Digiplex Paradox ACM12 Guía de configuración

Access Control Module V4.2

ACM12

Installation Instructions

paradox.com

Printed in Canada 05/2014 ACM12-EI02

Introduction

The Access Control Module (ACM12) is designed to be used with the Digiplex EVO

System control panels. Each ACM12 allows you to connect a reader, a REX device, a

door contact and a locking device to control the access to one door. If desired, door

contacts can also be assigned to zones in the control panel to link the doors to the

alarm system. This will allow you to use the same door for the access control

system and the alarm system.

What’s New 4.2

• Support for six additional schedule intervals for Door Unlock Schedule.

• Added security when disarming your system. New option to disarm with

access card and PIN code.

Technical Specifications

Installation

The module is connected to the control panel’s combus as shown in Figure 1.

Please refer to the control panel’s Programming Guide for the maximum

installation distance. Devices connected to the PGM output must be connected as

shown in Figure 2. Refer to Figure 5 for connection drawings for the REX device,

reader, locking device and door contact.

The door contact follows the control panel’s EOL definition. When EOL is

enabled and the door contact is not used, place a 1k



resistor across the CT

and AUX- input terminals. If EOL is disabled, use a jumper. If the REX device is

not used, place a jumper across the REX and AUX- terminals.

AC Power

Use a 16.5Vac (50/60 Hz) transformer with a minimum 20VA. as shown in

Figure 1. Do not use any switch-controlled outlets to power the transformer.

Backup Battery

To power the module’s door lock relay during a power failure, connect a

12Vdc 4Ah rechargeable acid/lead or gell cell backup battery as shown in

Figure 1. Connect the battery after applying AC power.

Inverting the polarity when installing the battery will blow the battery

fuse.

Connecting the External Negative Trigger

The ACM12 comes with an external negative trigger. You can use a PGM from

the control panel or another module to release the access control door lock.

The external negative trigger can also be triggered using a push-button.

When the push button is pressed, the door will unlock. The PGM or push-

button must ground the negative trigger. Connect the push-button as shown

in Figure 2.

LED Display

AC (Green): On when receiving AC power.

BATT (Green): On when charging and during battery tests.

AUX (Yellow): On when auxiliary output is active.

ERROR (Red): Indicates a problem with the module.

RX (Green): Flashes when receiving information from the panel.

TX (Green): Flashes when transmitting information to the panel.

Connection Diagrams

Figure 1: Connecting the power and combus

Figure 2: Additional Connection Information

Figure 3: Connecting a 4-Wire Reader (R910 / R915)

Figure 4: Connecting a 7-Wire Routing Cable

Figure 5: Connecting Access Control Devices

Figure 6: Connecting for Firmware Upgrade (CONV4USB)

AC Power: 16Vac, 20/40VA, 50 - 60Hz

Aux. Power: 12Vdc, typical 600mA, 1A max.

Battery: 12Vdc, 4Ah minimum

No. of Outputs: 2; one 50mA PGM output, one form C relay rated at

5A/28Vdc, N.O./N.C.

No. of Zones: 2 (Door Contact & REX device)

No. of Inputs: 2 (Negative Trigger & Tamper inputs)

Control Panel

Compatibility: Any EVO control panel

Table 1: Special Display

Error RX TX Condition

ON OFF OFF Combus is shorted / No clock / No data

ON OFF ON Wrong data / Invalid Combus address

(Too many modules)

ON ON OFF Future Use

ON ON ON Combus lines reversed (YEL and GRN)

Flash ---- ---- Combus power is too low

12Vdc

Rechargeable Battery:

12V 4Ah min

Disconnect the battery before

replacing the fuse.

Combus

Digiplex/

Digiplex EVO

series control

panel

AUX switch:

Press to toggle the AUX output.

To me ta ll ic e nc lo su re

Ground clamp

Cold water pipe

grounding

AWG #14 single

conductor solid

copper wire

From

transformer

Connect to another

module compatible with

transformer sharing

Transformer Sharing

Transformer Sharing: Use one transformer to power

multiple modules with transformer sharing.

And / Or

To PGM output

External Negative Trigger

External Tamper

Switch (N.C.)

PGM

Connected up to 300m

(1000ft) away.

If the ACM12 loses

communication with the

reader, it will show up as a

Module Fail to Com. trouble.

R915

Reader ACM-12

1: RED to (+)

2: BLK to (-)

3: GRN to (D0)

4: YEL to (D1)

Only connect one reader per ACM12

R910 (not shown) is connected the same way

If you use a routing cable, use a shi elded

routing cable. Do not connect the routing

cable’s shield tothe read er’s shield. Only

connect the routing cable’s shield at the

ACM12.

Connect

Reader ACM-12

1: Red to (+)

2: Black to (-)

3: Green to (D0)

4: White to (D1)

5: Brown to (Beep)

6; Orange to (RED)

7: Yellow to (GREEN)

CR-R880-BL

Only connect one reader per ACM12

CR-R885-BL (not shown) is connected the same way

Connected up to 152m

(500ft) away.

