Digga PDD Manual de usuario
1
OPERATORS MANUAL
AUGER DRIVES PDD - PD50
SINGLE & 2 SPEED
PM-000002-H
2
PM-000002-H PDD-PD50 Operators Manual - November 2017
3
Your Digga Planetary Drive Gearbox is a high performance attachment that is designed for Drilling,
Screw Anchoring (Pier) installation, Core Barreling and other extreme applications where it is seeing
high levels of torque. To avoid premature wear and failure, and to fulll your terms of warranty please
read this statement.
All DIGGA PLANETARY DRIVES must have a rst oil change within the
of use (which ever comes rst) to ensure the bed in of the drive unit.
For more detailed information please read pages 44 - 48
If the rst oil change is not performed within this period excessive wear within the gearbox will occur
that will cause premature failure. All Warranty will be void.
must be
performed by an authorised service agent to ensure Warranty requirements are met.
In the event of a failure under the warranty period:
• Contact Digga immediately, DO-NOT DISASSEMBLE YOUR DRIVE without rst obtaining written
permission and instructions from Digga.
• Proof of service must be provided in hard copy form of both operational and service history (in-
cluding serial number of gearbox and hydraulic motor) records. Service must be performed by an
.
CRITICAL - DO NOT CONNECT OR OPERATE YOUR DRIVE UNIT
WITHOUT FIRST HAVING READ AND UNDERSTOOD THIS STATEMENT
1 CRITICAL INFORMATION - SERVICE INTERVALS
4
PM-000002-H PDD-PD50 Operators Manual - November 2017
2 TABLE OF CONTENTS
CONTENTS PAGE
1 CRITICAL INFORMATION - SERVICE INTERVALS 3
2 TABLE OF CONTENTS 4
3 TO THE PURCHASER - ABOUT THIS MANUAL 5
4 SERVICE & PREPARATION FOR USE 6
5 SAFETY PRECAUTIONS - GENERAL INFORMATION 8
6 SAFETY - WORKING WITH THE ATTACHMENT 14
6 SAFETY - DECAL LOCATION 16
7 BEFORE USE 17
7 BEFORE USE - OPERATING PARAMETERS 18
8 COMMISSIONING PROCEDURE 20
9 OPERATING INSTRUCTIONS 24
10 2 SPEED INSTALLATION INSTRUCTIONS 32
11 2 SPEED OPERATING INSTRUCTIONS 42
12 MAINTENANCE 44
13 AUGERS, WEARPARTS & SPARE PARTS 50
14 TROUBLE SHOOTING 52
15 CONTACT INFORMATION 54
16 WARRANTY 55
5
THANK YOU
Congratulations on the purchase of your new High Performance DIGGA Planetary Drive. This product was carefully designed and
manufactured to give you years of dependable service. It is mandatory that oil changes are performed at the specied interval to
keep it in top working condition (maintenance - chapter 12).
The complete manual must be read and understood before connecting and operating. Be sure to observe all safety precautions and
maintenance procedures as described in this manual.
Optional Extras are available for special applications or extreme conditions: these are noted throughout the manual. Contact your
DIGGA dealer for any further information pertaining to this product or for further information on other products available in the
DIGGA range.
3 TO THE PURCHASER
SAFETY ALERT SYMBOL
This is the “Safety Alert Symbol” used by this industry. This symbol is used to warn
of possible injury. Be sure to read all warnings carefully. They are included for your
safety and for the safety of others working with you.
ABOUT THIS MANUAL
This manual has been designed to help you do a better,
safer job.
.
Remember; never let anyone operate this unit without
reading the “Safety Precautions” and “Operating
Instructions” sections of this manual. Unless noted
otherwise, right and left sides are determined from the
position of the machine operator when facing forward.
6
MODEL______________________________________
SERIAL NUMBER______________________________
DATE PURCHASED____________________________
Your Digga Auger Drive is a
All service and warranty must be performed by an authorised DIGGA service agent. Contact your local Digga
dealer for details.
To facilitate warranty or service, record the model and serial number of your unit in the space provided on this
page. This information may be obtained from the identication plate located on the product.
