Dexter Laundry COIN COMPACT DRYER Manual de usuario
8514-046-001F
July 2013
OPERATOR’S MANUAL
for COIN COMPACT DRYER
The dryer ust not be stored or installed where it will be exposed to water and/or weather.
WARNING: For your safety the information in this manual must e followed to
minimize the risk of fire or explosion or to prevent property damage, personal
injury or death.
-Do not store or use gasoline or other flamma le vapors and liquids in the vicinity of
this or any other appliance.
-WHAT TO DO IF YOU SMELL GAS
-Do not try to light any appliance.
-Do not touch any electrical switch: do not use any telephone in your uilding.
-Clear the room, uilding or area of all occupants.
-Immediately call your gas supplier from a neigh or’s telephone. Follow the
gas supplier’s instructions.
-If you cannot reach your gas supplier, call the fire department.
Installation and service must e performed y a qualified installer, service agency or
the gas supplier.
You, the purchaser, ust post in a pro inent location instructions to be followed in the event the user s ells
gas. Consult your local gas supplier for procedure to be followed if the odor of gas is present.
Post the following
“For Your Safety”
caution in a pro inent location:
FOR YOUR SAFETY
Do not store or use gasoline or other fla able vapors or liquids in the vicinity of this or any other appliance.
FOR YOUR SAFETY
THIS MACHINE IS FOR DRYING ONLY FABRICS CLEANED IN WATER.
To
avoid possibility of fire, including spontaneous co bustion, do not dry oiled floor ops, ite s
containing foa rubber or si ilarly textured rubberlike aterials or any aterial on which you
have used a cleaning solvent or which contains fla able liquids or solids (such as gasoline,
kerosene, waxes, etc.)
It is i portant that you read this Manual and retain it for future reference.
For service or replace ent parts, contact the distributor in your area or:
Dexter Laundry, Inc
2211 W. Gri es
Fairfield, Iowa 52556, USA
2
French Language Warnings
AVERTISSEMENT. Assurez-vous de ien suivre les instructions données dans cette
notice pour réduire au minimum le risque d’incendie ou d’explosion ou pour éviter
tout dommage matériel, toute lessure ou la mort.
Ne pas entreposer ni utiliser d’essence ni d’autres vapeurs ou liquides infla ables dans
le voisinage de cet appareil ou de tout autre appareil.
I. QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ:
· Ne pas tenter d’allu er d’appareil.
· Ne touchez à aucun interrupteur. Ne pas vous servir des téléphones se trouvant
dans le bâti ent oú vous vous trouvez.
· Évacuez la pièce, le bâti ent ou la zone.
· Appelez i édiate ent votre fournisseour de gaz depuis un voisin. Suivez les
instructions du fournisseur.
· Si vous ne pouvez rejoindre le founisseur de gaz, appelez le service des
incendies.
L’installation et l’entretien doivent être assurés par un installateur ou un service d’entretien
qualifié ou par le fournisseur de gaz.
POUR VOTRE SÉCURITÉ
Ne pas enteposer ni utiliser d’essence ni d’autres
vapeurs ou liquides infla ables dan le voisinage
de cet appareil ou de tout autre appareil.
3
TABLE OF CONTENTS
Page No.
Warnings about use and operation ...................................................................................... 3
Installation Instructions ................................................................................................5, 6, 7
Dryer Shutdown .................................................................................................................10
Operating Instructions.........................................................................................................11
Preventative Maintenance Instructions................................................................................16
ILLUSTRATIONS
Figure 1 - Dryer Di ensions .................................................................................................4
Figure 2 - Vertical Clearance Di ensions ............................................................................6
Figure 3 - Dryer Exhausting ..................................................................................................9
WARNINGS ABOUT USE AND OPERATION
It is ABSOLUTELY ESSENTIAL that the dryer be grounded to a known earth (zero)
ground. This is not only for personal safety, but is necessary for proper operation.
KEEP SHIELDS, GUARDS AND COVERS IN PLACE. These safety devices are
provided to protect everyone fro injury.
A DRYER SHOULD BE CONNECTED TO POWER FOR THREE (3) MINUTES
before it is operated or before a progra change is ade. Operation or progra changes, which
occur during this "power up" period, are subject to loss in case of power interruption. After the
initial three inutes, all progra ed data is protected fro power interruptions of any length
and the custo er's individual cycle is protected up to 3 seconds. This is done without batteries.
