DFI ED700-EHL22I Manual de usuario

www.dfi.com

ED700-EHL22I

Fanless Embedded System

Quick Installation Guide

Package Contents

• 1 ED700/ED710-EHL System Unit

• Wall Mount Bracket

• Power Cord (Optional)

Front View

USB 3.0

LAN (2.5G)

LAN

COM 1 & 2

Grounding

Antenna Holes

Isolated COM1 & COM2 (support 2KV)

Isolated 6bit DI & 6bit DO (support 2KV)

DC-In (9~36V)

VGA

Quick Installation Guide | ED700-EHL22I 1

Product Overview

SIM Slot

USB 2.0

Antenna Holes

Side I/O view

Quick Installation Guide | ED700-EHL22I 2

Removing the Chassis Cover

Please observe the following guidelines and follow the instructions to open the system.

Make sure the system and all other peripheral devices connected to it have been

powered off.

2. Disconnect all power cords and cables.

Step 1:

The 5 screws on the bottom of the system are used to secure the cover to the chassis.

Remove the screws and put them in a safe place for later use.

Step 2:

Lift the cover to open the system.

The board can be easily accessed after the chassis cover is removed.

Quick Installation Guide | ED700-EHL22I 3

Installing an M.2 Card

Before installing the M.2 module into the M.2 socket, please make sure that the following

safety cautions are well-attended.

1. Make sure the PC and all other peripheral devices connected to it has been

powered down.

2. Disconnect all power cords and cables.

3. Locate the M.2 socket on the system board

4. Make sure the notch on card is aligned to the key on the socket.

5. Make sure the standoff screw is removed from the standoff.

M.2 Module M.2 Socket

Key

Stand-off

Notch

Quick Installation Guide | ED700-EHL22I 4

Please follow the steps below to install the card into the socket.

Step 2:

Press the end of the card far

from the socket down until

against the stand-off.

Step 3:

Screw tight the card onto the

stand-off with a screw driver

and a stand-off screw until

the gap between the card and

the stand-off closes up. The

card should be lying parallel to

the board when it’s correctly

mounted.

Step 1:

Insert the card into the socket

at an angle while making sure

the notch and key are perfectly

aligned.

M.2 Module M.2 Socket

Key

Stand-off

Notch

Quick Installation Guide | ED700-EHL22I 5

Installing the SO-DIMM Module

Before installing the memory module, please make sure that the following safety cautions are

well-attended.

1. Make sure the PC and all other peripheral devices connected to it has been powered

down.

2. Disconnect all power cords and cables.

3. Locate the SO-DIMM socket on the system board

4. Make sure the notch on memory card is aligned to the key on the socket.

Notch

Retention Notch

Key

Socket Top View

DDR4 SO-DIMM

Retention Clip

45°

Step 1

Step 2

Step 3

Quick Installation Guide | ED700-EHL22I 6

Notch

Retention Notch

Key

Socket Top View

DDR4 SO-DIMM

Retention Clip

45°

Step 1

Step 2

Step 3

Please follow the steps below to install the memory card into the socket.

Step 1:

Insert the memory card into the slot while

making sure 1) the notch and the key

are aligned, and 2) the non-connector

end rises approximately 45 degrees

horizontally. Press the card firmly into the

socket while applying and maintaining

even pressure on both ends.

Step 2:

Press the end of the card far from

the socket down while making sure

the retention notch and the clip align

as indicated by the dotted line in the

illustration. If the retention notch and the

clip do not align, please remove the card

and re-insert it. Press the card all the way

down.

Step 3:

The clips snap automatically and abruptly

to the retention notches of the card

sounding a distinctive click, and lock the

card in place. Inspect that the clip sits

in the notch. If not, please pull the clips

outward, release and remove the card, and

mount it again.

Quick Installation Guide | ED700-EHL22I 7

Installing an Antenna

Before installing the antenna, please make sure that the following safety cautions are

wellattended

1. Make sure the PC and all other peripheral devices connected to it have been

powered

down

2. Disconnect all power cords and cables.

Step 1:

There are antenna holes reserved on the front and left side of the system and covered by six

knockout tabs. Please remove the knockout tabs prior to installing an antenna.

Knockout tabs for antenna holes

Quick Installation Guide | ED700-EHL22I 8

Step 2:

Use a flathead screwdriver and apply a little extra force to detach a knockout tab until it

breaks off from the system.

Once the knockout tab is mostly detached, it will pretty quickly snap off, leaving you a nice

hole for installing an antenna.

Step 3:

Connect the internal cable to the board's antenna connector, screw the antenna connector

through the antenna hole with washers and nuts, and screw on the antenna as illustrated below.

Antenna ConnectorCableModule Connector NutWasher

Chassis Wall Antenna

Quick Installation Guide | ED700-EHL22I 9

Otros manuales para ED700-EHL22I

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de De oficina de DFI

Manuales populares de De oficina de otras marcas

HP m9060n - Pavilion - Elite Hoja de especificaciones

Asus

Asus E210 Series Manual de usuario

Dell

Dell Inspiron 600m Manual de usuario

Dell

Dell Inspiron 3662 Manual de usuario

TotalFlow

TotalFlow uFLO Manual de usuario

HP Presario SV7000 - Desktop PC Manual de usuario

HP ProDesk 400 G5 Manual

Logitech

Logitech MK320 Manual de usuario

Dell

Dell XPS 730 H2C Manual de usuario

Sony

Sony Vaio Series Manual de usuario

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Manual de usuario

Alto

Alto MD 250 Manual de usuario

Lenovo

Lenovo ThinkCentre Edge 72 Manual

Lenovo

Lenovo ThinkStation D20 Manual

Arbor Technology

Arbor Technology FPC-7800 Series Manual de usuario

Sony

Sony VAIO VGX-TP1 Series Manual de usuario

Asus

Asus Eee Box B204 Manual de usuario

Dell

Dell Optiplex 9010 All In One Manual de usuario