DFI WM342-KD Series Manual de usuario

1

WM342-KD Series Installation Guide

•

One WM342-KD330/WM342-KD331 system unit

•

1 SATA data cable

•

1 CPU cooler and 1 system fan

• HDD mounting screws

•

1 Quick Installation Guide

•

1 CD disk includes:

- Drivers / Manual

Package Contents

Panel

Front View

DFI reserves the right to change the specications at any time prior to the product's release. For the latest revision and for a more

details of the installation process, please refer to the user's manual on the website.

www.d.com

Rear View (WM342-KD330/WM342-KD331)

Expansion Slot

DVI-D

(DVI-I connector)

DP++

SATA

Drive Bay

for KD331:

LAN 3

LAN 4

or

for KD330:

Line-out

Mic-in

LAN 1 LAN 2

USB 3.0 1-4

PS/2 KB/MS

USB 2.0 1-2

COM1

VGA

Power LED (green)

HDD LED (red)

Power Button

AC Power

Socket

All manuals and user guides at all-guides.com

all-guides.com

2

Opening the Chassis

Please observe the following guidelines and follow the procedure to open

the system.

1. Make sure the system and all other peripheral devices connected to it have

been powered off.

2. Disconnect all power cords and cables.

3. Remove the top cover by uninstalling the thumb screws.

Thumb screw

All manuals and user guides at all-guides.com

3

Installing a DIMM

1. Align the notch on the DIMM with the tab in the DIMM connector.

2. Press down on the DIMM until the release tabs spring back to secure the

DIMM in place.

Notes:

1. The WM342-KD330 is equipped with two or four DDR4 (dual channel) sockets depending

on the chipset.

2. The WM342-KD331 is equipped with four DDR4 (dual channel) sockets.

The installed DIMM

All manuals and user guides at all-guides.com

4

Installing 2.5" SATA Drive

1. Remove the thumb screws that secure the HDD drive bay to the chassis and

remove the drive bay.

Thumb screw

The system can accommodate two 2.5" SATA installation. Use the following proce-

dure to install a SATA drive onto the system.

All manuals and user guides at all-guides.com

5

2.5" SATA Drive

2. Secure the hard drive to the drive bay. Align the mounting holes on the SATA

drive with the mounting holes on the HDD drive bay. Use 4 mounting screws

to install the hard drive onto the HDD drive bay.

Mounting screw

Drive bay

All manuals and user guides at all-guides.com

6

3. Slide the HDD drive bay back to the system and secure it with the thumb screws.

4. Connect the SATA data cable and power cable to the connectors on the SATA drive.

And connect the other end of the SATA data cable on the motherboard.

SATA port

SATA data and

power cable

All manuals and user guides at all-guides.com

all-guides.com

7

Installing a PCI or PCIe Expansion Card

Use the following procedure to install a PCIe expansion card:

1. Remove the mounting screws to uninstall the card slot bracket.

2. Insert the expansion card in the connector on the

motherboard

and press

down until secured.

PCIe card

Screw

Card slot bracket

All manuals and user guides at all-guides.com

8

Rear View

PCIe card

3. Reinstall the card slot bracket to secure the expansion card in place.

Notes:

1. The WM342-KD330 is equipped with one PCIe x16 and one PCI slots.

2. The WM342-KD331 is equipped with one PCIe x16 and one PCIe x4 slots.

All manuals and user guides at all-guides.com

9

The system is equipped with one M.2 socket, supporting both the M.2

22x60mm and 22x80mm (key M) form factors. Use the following procedure

to install an M.2 card:

1. To install an M.2 type 2260 card, please install the standoff at the 60mm

mounting position rst.

2. Align the notch at the edge of the M.2 card with the key in the connector.

3. Insert the M.2 card into the connector.

Installing an M.2 Card

M.2 card

Note:

The M.2 slot is available in WM342-KD331 (both Intel® C236 and Q170 chipsets); the SKU

with Intel® C236 chipset supports Intel® Optane™ memory.

Standoff

All manuals and user guides at all-guides.com

10

The system board is equipped with one Mini PCIe slot that uses USB, PCI

and mSATA signals.

1. Grasp the Mini PCIe card by its edges and align the notch in the

connector of the PCIe card with the notch in the connector on the

system board.

2. Push the Mini PCIe card down and use the provided mounting screws to

secure the card on the system board.

Installing a Mini PCIe Card

Note:

The Mini PCIe slot is available in WM342-KD330 (only with Intel® Q170 chipset).

Mounting screw

All manuals and user guides at all-guides.com

Otros manuales para WM342-KD Series

1

Este manual sirve para los siguientes modelos

2

Tabla de contenidos

Otros manuales de De oficina de DFI

Manuales populares de De oficina de otras marcas

HP

HP m9060n - Pavilion - Elite Hoja de especificaciones

Asus

Asus E210 Series Manual de usuario

Dell

Dell Inspiron 600m Manual de usuario

Dell

Dell Inspiron 3662 Manual de usuario

TotalFlow

TotalFlow uFLO Manual de usuario

HP

HP Presario SV7000 - Desktop PC Manual de usuario

HP

HP ProDesk 400 G5 Manual

Logitech

Logitech MK320 Manual de usuario

Dell

Dell XPS 730 H2C Manual de usuario

Sony

Sony Vaio Series Manual de usuario

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Manual de usuario

Alto

Alto MD 250 Manual de usuario

Lenovo

Lenovo ThinkCentre Edge 72 Manual

Lenovo

Lenovo ThinkStation D20 Manual

Arbor Technology

Arbor Technology FPC-7800 Series Manual de usuario

Sony

Sony VAIO VGX-TP1 Series Manual de usuario

Asus

Asus Eee Box B204 Manual de usuario

Dell

Dell Optiplex 9010 All In One Manual de usuario