LEAVE THE ELECTRICAL POWER TO THE DRYER ON AT ALL TIMES except
when necessary for service or other si ilar activities. The hour eter function adds only full
hours to its reading. If the power is shut off every night, any fraction of an hour of ti e that is on
the achine at that ti e will be lost. Turning the power off every night could also have so e
effect on the long-ter life of the e ory after a nu ber of years. Turning power off
occasionally won’t affect the unit.
THIS DRYER IS EQUIPPED WITH A MANUALLY RESETTABLE OVER-
TEMPERATURE THERMOSTAT located on the end of the burner housing below the gas valve.
Should the dryer cease to heat, reset the ther ostat by inserting a wooden (nonconductive)
pencil or dowel through the guide bushing in the cover. Should the ther ostat continue to trip,
the dryer ust be inspected by a qualified service person.
CHECK THIS THERMOSTAT WHEN INSTALLING DRYER to assure it is not
tripped. I pacts, such as rough handling in ship ent, ay trip the ther ostat. It ay be reset by
inserting a wooden (nonconductive) pencil or dowel through the guide bushing in the cover.
4
5
INSTALLATION AND OPERATING INSTRUCTIONS
This dryer may have een supplied as part of a washer/dryer stacked
appliance. If so, refer to the washer instructions for uncrating and hard
mounting the stacked unit to a concrete floor and o serve the dryer clearances
listed elow.
UNCRATING AND PLACING DRYER (Stand alone dryer unit):
Tools Required: ½ in. hex socket and ratchet driver, wood block 4 in. or 5 in. (102-127 )
thick, a knife and a groove joint pliers, which will open to 1 3/8 in. (35 ).
1. Re ove and discard stretch-wrap, posts, cap and inner packing.
2. The crate base is attached to the dryer by (4) cap screws driven upward fro below the crate
base. Re ove crate base fro dryer, by tipping dryer sidewise and place block under crate base
rail in center of dryer. Using a ratchet and ½ in. hex socket, re ove and discard (2) crating bolts
fro side, which is raised. Re ove block fro under crate base. Repeat for other side.
3. Install the leveling legs, which are shipped inside the dryer dru . Using a walking otion,
ove dryer sideways about 6 in. (152 ) off crate base. Tip dryer up and place block under
edge of dryer. Thread two leveling legs about two-thirds into the T-nuts on the base fro which
the crating bolts were re oved. Re ove block fro under dryer.
With a walking otion ove dryer co pletely off crate base. Discard crate base.
Tip dryer sidewise, as previously done, and place block under edge of dryer on raised side.
Thread leveling legs into nuts as was done for the first side.
Slide unit into position where it will be installed. Adjust leveling legs, using the groove joint
pliers, to level and align dryer with adjacent units.
DRYER INSTALLATION
1. CODE CONFORMITY: All co ercial dryer installations ust confor to the local and
national codes for the location of installation.
2. INSTALLATION CLEARANCES: This unit ay be installed at the following alcove
clearance.
I. Left Side 0
II. Right Side 0
III. Back 18 in. (457 ) clearance is necessary behind the otors to allow
servicing and aintenance.
IV. Front 48 in. (1220 ) to allow use of dryer.
6
V. Top Refer to figure labeled “Vertical Clearance Di ensions”.
AB. 0 clearance is allowable at the top; 4 in. (102 ) back fro the
front. However 1/4 in. (6 ) clearance should be allowed in case the
dryer needs oving.
C. 10 in. (254 ) clearance is required fro top at all other points.
VI. Floor If used as a stand alone dryer, this unit is intended to be installed upon an
elevated surface. The surface ust be of suitable strength to support 450
pounds (205 kg), and the dryer should be bolted or anchored to prevent
horizontal ove ent. The dryer ay be installed upon a co bustible
surface.
Refer to the label attached to the Belt Guard on the rear of the dryer for other installation
infor ation and start-up instructions.
7
3. MAKE-UP AIR. Adequate ake-up air, 440 CFM (12.5
3
/ in.), ust be supplied to
replace air exhausted by dryers on all types of installations. Provide a ini u of 1 sq. ft.
(.14
2
) ake-up air opening to outside for each dryer. This is a net require ent of effective area.
Screens, grills or louvers, which will restrict the flow of air, ust be considered. Consult the
supplier to deter ine the free area equivalent for the grill being used.
The source of ake-up air should be located sufficiently away fro the dryers to allow an even
airflow to the air intakes of all dryers. Multiple openings should be provided.
NOTE: The following considerations ust be observed for gas dryer installation where dry
cleaners are installed.
The sources of all ake-up air and roo ventilation air ove ent to all dryers ust be located
away fro any dry cleaners. This is necessary so that solvent vapors will not be drawn into the
dryer inlet ducts. Dry cleaner solvent vapors will deco pose in contact with open fla e such as
the gas fla e present in clothes dryers. The deco position products are highly corrosive and will
cause da age to the dryer(s) ducts and clothes loads.
