Note: The default isOFF, set this option to ON only if this STBis
connected to an activeantenna which amplifies thereceived RF signal,
otherwise please set it to OFF .
2.2.1.2 Country Setting
Set the country forAuto Scan, Manual Scanand Time Zone.
Note: Change toCountry Setting will automatically change the
default Time Zone and set the defaultFrequency and Bandwidth for
Auto Scan.
2.2.1.3 OSD Language
Set the On ScreenDisplay Language.
2.2.1.4 Audio Language
Set the audio language forwatching program.
2.2.1.5 Subtitle Language
Set the language fordisplaying subtitle.
2.2.1.6 LCN
Set the Logical Channel Numberto on or off.
Note: LCNis a number thatuniquely identifies a logicalchannel,
NOTE-Always set to ON
2.2.1.7 Daylight Saving/Region Setting/TimeZone
Allows you to enable or disable daylight saving. If you know the region of
your location,select an appropriateRegion Setting or set the Time Zone
offset manually.
2.2.1.8 Auto Scan
Press <RED> button tostart Auto Scan. See section1.2.1 for details.
2.2.1.9 Manual Scan
Press <GREEN> button tostart Manual Scan. See section1.2.2 for details.
2.2.2 TV Setup
Setup the display modefor TV.(Optional) See Figure 3.
2.2.2.1 TV Format
Set display formatfor sizing screen, such as 4:3LB, 4:3PS,
16:9PB,16:9 FIT.
4:3LB(LetterBox): Typicallyfor wide screencontent displays on
conventional 4:3 TVwith black barsabove and belowthe picture.
4:3PS(PanScan): Typicallyfor wide screencontent displays on
conventional 4:3 TVwith left andright edges cropped.
16:9PB(PillarBox)/16:9 FIT: Typicallyfor wide screen 16:9TV.
2.2.2.2 TV Mode
Set PAL,NTSC or AUTO for display. AUTOwill switch PAL or NTSC
by program content.This setting should bematched with user'sTV.
2.2.2.3 OSD Transparency
Set the On ScreenDisplay transparency.1 is the most transparent.
2.2.2.4 Banner DisplayTime
Set Banner displaystime. Banner doesn'tdisappear when setas
Always and disappears at timeout when set as othervalues.
2.2.2.5 Video Output
Set the video outputmode to TV.
2.2.2.6 Video Enhancement
Set the VideoEnhancement. See Figure4.
(1) Press <Up/Down> button toselect Video Enhancementoption.
(2) Press <Left/Right> buttonto setVideo Enhancement.
(3) Press <Up/Down> button toselect Flesh Toneor Black/White
Expansion.
(4) Press <Left/Right> buttonto setFlesh Toneand Black/White
Expansion.
2.2.3 Password
Set password formenu lock orchannel lock orcensorship lock.And the
user can changepassword here, thedefault PIN Codeis 6666.
2.2.3.1 Menu Lock
Lock the menusby password.
2.2.3.2 Channel Lock
Lock the channelwhich has beenset to lockstatus when turningon the
Channel Lock. Please seesection 2.3.1.2 for details.
2.2.3.3 Censorship Lock
Lock the programby password andcensorship threshold.
The censorship infois in programcontent. Under thecensorship rating,
user has to enterthe right password forwatching program.
2.2.3.4 Change Password
Tochange the PINcode, select thisoption, press <Left/Right>button
to trigger changingpassword and <0~9>buttons to enterold password,
new password and confirm new password.If successful,thePIN Code
Changed message will bedisplayed, otherwise thePIN Code Error
message will be displayed.
Figure 3. TVSetup
4
Figure 4. VideoEnhancement
SETUP. TV Setup 01/01/200800:19
TV Format
TV Mode
4:3LB
PAL
Move SwitchExit
OSDTransparency 6
Banner Display Time
Video Output
Video Enhancement
3S
OFF
CVBS+RGB
5761
Flesh Tone OFF
Move Switch Exit
Black/White Expansion OFF
Note:Most settings are automatically set upon scanning the unit in.