4 SERVICE & PREPARATION FOR USE
SINGLE & TWO SPEED PREMIUM DRIVES AUGERS TEETH PILOTS
PDD, PDX,
PDZ3, PDX1,
PDX2, PDX3,
PD3, PDT3
PD4, PD4HF
PD5
PD6/PD6HF
PDT6, PDT6HF,
PD7
PD8/PD8HF
PDT8, PDT8HF,
PD10/PD10HF
PDT10HF
PD12, PDT12
PD12-5-VIS
PD14,PD15
PD18, PDT18
PD18-5-VIS
PD22,PDT22,
PD23
PD25,
PDT25,
PD30, PDT30
PD33-7-VIS
PD40,PD50
PDT50
A4, A5
A6, A7
A8, A9
A10, A11
TS-1, TS-2, TS-3
TSC-1, TSC-2, TSC-3
TM-1, TM-2, TM-3
TM-C-1, TM-C-3
TTC-1, TTD-3
TTL-3, TTS-3
PS-1, PS-2,
PS-3
PM-1, PM-2,
PM-3,
PM-SQ-1
PM-HX-3
PH-3
MODELS COVERED IN THIS MANUAL
PM-000002-H PDD-PD50 Operators Manual - November 2017
7
To avoid any inconvenience before operation, please check that you have received the following items which
you have ordered. Items may dier depending on type of machine the Drive units are to be tted to.
4 SERVICE & PREPARATION FOR USE
o
REF DESCRIPTION QTY SINGLE
SPEED
2-SPD
12V/24V
A STD DRIVE UNIT - OR - SCS DRIVE UNIT 1 • •
B QUICK RELEASE COUPLERS set • •
C HYDRAULIC HOSE KIT set • •
D LYNCH PIN (CLIP) OR BOLT 1 • •
E LINKAGE SUIT STD DRIVE UNIT 1 • •
K STD DRIVE UNIT TO LINKAGE PIN 1 • •
L DIGGA MOTOR CONTROL HARNESS (3M) 1 N/A •
M EXTENSION HARNESS 3M/6M/12M/15M 1 N/A OPTIONAL
N 2-SPEED CONTROLLER 1 N/A OPTIONAL
O REMOTE TOGGLE SWITCH 1 N/A OPTIONAL
P REMOTE FLOOR MOUNTED SWITCH 1 N/A OPTIONAL
Q 12V/24V POWER LEAD 1 N/A OPTIONAL
R OPERATORS MANUAL 1 • •
REF FOR EXCAVATORS QTY SINGLE
SPEED
2-SPD
12V/24V
H STD EXCAVATOR HITCH 1 • •
I LINKAGE TO SUIT EXCAVATOR HITCH 1 • •
F-2 SCS CRADLE (IF APPLICABLE) 1 • •
REF FOR SKID STEER LOADERS QTY SINGLE
SPEED
2-SPD
12V/24V
G SLIDE FRAME 1 • •
J CRADLE TO LINKAGE PIN 1 • •
F-1 STD SLIDE CRADLE 1 • •
F-3 SCS CRADLE (IF APPLICABLE) 1 • •
S ADAPTOR HARNESS CAT/ASV/TEREX 1 N/A OPTIONAL
T ADAPTOR HARNESS KIT (14-PIN) 1 N/A OPTIONAL
REF MINI LOADER QTY SINGLE
SPEED
2-SPD
12V/24V
U DRIVE UNIT WITH MINI LOADER MOUNT 1 • N/A
*NOTE • DENOTES SUPPLIED
ALL OTHER MACHINES SINGLE
SPEED
2-SPD
12V/24V
CUSTOM MADE FRAME TO SUIT • •
G
B
F-1
C
E
J
D
H
I
A
OR
K
D
F-2
F-3
L
P
Q
R
M
N
S
T
U
8
PM-000002-H PDD-PD50 Operators Manual - November 2017
SIGNAL WORDS: Note the use of signal words DANGER, WARNING, and CAUTION with the safety messages. The appropriate signal
word for each has been selected using the following guidelines:
DANGER: Indicates an imminently hazardous situation, which if not avoided, will result in death or serious injury. This signal word is to be
limited to the most extreme situations, typically for machine components which, for functional purposes, cannot be guarded.
WARNING: Indicates a potentially hazardous situation, which if not avoided, could result in death or serious injury, and includes hazards
that are exposed when guards are removed. It may also be used to alert against unsafe practices and indicate potential failure or damage
to equipment.
CAUTION: Indicates a potentially hazardous situation, which if not avoided, may result in minor or moderate injury. It may also be used to
alert against unsafe practices.