4. ELECTRICAL REQUIREMENTS. The electrical power require ents necessary to operate
the unit satisfactorily are listed on the serial plate located on the back panel of each dryer. The
electrical connection should be ade to the ter inal board, on the rear of the unit in the upper
control box using copper conductors of 15A ini u capacity. It is absolutely necessary that the
dryer be grounded to a known (earth) ground.
The installation ust eet the National Electrical Require ents of the country of installation.
Individual 15A circuit breakers for each dryer are required. The installer ust provide a
disconnect switch which will interrupt both lines. It ay be a local or national require ent to
provide an electrical interruption switch visible and accessible fro the roo in which the dryer is
installed. The wiring diagra is located on the belt guard on the back of the dryer.
5. GAS REQUIREMENTS. The co plete gas require ents necessary to operate the dryer
satisfactorily are listed on the serial plate located on the back panel of the dryer.
The inlet gas connection to the unit is ½ in. NPT pipe thread. However, the size of the piping to
supply the dryer should be deter ined by reference to national installation practice and
consultation with the local gas supplier.
A joint co pound resistant to all fuel gases ust be e ployed in aking threaded pipe
connections.
A drip tee should be provided in the unit gas piping to catch dirt and other foreign articles.
All pipe connections should be checked for leakage with soap solution. Never check with an
open fla e.
8
CAUTION: The dryer and its individual shutoff valve ust be disconnected fro the gas supply
piping syste during any pressure testing of that syste at test pressures in excess of ½ psig
(35 bar). The dryer ust be isolated fro the gas supply piping syste by closing its individual
anual shutoff valve during any pressure testing of the gas supply piping syste at test pressures
equal to or less than ½ psig (35 bar).
6. EXHAUST INSTALLATION. (Refer to Figure 3 at the end of section 6.) Exhausting of the
dryer(s) should be planned and constructed so that no air restrictions occur. Any restriction due to
pipe size or type of installation can cause slow drying ti e, excessive heat, and lint in the roo .
Fro an operational standpoint, incorrect or inadequate exhausting can cause a cycling of the
high li it ther ostat, which shuts off the ain burners and results in inefficient drying.
Individual exhausting of the dryers is reco ended. All heat, oisture, and lint should be
exhausted outside by attaching a pipe of the proper dia eter to the dryer adapter collars and
extending it out through an outside wall. This pipe ust be very s ooth on the inside, as rough
surfaces tend to collect lint, which will eventually clog the duct and prevent the dryer fro
exhausting properly. All elbows ust be s ooth on the inside. All joints ust be ade so the
exhaust end of one pipe is inside the next one downstrea . The addition of an exhaust pipe tends
to reduce the a ount of air the blower can exhaust. This does not affect the dryer operation if
held within practical li its. For the ost efficient operation, it is reco ended that no ore than
14 ft. (4.25 ) of straight 6 in. (152 ) dia eter pipe with two right angle elbows be used for
each cylinder.
If the exhaust pipe passes through a wall, a etal sleeve of slightly larger dia eter should be set
in the wall and the exhaust pipe passed through this sleeve. This practice is required by so e
local codes and is reco ended in all cases to protect the wall.
This type of installation should have a eans provided to prevent rain and high winds fro
entering the exhaust when the dryer is not in use. A hood with a hinged da per can be used for
this purpose. Another ethod would be to point the outlet end of the pipe downward to prevent
entrance of wind and rain. In either case, the outlet should be kept clear, by at least 24 in. (610
) of any objects, which would cause air restriction.
Provide a screen or grill over the ter ination of the exhaust or flue outlet such as will prevent the
entry of a ball of 5/8 (16 ) in dia eter while the achine is not operating but will allow entry
of a ball 1/4 (6 ) in dia eter while operating.
When exhausting a dryer straight up through a roof, the overall length of the duct has the sa e
li its as exhausting through a wall. A rain cap ust be placed on top of the exhaust and ust be
of such a type as to be free fro clogging. The type using a cone shaped “roof” over the pipe is
suitable for this application.
Exhausting the dryer into a chi ney or under a building is not per itted. In either case there is a
danger of lint buildup, which can be highly co bustible.
9
Installation of several dryers, where a ain discharge duct is necessary, will need the following
considerations for installation (see Figure 3). Individual 6 in. (152 ) exhaust ducts fro the
each dryer should enter ain discharge duct at a 45-degree angle in the direction of discharge
airflow.
