DiamaPro Systems DP-SCRUB20 Manual de usuario

OWNER’S MANUAL

DP-SCRUB20

AUTO SCRUBBER

USER & MAINTENANCE BOOK

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE

OPERATIONAL SAFETY INSTRUCTIONS

Thank you for purchasing our products. This operation manual will provide you with a comprehensive

guide to operate this machine. Please read this manual carefully before you use the machine and

retain it for future reference.

Please read this manual carefully before using this appliance.

In this manual, there are common safety instructions in detail on appliance preparing, operating and maintenance. The

operator must obey these accident-preventive regulations when using this machine. The manufacturer does not bear any

liability for any accident caused by disobeying these regulations.

This manual is one of the most important pieces of this appliance. Ensure the operator reads or listens to the manufactur-

er’s introduction on this manual. Save this manual where you can easily fetch and read regularly. This manual adopts the

following three kinds of gure as the important indication:

INDICATION:

Key information on economical using.

The possible accident caused by disobeying the manual.

NOTICE:

The possible accident and estate damage caused by disobeying the manual

FORBIDDEN

The possible severe damage to person and estate caused by disobeyed instruction.

SAFETY NOTICE

In case any operation is conducted before reading through the manual, the casualty to the operator or others, and

even the damage to the machine might be unavoidable. No operation will be permitted without prior training and

demonstration

To reduce the risk of re, this machine is only appropriate for cleaning explosion-proof commercial oorings.

Half-installed or half-t machine might cause damage to the operator or others, and might also cause casualty to

the machine or parts of the machine. Before tting it in completely, do not conduct any operation on the machine.

Before operation, one should make sure all components of the machine are well-preserved.

The maintenance of this machine should be performed by trained and qualied technicians. Before maintenance,

unplug the machine from the power outlet for the sake of avoiding more harmful interferences.

Check the batteries, and make sure that the + and – on the batteries are aligned according to the polarity diagram.

After it is conrmed that no mistake is made, the battery outlet can be connected to the machine.

This machine is to be charged by DC power supply and thus the + and – on the batteries must never be mis-

aligned. Otherwise, all electric apparatuses of the machine will be damaged.

All storage batteries of various types or brands should have their own appropriate charging units. Mismatching

di󰀨erent types of battery chargers may cause battery damage or explosion.

The maintenance service to this machine should be performed by trained and qualied technicians. Otherwise,

the machine could be damaged. Since each machine has been tested prior to delivery to guarantee operation on

system test, the professional technicians should make sure that all replacement parts or the repaired parts are on

xed connection after inspecting the defects or damages, and parts claimed for adjustment should be xed again

after the maintenance service.

The electric components of the machine could short circuit when in contact with water or in moist environments.

In order to ensure the desiccation of the components, the machine should be wiped and kept in a dry environment

after being used.

Ensure proper ventilation, especially in the area where the batteries are charged. The charger should be equipped

with an earth lead connecting through the power supply of three cord wire. For the sake of avoiding electrical shock

hazards, it is highly recommended that a leakage circuit-breaker be pre-installed.

Do not recharge the batteries unless the electric platform truck has been pulled out and the cell cover has been

removed (with the exception of the maintenance free battery), since gas bubbles might appear during the process

of recharging. Each time after recharging, remember to ret the cell cover to avoid the spilling of acid liquid.

Do not put any article on the batteries!

Do not put any article on the handlebar!

While cleaning the machine, do not run water into the air inlet of the lift pump!

Safe and economical operation of the machine is only possible if the machine operators are thoroughly familiar

with the signs and contents on this Operator’s Manual. Failure to do so could be harmful.

This machine is inappropriate for cleaning rough oors and slopes; Operators cannot sit on the machine while

operating it in these circumstances.

Be aware not to have your hands, legs, or loose clothing in contact with the rotating part of the machine.

Put warning signs on the surrounding area during operation to inform the operator and others that the oor could

be wet with water or detergents.

Follow safety rules at all times during the process of transportation of this large machine.

CAUTION

Avoid starting the machine or charger where combustible gas or liquid is available.

Avoid laying or placing the machine where combustible gas or liquid is available.

