DFI AM75-TC Manual de usuario

AM75-EC

AM75-TC

Rev. A+

System Board

Users Manual

48110117

Copyri ht

This publication contains information that is protected by copyright.

No part of it may be reproduced in any form or by any means or

used to make any transformation/adaptation without the prior

written permission from the copyright holders.

This publication is provided for informational purposes only. The

manufacturer makes no representations or warranties with respect to

the contents or use of this manual and specifically disclaims any

express or implied warranties of merchantability or fitness for any

particular purpose. The user will assume the entire risk of the use or

the results of the use of this document. Further, the manufacturer

reserves the right to revise this publication and make changes to its

contents at any time, without obligation to notify any person or

entity of such revisions or changes.

Trademarks

Microsoft® MS-DOS®, WindowsTM, Windows® 95, Windows® 98,

Windows® 98 SE, Windows® ME, Windows® 000 and Windows

NT® 4.0 are registered trademarks of Microsoft Corporation. AMD,

AthlonTM and DuronTM are registered trademarks of Advanced Micro

Devices, Inc. VIA is a registered trademark of VIA Technologies, Inc.

Award is a registered trademark of Award Software, Inc. Other

trademarks and registered trademarks of products appearing in this

manual are the properties of their respective holders.

Caution

To avoid damage to the system:

 Use the correct AC input voltage range.

To reduce the risk of electric shock:

 Unplug the power cord before removing the system chassis

cover for installation or servicing. After installation or servicing,

cover the system chassis before plugging the power cord.

Battery:

 Danger of explosion if battery incorrectly replaced.

 Replace only with the same or equivalent type recommend by

the manufacturer.

 Dispose of used batteries according to the battery

manufacturers instructions.

Joystick or MIDI port:

 Do not use any joystick or MIDI device that requires more than

10A current at 5V DC. There is a risk of fire for devices that

exceed this limit.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a residential

installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the

following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and the receiver.

 Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

 Consult the dealer or an experienced radio TV technician for

help.

Notice:

1. The changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority

to operate the equipment.

. Shielded interface cables must be used in order to comply with

the emission limits.

Notice

This users manual contains detailed information about the system

board. If, in some cases, some information doesnt match those

shown in the multilingual manual, the multilingual manual should

always be regarded as the most updated version. The multilingual

manual is included in the system board package.

To view the users manual, insert the CD into a CD-ROM drive. The

autorun screen (Main Board Utility CD) will appear. Click Users

Manual.

System Board

This users manual is for the AM75-EC and AM75-TC system

boards. The differences between these boards are shown below.

AM75-EC

(VIA® KM133)

AM75-TC

(VIA® KM133A)

Chipset

CPU

JP10

(CPU FSB select)

VT8365/686B

100MHz FSB

VT8365A/686B

100/133MHz FSB

Table of Contents

Chapter 1 - Introduction

1.1 Features and Specifications..................................................................................

1. Package Checklist.........................................................................................................

Chapter 2 - ardware Installation

.1 System Board Layout .............................................................................................

. System Memory.............................................................................................................

.3 CPU Frequency Ratio...............................................................................................

.4 Jumper Settings for Clearing CMOS Data..........................................

.5 Jumper Settings for the Onboard Audio Codec...........................

.6 Jumper Settings for Selecting the CPUs Front Side Bus........

.7 Jumper Settings for Selecting the USB Power...................................

.8 Ports and Connectors.............................................................................................

Chapter 3 - Award BIOS Setup Utility

3.1 The Basic Input/Output System.....................................................................

3.1.1 Standard CMOS Features.............................................................

3.1. Advanced BIOS Features..............................................................

3.1.3 Advanced Chipset Features ......................................................

3.1.4 Integrated Peripherals.........................................................................

3.1.5 Power Management Setup............................................................

3.1.6 PnP/PCI Configurations....................................................................

3.1.7 PC Health Status...................................................................................

3.1.8 Frequency/Voltage Control............................................................

3.1.9 Load Fail-Safe Defaults.....................................................................

3.1.10 Load Optimized Defaults..............................................................

3.1.11 Set Supervisor Password...............................................................

3.1.1 Set User Password..............................................................................

3.1.13 Save & Exit Setup.................................................................................

3.1.14 Exit Without Saving..............................................................................

3. Updating the BIOS.....................................................................................................