NOTE: Never install the individual ducts at a right angle into the ain discharge duct.
The individual ducts fro the dryers can enter at the sides or botto of the ain discharge
duct. Figure 3 indicates the various round ain duct dia eters to use with the individual
dryer ducts. The ain duct can be rectangular or round, provided adequate airflow is
aintained. The total exhausting ( ain discharge duct plus duct outlet fro the dryer)
should not exceed the equivalent of 14 ft. (4.5 ) and two elbows. The dia eter of the
ain discharge duct at the last dryer ust be aintained to exhaust end.
NOTE: A s all dia eter duct will restrict airflow; a large dia eter duct will reduce air velocity
- both contributing to lint build up. An inspection door should be provided for periodic clean out
of the ain duct.
10
7. DRYER IGNITION (SOLID STATE IGNITION). The solid-state ignition syste lights the
ain burner gas by spark. The gas is ignited and burns only when the gas-valve relay (in the
electronic controller) calls for heat. The procedure for first-ti e starting of a dryer is as follows:
A. First, review and co ply with the “WARNINGS ABOUT USE AND OPERATION” found
on the inside front cover of this anual. Be sure the electrical power supply is connected
correctly. The dryer MUST be properly grounded.
B. Make sure all gas supply lines are purged of air. Close the ain gas shut-off valve and wait
for five inutes before turning the valve back on.
C. Turn on the ain electrical power switch. The dryer ay be started by following the
“OPERATING INSTRUCTIONS” found later in this anual.
D. Natural gas and liquefied petroleu gas fired dryers both operate in the sa e anner. When
the gas-valve relay contacts are closed (indicating a de and for heat), the solid-state ignition
control will auto atically supply energy to the redundant gas valve. Spark will continue until a
fla e is detected by the sensing probe, but not longer than 10 seconds. If the gas fails to ignite
within 10 seconds, the gas will shut off for 15 seconds. The control will atte pt to ignite two
ore ti es in a si ilar anner. If the gas fails to ignite after three tries, the gas valve closes and
the syste will “lock out”. No further atte pts at ignition will be perfor ed auto atically. It is
then necessary to interrupt electrical power to the ignition syste before aking another atte pt
at igniting the burners. This can be done by opening the dryer door, allowing the dryer to co e to
a stop for 15 seconds, closing the door, and pushing the Start button. The dryer will then repeat
the ignition trial cycle.
DRYER SHUTDOWN
To render the dryer inoperative, turn off the ain gas shut-off valve and disconnect electrical
power to the dryer.
Tabla de contenidos
Otros manuales de Secadora de Dexter Laundry
Dexter Laundry
Dexter Laundry DN0170 XL Manual de usuario
Dexter Laundry
Dexter Laundry DDAD T-30 2 Series Guía del administrador
Dexter Laundry
Dexter Laundry T-30 Manual de usuario
Dexter Laundry
Dexter Laundry DL2X30Q Manual
Dexter Laundry
Dexter Laundry DDAD30HC-11 Series Manual de usuario
Dexter Laundry
Dexter Laundry DDAD30KC Series Manual de usuario
Dexter Laundry
Dexter Laundry T-20 SWD Manual de usuario
Dexter Laundry
Dexter Laundry DDAD30HC-59 Series Dryers Manual de usuario
Dexter Laundry
Dexter Laundry T-30 Guía del administrador
Dexter Laundry
Dexter Laundry STACK DRYER Manual de usuario
Dexter Laundry
Dexter Laundry C Series Manual de usuario
Dexter Laundry
Dexter Laundry DN20X2 Guía
Dexter Laundry
Dexter Laundry T-20X2 Manual de usuario
Dexter Laundry
Dexter Laundry DCT30KC Series Manual de usuario
Dexter Laundry
Dexter Laundry T-30 Manual de usuario
Dexter Laundry
Dexter Laundry V Series Manual
Dexter Laundry
Dexter Laundry DC30X2 Series Instrucciones de construcción
Dexter Laundry
Dexter Laundry T-30SWD Manual de usuario
Dexter Laundry
Dexter Laundry T-30 Manual de usuario
Dexter Laundry
Dexter Laundry T-50X2 Guía
Manuales populares de Secadora de otras marcas
Indesit
Indesit IDV 75 Manual de usuario
Infiniton
Infiniton SD-DG85C Manual de usuario
BOMANN
BOMANN WT 5019 Manual de usuario
Alliance Laundry Systems
Alliance Laundry Systems TMB795C Manual de usuario
Asko
Asko T793C Manual de usuario
Kenmore
Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer Manual de usuario