DIAGRAMS OF THE MACHINE

1. Handlebar

2. Control Panel

3. Suction Motor Button (b)

4. Brush Motor Button (c)

5. Power Switch

6. Timer

7. Socket for Charger

8. Squeegee Height Adjusting Handle

9. Manual Pressurized Handle

10. Brush Pedal

11. Guard Wheel

12. Fixed Handle of Squeegee

13. Squeegee

14. Regulating Handle of Squeegee

15. Water Suction Pipe

16. Water Drain Out Pipe

17. Water Valve

18. Metal Frame

19. Wheel

20. Brush

21. Clean Water Filtration

22. Water Level Indicator

23. Solution Tank

24. Dirty Water Tank

25. Dirty Water Tank Cover

a. Battery Indicator

b. Suction Motor Button

c. Brush Motor Button

d. Brush Install and Release Button

e. Rate Regulation (slow) Button

f. Rate Regulation (fast) Button

g. Rate Indication

h. Indication of Operation of Brush

Motor

i. Indication of Operation of Suction

Motor

FUNCTIONS AND NOTES

FUNCTION

DP-SCRUB20 is suitable for ceramic tile ooring, marble ooring, epoxy ooring, PVC ooring, diamond ooring, terrazzo

ooring, concrete ooring and hard oor cleaning. It has an 18-inch brush or pad driver to clean the oor, and the dirty

water will be sucked into a recovery tank by the squeegee. Cleaning is nished after passing over the oor one time. The

best feature of this machine quick dirt removal from the oor and it only requires one person.

ATTENTION

1. This machine is a high-e󰀩ciency, hard oor scrubber with clean and suction function, but no sweep function. In order

to avoid any tangling and blockage, sweep the oor before operation.

2. This machine is suitable for smooth, hard oor cleaning. If you attempt to clean tile oor with gaps or a rough marble

oor, although this scrubber can remove dirt, it can not absorb the dirty water completely as it would on a smooth

oor.

3. This machine is designed for smooth, hard oors. In order to avoid any potential risk, do not walk and operate on an

inclined plane.

4. Store and park the machine on the horizontal surface. Inexperienced people are forbidden to operate the machine.

5. Do not start or store the machine in an area with ammables, explosives, and chemical medicine.

6. Operator is forbidden to wear slippers or be barefoot.

7. Do not put hands or feet under the moving brush pad.

8. Keep the electrical control parts away from water and any other liquid, it is useful to wipe the machine with a wet

cleaning cloth.

9. Maintenance and amendment should be done by professional personnel.

FUNCTIONS AND NOTES

Battery-powered and equipped with an automatic walking device, The DP-SCRUB20 is a professional oor-cleaning

machine with following characteristics:

1. Simple operation

All actions including accelerating, stopping or retreating can be conducted by operating on the same handlebar. When

this machine retreats to its limiting position, its emergency stop switch will drive the machine in the opposite direction

after being pressed by the operator, so as to prevent the operator from being injured.

2. Power indication

Power can be indicated by di󰀨erent colored LCD, so that the operator is informed of the work load.

3. Convenient maintenance

The recovery tank is detachable, you can take it o󰀨 from the machine, which is convenient for cleaning. You can rinse

the lter by screwing the oating frame. Or you can drain out the water in the solution tank separately, which is conve-

nient for machine maintenance.

4. The dirty water tank cover is transparent, for easily checking tank levels. The transparent water level pipe clearly

shows the water level. The suction motor is xed under the dirty water tank for silent cleaning.

5. Pressurized function makes cleaning much easier, even for a oor with heavy dirt.

6. Convenient for maintenance

Squeegee replacement is quick and convenient.

Loosen the two xed squeegee knobs in the suction squeegee, pull o󰀨 the suction hose connection, then take o󰀨 the

suction part. Replace the back squeegee by loosening the fastener. Reverse the upper and lower to reuse the squee-

SPECIFICATIONS

MODEL

WORKING WIDTH OF BRUSH DISK (in)

WORKING WIDTH OF SQUEEGEE (in)

SOLUTION TANK CAPACITY (gal)

RECOVERY TANK CAPACITY (gal)

BRUSH SPEED (rpm)

BRUSH PRESSURE (lbs)

VOLTAGE (V)

SUCTION MOTOR (W)

BRUSH MOTOR (W)

MAGNETIC VALVE POWER (W)

BATTERY CAPACITY (AH)

WEIGHT (lbs)

TRANSPORTATION PACKAGE SIZE (in.)

DP-SCRUB20

200

24V 550W

24V 750W

24V 12W

2x12V / 100

238

51x25x40

BEFORE FIRST USE

1. In order to avoid harmful interference, the machine

should be removed from the package carefully and

the accompanying documents and spare parts

should be checked with great care.

2. Only after having a full understanding towards the

content of operator’s manual, the operator can

handle this machine. (A specic person should be

assigned to operate this machine)

3. The sales engineer or distributor will introduce how

to control the handle bar.

4. Align the battery and make sure that the batteries

and output device are correctly connected. Never

make a mistake on the polarity of the battery. The

batteries can be connected with the power only

after the connection of batteries is conrmed to be

right. (This operation can be carried out only after

the on-spot inspection has been made by the sales

engineer.)

5. Connect the squeegee to its frame, then screw

down xed handle and connect the tube to the

machine connection.

6. Take out the brush disk or needle bed and then

choose a proper brush disk or cleaning pad to

prepare for installation in accordance with the oor

condition.