TAKE NOTE! THIS SAFETY ALERT SYMBOL FOUND THROUGHOUT THIS MANUAL IS USED TO CALL YOUR ATTENTION TO
INSTRUCTIONS INVOLVING YOUR PERSONAL SAFETY OR OTHERS. FAILURE TO FOLLOW THESE INSTRUCTIONS CAN
RESULT IN INJURY OR DEATH.
ATTENTION!
BECOME ALERT!
YOUR SAFETY IS INVOLVED!
THIS SYMBOL MEANS:
This section is composed of various warnings and safety tips.
. Also read your machines owner’s manual before using your equipment. This knowledge will help you operate
your unit safely.
The “Safety Alert Symbol” will be used throughout this manual. It will appear with the word or CAUTION,
and a safety message pertaining to the specic topic being covered. Take the time to read these messages as you come across them.
5 SAFETY PRECAUTIONS - GENERAL INFORMATION
9
KNOW WHERE UTILITIES ARE
Observe overhead electrical and other utility lines. Be sure equipment will clear them. When digging, call DIAL
BEFORE YOU DIG ON 1100 (in Australia), or your local UTILITIES location service provider for location of buried utility
lines, gas, water, and sewer, as well as any other hazard you may encounter.
EXPOSURE TO RESPIRABLE CRYSTALLINE SILICA DUST ALONG WITH OTHER HAZARDOUS DUSTS MAY
CAUSE SERIOUS OR FATAL RESPIRATORY DISEASE.
It is recommended to use dust suppression, dust collection and if necessary personal protective equipment during the
operation of any attachment that may cause high levels of dust.
REMOVE PAINT BEFORE WELDING OR HEATING
Hazardous fumes/dust can be generated when paint is heated by welding, soldering or using a torch. Do all work
outside or in a well ventilated area and dispose of paint and solvent properly. Remove paint before welding or heating.
When sanding or grinding paint, avoid breathing the dust. Wear an approved respirator. If you use solvent or paint
stripper, remove stripper with soap and water before welding. Remove solvent or paint stripper containers and other
ammable material from area. Allow fumes to disperse at least 15 minutes before welding or heating.
END OF LIFE DISPOSAL
At the completion of the useful life of the unit, drain all uids and dismantle by separating the dierent materials (rubber,
steel, plastic, etc.). Follow all federal, state and local regulations for recycling and disposal of the uid and components.
WARNING
WARNING
WARNING
WARNING
5 SAFETY PRECAUTIONS - GENERAL INFORMATION
10
PM-000002-H PDD-PD50 Operators Manual - November 2017
WARNING
WARNING
WARNING
OPERATING THE PLANETARY DRIVE
• An operator must not use drugs or alcohol, which can change his or her alertness or coordination. An operator taking
prescription or over-the-counter drugs should seek medical advice on whether or not he or she can safely operate
equipment.
• All bystanders should be kept a minimum of 6 meters (20 feet) away from the working area of the drive.
• Do not allow Site workers to climb or ride on a drill mast, Planetary Drive, Auger or Auger Extension at any time,
including while stationary, in operation or being moved or rotated.
• Operate only from the operator’s station.
• Avoid steep hillside operation which could cause the machine to overturn. Consult your machines operator’s and safety
manuals for maximum incline allowable.
• Reduce speed when driving over rough terrain, on a slope, or turning, to avoid overturning the vehicle.
• Travel only with the planetary drive in a safe transport position to prevent uncontrolled movement. Drive slowly over
rough ground and on slopes.
• Tether any auger, anchor or extensions connected to the drive with a chain if necessary, to prevent uncontrolled swing-
ing of the attachments when moving from position to position.
• Do not drive close to ditches, excavations, etc., cave in could result.
• Before exiting the machine, lower the attachment to the ground, apply the parking brakes, turn o the prime mover’s
engine, and remove the key.
• Flow and pressure gauges, ttings, and hoses must have a continuous operating pressure rating of at least 25% higher
than highest pressures of the system.
• Do not smoke when refueling the prime mover. Allow room in the fuel tank for expansion. Wipe up any spilled fuel.
Secure cap tightly when done.
• Remove the auger drive from the prime mover before transporting to and from the job site.
• Planetary Drives shall be used only for their designed intent and shall not be loaded beyond their rated capacity. Over-
loading or exceeding the manufacturers specications will void all warranty.
5 SAFETY PRECAUTIONS - GENERAL INFORMATION
Otros manuales para PDD
1
Este manual sirve para los siguientes modelos
65
Tabla de contenidos
Otros manuales de Perforar de Digga
