario

Cebora

Cebora 208-10 Manual de usuario

AMX

AMX AutoPatch CP-15 Manual de usuario

Satel

Satel CA-6 KLED-S Manual de usuario

Evolution

Evolution IQ plus 800 Manual de usuario

Fagor

Fagor 8040 TCO CNC Manual de usuario

Trane

Trane ComfortLink II XL950 Control Manual de usuario

AKO

AKO PROCool AKO-17635-2 Manual de usuario

ABB

ABB 6136/30M-101 Manual de usuario

Telikou

Telikou BK-603 Belt Pack Manual de usuario

Mapei

Mapei Mapeheat Thermo Touch Manual de usuario

Bosch

Bosch D9412GV4 Manual de usuario

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manual de usuario

Sminn

Sminn BOX L VF1L EI Manual de usuario

Balboa

Balboa TP600 Manual de usuario

Nice

Nice HSCU1 Especificaciones técnicas