7. With the lock open, the function test is carried on to

observe whether the power display and function keys

are normal. Only after further tests show nothing

wrong, the next operation can be implemented.

8. Pour water into the solution tank and then add proper

amount of cleaners; install the brush disk.

9. Loosen brake pedal.

10. Turn on power switch.

11. Lay down the squeegee and brush disk.

12. Start the suction motor and brush motor.

13. Pull the water valve switch upwards to regulate the

water output.

14. The clean-out operation can be carried out by push-

ing forward the control handle as well as adjusting

the walking rate.

15. After cleaning, the brush motor and water absorption

motor should be turned o󰀨 one after another.

16. Uplift the brush disk, squeegee and drain the dirty

water out. The machine should be cleaned and main-

tained according to requirements on the operator’s

manual if a whole day’s work is nished.

17. Move the machine to the parking place, turn o󰀨 the

power and push down on the brake pedal.

New machines should be operated according to the following procedures during its rst use.

(The operation should be implemented under the instruction of the sales engineer assigned by the company or agent)

OPERATION AND MAINTENANCE

1. Before operating, big pieces and dust on the ground should be removed. Operation should never be carried out until

no dirt, block, and wastepaper could be found on the ground, and all those procedures will help to increase the work

e󰀩ciency and protect the machine.

2. Insert the activation key into the start switch and rotate it to “1” (Seen in gure1) to check the battery capacity. Op-

eration should never be carried out until the green light turns on (seen in gure2) to indicate the full capacity of the

battery.

3. Fill the solution tank with clean water, add detergent according to the oor status. There are 2 ways for water lling

(see gure 3)

Green light x4

Green light x3

Green light x2

Green light x1

Red light ash

Battery power 100%

Battery power 80%

Battery power 60%

Battery power40%

Battery needs to be charged

4. Lift the brush pedal to lower the brush disk down to the ground. (Seen in gure4)

Lift the squeegee handle to lower the squeegee down to the ground. (Seen in gure5)

5. Operate the switches to control the brush and suction motor.

n suction motor on only - use for water sucking.

n brush on only - clean a oor with heavy dirt

n both switches on - dual cleaning.

6. Use pressurized function when cleaning heavy dirt. Lifting the handle

gives the brush more pressure on the oor. Regress to get back to

normal. (See gure 6)

7. Control the clean water ow rate by operating the water valve knob

according to di󰀨erent oor situations. This makes for high-e󰀩ciency

cleaning and no waste by properly consuming detergent.

(see gure 7)

OPERATION AND MAINTENANCE (CONT.)

Method: Take the waste pipe out of the clip, open the

cap of the tube, discharge sewage to the sewer and

clean the recovery tank.

(Seen in gure 9)

B. If the water level of the recovery tank is not too high and

it’s not bubbling, the connection between squeegee and

hose should be checked for clogs. In this case, the wa-

ter sucker will recover normal after being cleaned.

C. If the water level of recovery tank is not so high but

it is bubbling too much, that indicates that excessive

cleansers have been added or the cleanser you used

is a bubble-productive one. The water absorption motor

recovers only after enough bubble-dispelling agents are

put into the recovery tank.

D. Remove the upper cover (see in gure 10), start up the

suction motor, and make sure that the suction intake is

normal. If the suction is too weak, check the seal and

whether the oater is jammed (Seen in gure 10).

8. With the regulating handle of squeegee, increase or de-

crease the angle between the squeegee and the oor.

The suction of dirt would be e󰀩cient with a suitable

included angle.(see gure8)

9. Regulating the pressure between the squeegee and the

oor

n screw the small casters up to keep them from

touching the oor when the squeegee is working,

then adjust the included angle between the squee-

gee and oor to have the best working status for the

squeegee.(the included angle is 90° between the

rubber blade and oor).

n screwing the casters down keeps them on the oor

when the squeegee working. Keep adjusting the

casters until the squeegee is working e󰀩ciency.

n screw the casters up a bit, to give the squeegee the

best working e󰀩ciency (see gure 8).

10. If there is still cumulation after one way cleaning on a

rough oor, just lift up the squeegee and switch on the

suction motor, repeat the sucking in that area.

11.Problems occurred while adjusting the water suction.

During the operation, you should stop the machine and

check it immediately if the suction motor sounds abnor-

mal, or if the squeegee can not suck or absorb water at

all.

A. When the water level rises to the highest point (the

bobber can touch the cap), the sewage should be dis-

charged.

OPERATION AND MAINTENANCE (CONT.)

Deep grooves may cause incomplete cleaning,

please dispose separately.

Figure 9

OPERATION AND MAINTENANCE (CONT.)

12. Method for replacing the brush disk

A. Installation of the brush pad: Put the brush pad under

its cover (If the dial is used, the brush pad should be

installed on the dial, then put the brush pad under its

cover.) Lay down the brush pedal and align the brush

head with the brush clip. Then press, the brush disk will

be installed automatically with the running of the motor.