Introduction



Chapter 4 - Supported Softwares

4.1 Desktop Management Interface.....................................................................

4. VIA Hardware Monitor............................................................................................

4.3 VIA Service Pack..........................................................................................................

4.4 Audio Drivers and Software Application...............................................

4.5 Graphics Drivers............................................................................................................

4.6 Microsoft DirectX 7.0 Driver.............................................................................

4.7 Drivers and Utilities Installation Notes.....................................................

Appendix A - Using the Suspend to RAM

Function

A.1 Using the Suspend to RAM Function........................................................

Appendix B - System Error Messages

B.1 POST Beep.......................................................................................................................

B. Error Messages..............................................................................................................

Appendix C - Troubleshooting

C.1 Troubleshooting Checklist....................................................................................



Introduction

1.1 Features and Specifications

1.1.1 Features

Chipset

 VIA® KM133 - VT8365 and VT8 C686B (AM75-EC)

 VIA® KM133A - VT8365A and VT8 C686B (AM75-TC)

Processor

The system board is equipped with Socket-A for 46 -pin PGA

processor. It is also equipped with a switching voltage regulator that

automatically detects 1.100V to 1.850V.

 AM75-EC

- AMD AthlonTM/DuronTM 100MHz ( 00MHz DDR) FSB pro-

cessor (600/650/700/750/800/850/900/950MHz, 1GHz,

1.1GHz, 1. GHz or future processors)

 AM75-TC

- AMD AthlonTM/DuronTM 100/133MHz ( 00/ 66MHz DDR)

FSB processor (600/650/700/750/800/850/900/950MHz,

1GHz, 1.1GHz, 1. GHz or future processors)

System Memory

 Supports up to 1.5GB using VCM (Virtual Channel Memory) or

PC SDRAM DIMM (unbuffered or registered).

- Registered DIMM - PC-100 only.

 Three 168-pin DIMM sockets

 Uses x64 PC SDRAM, 3.3V

- PC-100 SDRAM DIMM for 100MHz memory bus

- PC-133 SDRAM DIMM for 133MHz memory bus

 L cache memory

- DuronTM processor: built-in 64KB Level pipelined burst

cache

- AthlonTM processor: built-in 56KB Level pipelined burst

cache

Chapter 1 - Introduction

Introduction



Expansion Slots

The system board is equipped with 1 universal AGP slot, 4

dedicated PCI slots and 1 shared PCI/ISA slot.

AGP is an interface designed to support high performance 3D

graphics cards. It utilizes a dedicated pipeline to access system

memory for texturing, z-buffering and alpha blending. The universal

AGP slot supports AGP x with up to 533MB/sec. bandwidth and

AGP 4x with up to 1066MB/sec. bandwidth for 3D graphics

applications. AGP in this system board will deliver faster and better

graphics to your PC.

Onboard Graphics Features

 Integrated Savage4 D/3D/Video accelerator

- Shares MB to 3 MB of the system memory

- Optimized Shared Memory Architecture (SMA)

- Full AGP 4x, including sideband addressing and execute mode

- High quality DVD video playback

 3D rendering features

- 3 -bit true color rendering

- MPEG- video textures

 D hardware acceleration features

 Motion video architecture

 Software drivers

- Windows® 95/98/ 000/ME

- Windows NT® 4.0

DIMMs

MBx64

4MBx64

8MBx64

Memory Size

16MB

3 MB

64MB

DIMMs

16MBx64

3 MBx64

64MBx64

Memory Size

1 8MB

56MB

51 MB

Important:

 PC-100 SDRAM DIMM is supported when used with

100M z FSB processor.

 PC-133 SDRAM DIMM is supported when used with

100M z FSB or 133M z FSB processor.

 If you are using more than one DIMM, make sure you

insert the same type of DIMMs into the DIMM sockets.

Using different types (VCM or PC SDRAM) of DIMMs may

cause problems.