When connecting the diode to the door lock, be sure to

connect the cathode of the diode to the positive (+)

voltage and the anode to the negative (-) voltage.

* = Follows control panel’s EOL definition.

** = If the door contact is not used, install a jumper or a 1k

resistor across the AUX-and CT terminals depending on the

control panel’s EOL definition.

*** = If the Request for Exit (REX) device is not used, place a

jumper across the AUX-and REX terminals.

Cathode

Anode

1N4007

Diode

*** REX device must be

connected to REX terminal

** Door contact

must be

connected to CT

terminal

No EOL required

on REX

CV4USB

ACM12

= Default setting

Only Event Groups 000 to 055, 062 and 063 can be used to program the module’s PGM.

Warranty

For complete warranty information on this product please refer to the Limited Warranty Statement found on the website www.paradox.com/terms. Your use of the Paradox product signifies your acceptance of all warranty terms

and conditions.

We strongly advise that you review and take into consideration the “Limitations of Alarm Systems” document available on our website at http://paradox.com/Terms/.

© 2003-2014 Paradox Security Systems Ltd. All rights reserved. Specifications may change without prior notice. One or more of the following US patents may apply: 7046142, 6215399, 6111256, 6104319, 5920259, 5886632,

5721542, 5287111, 5119069, 5077549 and RE39406 and other pending patents may apply. Canadian and international patents may also apply.

Digiplex EVO is a trademark or registered trademark of Paradox Security Systems Ltd. or its affiliates in Canada, the United States and/or other countries.

Techn ical Supp or t

For technical support in Canada or the U.S., call 1-800-791-1919, Monday to Friday from 8:00 a.m. to 8:00 p.m. EST.

For technical support outside Canada and the U.S., call 00-1-450-491-7444, Monday to Friday from 8:00 a.m. to 8:00 p.m. EST.

Please feel free to visit our website at www.paradox.com.

SECTION [001]: Partition Assignment SECTION [002]: General Options 1

Option OFF ON Option OFF ON

[1] Partition 1 Disabled Enabled [1] Tamper I n p u t Disabled Enabled

[2] Partition 2 Disabled Enabled [2] Battery Charging Current 350mA 850mA

[3] Partition 3 Disabled Enabled [3] Reader’s red LED to follow partition’s status Disabled Enabled

[4] Partition 4 Disabled Enabled [4] Reader’s beeping to follow partition’s status

when option [3] is ON

Disabled Enabled

[5] Partition 5 Disabled Enabled [5] Card activates door unlocked schedule Disabled Enabled

[6] Partition 6 Disabled Enabled [6] Door will relock Imme-

diately

When

closed

[7] Partition 7 Disabled Enabled [7] Reader’s green LED for Access Granted Disabled Enabled

[8] Partition 8 Disabled Enabled [8] Unlock on Request for Exit (REX) Disabled Enabled

SECTION [003]: General Options 2 SECTION [004]: PGM Options

Option OFF ON Option OFF ON

[1] Door Left Open Alarm Disabled Enabled [1] PGM Deactivation After 

Deactiva-

tion Event



PGM Timer

[2] Door Left Open Pre-alarm Disabled Enabled [2] PGM Normal State N.O. N.C.

[3] Door Left Open Alarm Silent Audible [3] PGM Base Time 1 second 1 minute

[4] Door Left Open Alarm follows Alarm

Restore

Beep

Timer

[4] & [5] Special [4] [5]

[5] Door Forced Open Alarm Disabled Enabled Card Only

PIN Only

Card and PIN

Card or PIN

OFF

[6] Door Forced Alarm Silent Audible

[7] Door Forced Alarm follows Alarm

Restore

Beep

Timer

[8] Reader Access Feedback Visual Visual &

audible

[6] Reader Locate Feedback Visual Visual &

audible

[7] Unlock Door on Fire Alarm Disabled Enabled

[8] AC and Battery Supervision Enabled Disabled

Section Data Description Default

[005] __/__/__ (000 to 255 x 1 minute; 000 = Instant) AC failure report delay 030

[006] __/__/__ (001 to 255 seconds) Door Unlocked Period 005

[007] __/__/__ (001 to 255 seconds added to section [006]) Door Unlocked Period extension 015

[008] __/__/__ (001 to 255 seconds) Door Left Open Interval 060

[009] __/__/__ (001 to 255 seconds)

Time to start pre-alarm before alarm is triggered

Door Left Open Pre-Alarm Timer 015

[010] __/__/__ (001 to 255 seconds) Beep timer for Door Left Open Alarm 005

[011] __/__/__ (001 to 255 seconds) Beep timer for Door Forced Open alarm 005

[012] __/__/__ (000 to 255; refer to option [3] in section [004]) PGM timer 005

[013] Door unlock schedule

Start Time End Time S M T W T F S H

Schedule A: ___ ___ : ___ ___ ___ ___ : ___ ___ 1 2 3 4 5 6 7 8

Schedule B: ___ ___ : ___ ___ ___ ___ : ___ ___ 1 2 3 4 5 6 7 8

Schedule C: ___ ___ : ___ ___ ___ ___ : ___ ___ 1 2 3 4 5 6 7 8

Schedule D: ___ ___ : ___ ___ ___ ___ : ___ ___ 1 2 3 4 5 6 7 8

Schedule E: ___ ___ : ___ ___ ___ ___ : ___ ___ 1 2 3 4 5 6 7 8

Schedule F: ___ ___ : ___ ___ ___ ___ : ___ ___ 1 2 3 4 5 6 7 8

Schedule G: ___ ___ : ___ ___ ___ ___ : ___ ___ 1 2 3 4 5 6 7 8

Schedule H: ___ ___ : ___ ___ ___ ___ : ___ ___ 1 2 3 4 5 6 7 8

Event Group Feature Group Start # End #

Section Section Section Section

PGM Activation [014] __/__/__ [015] __/__/__ [016] __/__/__ [017] __/__/__

PGM Deactivation [018] __/__/__ [019] __/__/__ [020] __/__/__ [021] __/__/__

SECTION [022]: Safe Mode Options SECTION [031] PGM Options 2

Option OFF ON Option OFF ON

[1] Safe Mode Disabled Enabled [1] Flexible PGM Deactivation Option PGM Timer

only

 Timer /

Deactivation

event

[2] Safe Mode Access Disabled Enabled [2] Reload Timer on Activation Event Don’t

Reload

Reload

Timer

[3] Reader Safe Mode Feedback Visual  Visual &

audible

[3] to [4] Future Use N/A  N/A

[4] Unlock Door in Safe Mode Disabled Enabled [5] Card and Pin required to disarm* OFF  ON

[5] Access Cards in Safe Mode Safe Cards

only

Any Cards [7] to [8] Future use N/A  N/A

[6] to [8] Future Use N/A  N/A * Only valid when section [004] options 4 and 5 are

enabled.

Section Data Description Default

[023] __/__/__ (001 to 024 hours; 000 = Disabled) Safe Mode Door Unlocked Period 000

[024] __/__/__ (001 to 255 seconds; 000 = Follow REX) REX Unlocked Period 000

[025] __/__/__ (000 to 003) Red LED Brightness 003

[026] __/__/__ (000 to 003) Green LED Brightness 003

[027] __/__/__ (000 to 003) Buzzer Frequency 001

[028] __/__/__ (000 to 255 minutes; 000 = instant) AC Restore Report Delay 005

[029] __/__/__ (000 to 255 minutes) Stay Lock Delay 000

[030] Test PGM: Activates the PGM for 8 seconds to verify if the PGM is functioning properly.

[032] __/__/__ (000 = steady, 001 to 254 = pulsed (increments of 8ms), 255 = pulsed fire) PGM Output type 000

[033] __/__/__ (000 to 255 seconds) Bypass door force alarm delay 000

[040] Access Card Serial Number Display: View an access card’s serial number displayed on any LCD or Grafica keypad on the combus.

When the ACM12 is in access card display mode, the door connected to the module cannot be accessed.

[061] Assign Safe Mode Access Card 1 (Present Card 3 Times)

[062] Assign Safe Mode Access Card 2 (Present Card 3 Times)

[063] Assign Safe Mode Access Card 3 (Present Card 3 Times)

[064] Assign Safe Mode Access Card 4 (Present Card 3 Times)

[070] Delete All Safe Mode Access Cards

[071] Delete Safe Mode Access Card 1

[072] Delete Safe Mode Access Card 2

[073] Delete Safe Mode Access Card 3

[074] Delete Safe Mode Access Card 4

Otros manuales de Controladores de acceso IP de Digiplex

Digiplex

Digiplex DGP-NE96 Instrucciones de funcionamiento

Manuales populares de Controladores de acceso IP de otras marcas

ZKTeco

ZKTeco SpeedFace-V5L Manual de usuario

Jantar

Jantar REX A-1-9 Manual de usuario

2N Access Unit Hoja de instrucciones

Kedacom

Kedacom KSCA120 Series Manual de usuario

H3C

H3C WX2880X Manual de usuario

G4S

G4S S870-EX Guía

PRASTEL

PRASTEL M2000PE Manual de usuario

Allegion

Allegion interflex IF-281 Cylinder Manual de usuario

TECOM

TECOM TS1067E Manual de usuario

Fermax

Fermax Memokey 100C Guía del usuario

Fermax

Fermax CITYLINE MEMOKEY Manual de instrucciones

Software House

Software House iSTAR Pro 2U RM Manual de instrucciones

AKCP

AKCP SP+ Manual de usuario

Bpt

Bpt HNA/102 Manual de usuario

Civintec

Civintec CV9601T-T-1F Manual de usuario

BioMax

BioMax N-X90W Manual de usuario

ZKTeco

ZKTeco OP-200 Manual de usuario

FingerTec

FingerTec s-Kadex Manual de usuario