And then you can carry out your operation as usual.

B. Removal of the brush pad: There are two ways to

remove the brush pad:

The rst way is to step on the brush pedal after the work

(Uplift the brush pad), then turn o󰀨 the brush switch. At

this time, the brush pad will be removed automatically

after the motor stops running. The second way is to

press, and then the brush pad should be removed auto-

matically in the condition that the brush pedal is stepped

on.

13. Method for replacing the batteries

n turn o󰀨 all the switches, lift o󰀨 the dirty water tank

(see gure11)

n loosen the strap of the batteries, discharge the

connecting cables, replace the batteries separately.

14. Maintenance of the squeegee

As a major component of the machine, the squeegee

will be worn away due to friction between the glue bars

and the ground during operation. In case it is not e󰀨ec-

tive, the following procedures should be conducted:

A. Check whether there is anything in the rubber scraper;

(Prepare a towel to wipe the dirty rubber blade at any

time)

B. Check whether the joint of the squeegee and hose is

clogged up by the small pieces. (Remove the connection

of hose or squeegee to clean the clog.)

C. Check whether the angle between the scraper and

ground is proper; if not, you can adjust the angle by

regulating the hand wheel. (Seen in gure8)

D. Check the wearing condition of the scraper edge. If the

wearing condition is so serious that the adjustment will

not work, turn over the rubber blade and use another

side of it. (see gure 12) If another side is also worn out,

it has to be replaced by new rubber blade.

Note: If the brush pad is in the process of being

raised, the brush motor should not be started up

arbitrarily; otherwise, the brush disk will be

removed automatically.

Figure 12

15.Daily upkeep when operation is nished:

n clean the machine surface with a wet and dry cloth, and

open the water tank cover to check and make sure there

is no damage with the inside seal.

n pumping out the dirty water from the pollution tank,then

add more clean water to wash the inside again.

n uplift the brush and the squeegee, pack the machine in

a dry, at place without combustible gas, combustible

liquid, chemicals, or re.

n if unused for a period of time, please disassemble the

battery from the machine and clean the tanks. Cover the

opening of the tank cover with a dust cloth.

16.Ensure the clean water tank is clean. Cumulation may

cause a blockage. Clean the lter weekly to ensure the

water pipe expedite when in operation (see gure 13)

For the battery, you should keep charging as per the

instruction in the clause <battery maintenance and

charging> even though the battery is disassembled

from the machine.

MAINTENANCE AND CHARGE

OF BATTERY

This machine is battery-powered and thus the quality of

the battery will directly a󰀨ect the function of the machine.

Please use the battery recommended by our company or

other high-quality power batteries.

(Never use any automotive battery.)

In order to adapt itself to the requirements of various work-

ing conditions, battery 12V×2/100AH can be used in this

machine. Please choose proper batteries according to your

demands. Except for the di󰀨erence in capacity, the batter-

ies can be classied in two main categories: maintenance

battery and maintenance-free battery according to their

nature.

As an open type battery, a great deal of vapor bubbles

will be produced when charging the maintenance battery.

Therefore, the battery chamber cover should be taken o󰀨

every time it is being charged. The liquid height of the

electrolyte should be often checked. If it is lower than a

specied height, distilled water should be added in time.

Tabla de contenidos

Otros manuales de Depurador de DiamaPro Systems

DiamaPro Systems

DiamaPro Systems AS-500 Manual de usuario

DiamaPro Systems

DiamaPro Systems AS-1000 Manual de usuario

Manuales populares de Depurador de otras marcas

Olympus

Olympus M200H Manual de usuario

Clarke

Clarke BEXT 100H Manual de instalación y funcionamiento

JOHNY VAC

JOHNY VAC JVC70BCT Manual de usuario

RCm

RCm Elan Series Manual

Kärcher

Kärcher B 120 W Manual de usuario

Truvox

Truvox Orbis MotorScrubber 20 Manual de usuario

Numatic

Numatic TTB 4045/100 Manual de usuario

U.S. Products

U.S. Products PEX 500-C-TICK Instrucciones de funcionamiento

Mclennan

Mclennan C510 Manual de usuario

Tennant

Tennant T20 LPG Manual de usuario

Columbus

Columbus ARA 66 BM 100 Manual de usuario

Numatic

Numatic TTV 678G / 300T Manual de usuario

American-Lincoln

American-Lincoln 505-945 Manual de usuario

FIORENTINI

FIORENTINI ET 65-75 Manual de usuario

Floorpul

Floorpul ruby 48 blt Guía del usuario

Onyx

Onyx RX-34 Manual de usuario

Dustbane

Dustbane Hurricane 400 Manual de usuario

Sana

Sana EUJ-702 Manual de usuario