Introduction

Onboard Audio Features

 Supports Microsoft® DirectSound / DirectSound 3D

 AC97 supported with full duplex, independent sample rate con-

verter for audio recording and playback

ATX Double Deck Ports (PC 99 color-coded connectors)

 Two USB ports

 One NS16C550A-compatible DB-9 serial port

 One DB-15 VGA port

 One SPP/ECP/EPP DB- 5 parallel port

 One mini-DIN-6 PS/ mouse port

 One mini-DIN-6 PS/ keyboard port

 One game/MIDI port

 Three audio jacks: line-out, line-in and mic-in

Connectors

 One connector for additional external USB ports

 One connector for 1 external serial port

 One connector for IrDA interface

 Two IDE connectors

 One floppy drive interface supports up to two .88MB floppy

drives

 One ATX power supply connector

 One Wake-On-LAN connector

 One Wake-On-Ring connector

 CPU, chassis and second chassis fan connectors

 Three internal audio connectors (AUX-in, CD-in and TAD)

PCI Bus Master IDE Controller

 Two PCI IDE interfaces support up to four IDE devices

 Supports ATA/33, ATA/66 and ATA/100 hard drives

 PIO Mode 3 and Mode 4 Enhanced IDE (data transfer rate up

to 16.6MB/sec.)

 Bus mastering reduces CPU utilization during disk transfer

 Supports ATAPI CD-ROM, LS-1 0 and ZIP

Introduction



IrDA Interface

The system board is equipped with an IrDA connector for wireless

connectivity between your computer and peripheral devices. It

supports peripheral devices that meet the HPSIR and ASKIR

standard.

USB Ports

The system board supports 4 USB ports. Two onboard USB ports

are located at the ATX double deck ports of the board. The J19

connector on the system board allows you to connect the optional

3rd and 4th USB ports. These optional USB por ts, which are

mounted on a card-edge bracket, will be provided as an option.

USB allows data exchange between your computer and a wide

range of simultaneously accessible external Plug and Play peripherals.

BIOS

 Award BIOS, Windows® 95/98/ 000/ME Plug and Play compat-

ible

 Supports SCSI sequential boot-up

 Flash EPROM for easy BIOS upgrades

 Supports DMI .0 function

 Mbit flash memory

 Vcore and CPU external bus clock selectable in the BIOS

Desktop Management Interface (DMI)

The system board comes with a DMI .0 built into the BIOS. The

DMI utility in the BIOS automatically records various information

about your system configuration and stores these information in the

DMI pool, which is a part of the system board's Plug and Play

BIOS. DMI, along with the appropriately networked software, is

designed to make inventory, maintenance and troubleshooting of

computer systems easier. Refer to chapter 4 for instructions on using

the DMI utility.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Placa madre de DFI

DFI

DFI OT951-D Series Manual de usuario

DFI

DFI G5C100-B Manual de usuario

DFI

DFI CA64-TN Manual de usuario

DFI

DFI G7S620-N Manual de usuario

DFI

DFI SD630-H110 Manual de usuario

DFI

DFI CS331-C246 Manual de usuario

DFI

DFI 855GME-MGF Manual de usuario

DFI

DFI SB332-C Manual de usuario

DFI

DFI ADS310-R680E Series Manual de usuario

DFI

DFI Infinity NF series Manual de usuario

DFI

DFI NB71-SC Manual de usuario

DFI

DFI LanParty LT P35 Manual de usuario

DFI

DFI NB72-SC Manual de usuario

DFI

DFI 945G-TMGF Manual de usuario

DFI

DFI LanParty DK P35 series Manual de usuario

DFI

DFI CA230-BF Manual de usuario

DFI

DFI PE11-TC Manual de usuario

DFI

DFI ADS101 Manual de usuario

DFI

DFI NS30-SC/SL Manual de usuario

DFI

DFI GH551 Manual de usuario

DFI

DFI G586SPB AIO Manual de usuario

DFI

DFI CD951-C Series Manual de usuario

DFI

DFI COM330-B Manual de usuario

DFI

DFI K6BV3+ Manual de usuario

Manuales populares de Placa madre de otras marcas

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario