DeWalt DWFP72155 Manual de usuario

DWFP72155

15 Gauge Precision Point™ “DA” Style Angle Finish Nailer

Cloueuse De Finition D'angle « DA » Precision Point™ De Calibre 15

Clavadora De Acabado Con Ángulo Estilo "DA" Con Punta De Precisión Calibre 15

INSTRUCTION MANUAL

GUIDE D’UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE

GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE

USAR EL PRODUCTO.

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-DEWALT • www.dewalt.com

BEFORE OPERATING THIS TOOL, CAREFULLY READ AND

UNDERSTAND ALL INSTRUCTIONS IN THE IMPORTANT

SAFETY INSTRUCTIONS SECTION.

Deﬁnitions: Safety Guidelines

The definitions below describe the level of severity for each

signal word. Please read the manual and pay attention to these

symbols.

DANGER: Indicates an imminently hazardous situation

which, if not avoided, will result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which,

if not avoided, could result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which,

if not avoided, may result in minor or moderate injury.

NOTICE: Indicates a practice not related to personal injury

which, if not avoided, may result in property damage.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR

ANY D

WALT TOOL, CALL US TOLL FREE AT: 1-800-4-D

WALT

(1-800-433-9258)

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

Important Safety Instructions

WARNING: Do not operate this unit until you read this instruction

manual for safety, operation and maintenance instructions.

WARNING: This product contains chemicals known to the State

of California to cause cancer, and birth defects or other reproductive

harm. Wash hands after handling.

WARNING: Some dust contains chemicals known to the State of

California to cause cancer, birth defects or other reproductive harm such

as asbestos and lead in lead based paint.

• Actuating tool may result in flying FIG. A

FIG. B

FIG. C

FIG. D

debris, collation material, or dust

which could harm operator’s eyes.

The operator and all those persons in the

general area should wear safety glasses

with permanently attached side shields.

Approved safety glasses are imprinted

with the characters “Z87.1”. It is the

employer’s responsibility to enforce the

use of eye protection equipment by the

tool operator and other people in the work

area. (Fig. A)

• Always wear appropriate personal

hearing and other protection during

use. Under some conditions and duration

of use, noise from this product may

contribute to hearing loss. (Fig. A)

• Use only clean, dry, regulated air.

Condensation from an air compressor can

rust and damage the internal workings of

the tool. (Fig. B)

• Regulate air pressure. Use air

pressure compatible with ratings on

the nameplate of the tool. (Not to

exceed 120 psi, 8.3 bar) Do not connect

the tool to a compressor rated at over

200 psi. The tool operating pressure must

never exceed 200 psi even in the event of

regulator failure. (Fig. C)

English

• Only use air hose that is rated for a maximum working

pressure of at least 150 PSI (10.3 BAR) or 150% of the

maximum system pressure, which ever is greater. (Fig. D)

• Do not use bottled gases to power this FIG. E

FIG. F

FIG. G

tool. Bottled compressed gases such as

oxygen, carbon dioxide, nitrogen, hydrogen,

propane, acetylene or air are not for use

with pneumatic tools. Never use

combustible gases or any other reactive

gas as a power source for this tool. Danger

of explosion and/or serious personal injury

may result. (Fig. E)

• Use couplings that relieve all pressure

from the tool when it is disconnected

from the power supply. Use hose

connectors that shut off air supply from

compressor when the tool is disconnected.

(Fig. F)

• Disconnect tool from air supply when

not in use. Always disconnect tool

from air supply and remove fasteners

from magazine before leaving the

area or passing the tool to another

operator. Do not carry tool to another

work area in which changing location

involves the use of scaffoldings, stairs,

ladders, and the like, with air supply

connected. Do not make adjustments,

remove magazine, perform maintenance or clear jammed

fasteners while connected to the air supply. If the contact trip is

adjusted when the tool is connected to the air supply and nails are

loaded, accidental discharge may occur. (Fig. G)

• Connect tool to air supply before loading fasteners, to

prevent a fastener from being fired during connection. The

tool driving mechanism may cycle when tool is connected to

the air supply. Do not load fasteners with trigger or contact trip

depressed, to prevent unintentional firing of a fastener.

• Do not remove, tamper with, or FIG. H

FIG. I

FIG. J

otherwise cause the tool, trigger, or

contact trip to become inoperable.

Do not tape or tie trigger or contact trip in

the on position. Do not remove spring

from contact trip. Make daily inspections

for free movement of trigger and contact

trip. Uncontrolled discharge could result.

• Inspect tool before use. Do not

operate a tool if any portion of the tool,

trigger, or contact trip is inoperable,

disconnected, altered, or not working

properly. Leaking air, damaged parts

or missing parts should be repaired or

replaced before use. (Fig.H)

• Do not alter or modify the tool in any

way. (Fig. I)

• Always assume that the tool contains

fasteners.

• Do not point the tool at co-workers

or yourself at any time. No horseplay!

Work safe! Respect the tool as a working

implement. (Fig. J)

English

• Keep bystanders, children, and visitors away while operating

a power tool. Distractions can cause you to lose control. When

tool is not in use, it should be locked in a safe place, out of the

reach of children.

• Remove finger from trigger when

not driving fasteners. Never carry

tool with finger on trigger. Accidental

discharge could result. Using the trigger

lock-off will prevent accidental discharge.

• Do not overreach. Maintain proper

footing and balance at all times. Loss of

balance may cause cause personal injury.

(Fig. K)

• Make sure hose is free of obstructions

or snags. Entangled or snarled hoses

can cause loss of balance or footing.

• Use the tool only for its intended

use. Do not discharge fasteners into

open air, concrete, stone, extremely

hard woods, knots or any material

too hard for the fastener to penetrate.

Do not use the body of the tool or top

cap as a hammer. Discharged fasteners

may follow unexpected path and cause

injury. (Fig. L)

• Always keep fingers clear of contact

trip to prevent injury from inadvertent

release of nails. (Fig. M)

• Refer to the Maintenance and Repairs

sections for detailed information on

the proper maintenance of the tool

• Always operate the tool in a clean,

FIG. P

FIG. N

FIG. O

lighted area. Be sure the work surface

is clear of any debris and be careful not

to lose footing when working in elevated

environments such as rooftops.

• Do not drive fasteners near edge

of material. The workpiece may split

causing the fastener to ricochet, injuring

you or a co-worker. Be aware that the nail

may follow the grain of the wood (shiner),

causing it to protrude unexpectedly from

the side of the work material. Drive the

nail perpendicular to the grain to reduce

risk of injury. (Fig. N)

• Do not drive nails onto the heads

of other fasteners or with the tool

at too steep an angle. Personal injury

from strong recoil, jammed fasteners, or

ricocheted nails may result. (Fig. O)

• Be aware of material thickness when

using the nailer. A protruding nail may

cause injury.

• Be aware that when the tool is being

utilized at pressures on the high end

of its operating range, nails can be

driven completely through thin or

very soft work material. Make sure

the pressure in the compressor is set so

that nails are set into the material and not

pushed completely through. (Fig. P)

FIG. K

FIG. L

FIG. M

English

• Keep hands and body parts clear of FIG. Q

FIG. R

FIG. S

immediate work area. Hold workpiece

with clamps when necessary to keep

hands and body out of potential harm. Be

sure the workpiece is properly secured

before pressing the nailer against the

material. The contact trip may cause the

work material to shift unexpectedly.

(Fig.Q)

• Do not use tool in the presence of

flammable dust, gases or fumes. The

tool may produce a spark that could

ignite gases causing a fire. Driving a nail

into another nail may also cause a spark.

(Fig.R)

• Keep face and body parts away from

back of the tool cap when working

in restricted areas. Sudden recoil can

result in impact to the body, especially

when nailing into hard or dense material.

(Fig. S)

• Grip tool firmly to maintain control

while allowing tool to recoil away

from work surface as fastener is

driven. In “Contact Actuation Mode” if

contact trip is allowed to recontact work

surface before trigger is released an

unwanted fastener will be fired.

• Choice of triggering method is

important. Check the manual for triggering options.

BUMP/CONTACT ACTION TRIGGER

• When using the contact action

FIG. T

trigger, be careful of unintentional

double fires resulting from tool

recoil. Unwanted fasteners may be

driven if the contact trip is allowed to

accidentally re-contact the work surface.

(Fig. T)

TO AVOID DOUBLE FIRES:

• Do not engage the tool against the

work surface with a strong force.

• Allow the tool to recoil fully after each actuation.

• Use sequential action trigger.

• When “contact” actuating the nailer, always keep tool in

control. Inaccurate placement of tool can result in misdirected

discharge of a fastener.

SEQUENTIAL ACTION TRIGGER

• When using the sequential action FIG. U

trigger, do not actuate the tool

unless the tool is placed firmly

against the workpiece.

• DEPTH ADJUSTMENT: To reduce

risk of serious injury from accidental

actuation when attempting to adjust

depth, ALWAYS;

• Disconnect air supply

• Avoid contact with trigger during

adjustments

• Do not drive nails blindly into walls, floors or other work

areas. Fasteners driven into live electrical wires, plumbing, or other

types of obstructions can result in injury. (Fig.U)

English

• Stay alert, watch what you are doing and use common

sense when operating a power tool. Do not use tool while

tired or under the influence of drugs, alcohol, or medication.

A moment of inattention while operating power tools may result in

serious personal injury.

WARNING: Some dust created by power sanding, sawing,

grinding, drilling, and other construction activities contains chemicals

known to the State of California to cause cancer, birth defects or other

reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry

products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you

do this type of work. To reduce your exposure to these chemicals:

work in a well ventilated area, and work with approved safety

equipment, such as those dust masks that are specially designed to

filter out microscopic particles.

WARNING: ALWAYS USE SAFETY GLASSES. Everyday

eyeglasses are NOT safety glasses. Also use face or dust mask

if operation is dusty. ALWAYS WEAR CERTIFIED SAFETY

EQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA/Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratory protection.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

Tool Speciﬁcations

MODEL DWFP72155

DESCRIPTION 15 GA "DA" Style Angled Finish Nailer

ENGINE TYPE Oil-Free

OPERATION PRESSURE

RANGE 70–120 psi (4.9 – 8.43kg/cm2)

MAXIMUM OPERATION

PRESSURE 120 psi (8.43 kg/cm2)

AIR CONSUMPTION AT A

RATE OF 60 FASTENERS

PER MINUTE*

1.8 cfm @ 80 psi (5.6 kg/cm2)

FASTENER TYPE DA Style

FASTENER GAUGE 15 Gauge

FASTENER RANGE 1-1/4"–2-1/2" (31mm – 63mm)

MAGAZINE CAPACITY Up to 100 Nails

LENGTH 12.8" (325mm)

WIDTH 3.8" (97mm)

HEIGHT 12.1" (307mm)

WEIGHT 4.22lbs (1.9kg)

* The DWFP72155 requires 1.8 cubic feet per minute or cfm (51.0

liters per minute or lt/min) of free air at 80 PSI (5.6 kg/cm2) to operate

at a rate of 60 fasteners per minute.

To determine the appropriately sized air compressor, take the actual

rate at which the tool will be run and compare the required C.F.M.

(LT/MIN) to the compressors free air delivery (cfm/ lt/min) at 80 psi

(5.6 kg/cm2).

For example, if your fastener usage averages 30 fasteners per minute,

you need 50% of the tools cfm required to operate the tool at the

rate of 60 fasteners per minute. In this case, be sure that your air

compressor can deliver a minimum of 0.9 c.f.m. (25.5 lt/min) at 80 psi

(5.6 kg/cm2) for optimum performance of the DWFP72155.

English

COMPONENTS (FIG.1)

A. Trigger

B. Trigger mode selector

C. Jam clearing latch

D. Contact trip

E. No-mar pad

F. Magazine

G. Pusher

H. Swivel air inlet

I. Rear exhaust

J. Adjustable belt hook

K. Depth adjustment wheel

L. Pencil sharpener

FIG. 1

OPERATION

Preparing the Tool

WARNING: Read the section titled Important Safety Instructions

at the beginning of this manual. Always wear eye and ear protection

when operating this tool. Keep the nailer pointed away from yourself

and others. For safe operation, complete the following procedures

and checks before each use of the nailer.

CAUTION: NEVER spray or in any other way apply lubricants or

cleaning solvents inside the tool. This can seriously affect the life and

performance of the tool.

NOTE: These nailers are designed to be used without oil.

1. Before you use the nailer, be sure that the compressor tanks

have been properly drained.

2. Wear proper eye, hearing and respiratory protection.

3. Remove all fasteners from the magazine.

4. Check for smooth and proper operation of contact trip and

pusher assemblies. Do not use tool if either assembly is not

functioning properly. NEVER use a tool that has the contact trip

restrained in the up position.

5. Check air supply. Ensure that air pressure does not exceed

recommended operating limits, refer to Tool Specifications.

6. Connect air hose.

7. Check for audible leaks around valves and gaskets. Never use

a tool that leaks or has damaged parts.

WARNING: To reduce the risk of personal injury, disconnect tool

from air supply before performing maintenance, clearing a jammed

fastener, leaving work area, moving tool to another location or

handing the tool to another person.

English

Mode Selection

WARNING: Always wear proper eye [ANSI Z87.1 (CAN/CSA

Z94.3)] and hearing protection [ANSI S12.6 (S3.19)] when operating

this tool.

WARNING: Keep fingers AWAY from trigger when not driving

fasteners to avoid accidental firing. NEVER carry tool with finger on

trigger. In contact mode tool will fire a fastener if safety is bumped

while trigger is depressed.

Sequential Trip

Sequential trip requires the operator to hold the trigger against the

work surface before pulling the trigger. This makes accurate fastener

placement easier. The sequential trip allows exact fastener placement

without the possibility of driving a second fastener on recoil, as

described under Contact Trip. The sequential trip tool has a positive

safety advantage because it will not accidentally drive a second

fastener if the tool is contacted against the work surface or anything

else while the operator is holding the trigger pulled.

Bump/Contact Action

The common operating procedure on contact trip tools is for the

operator to contact the work surface to actuate the trip mechanism

while keeping the trigger pulled, thus driving a fastener each time the

work is contacted. This will allow rapid fastener placement on many

jobs. All pneumatic tools are subject to recoil when driving fasteners.

The tool may bounce, releasing the trip, and if unintentionally allowed

to recontact the work surface with the trigger still actuated (finger still

holding the trigger pulled) an unwanted second fastener will be driven.

TO CHANGE OPERATING MODES (FIG. 1–3)

WARNING: Disconnect air line from tool and remove fasteners

from magazine before making adjustments or personal injury may

result.

SEQUENTIAL TRIP ACTION

Use sequential action for intermittent nailing where very careful and

accurate placement is desired.

To operate the nailer in sequential action FIG. 2

mode:

1. Rotate the trigger mode selector (B)

clockwise to the sequential action position

, as shown in Figure 2.

2. Fully depress nosepiece against the work

surface.

3. Pull trigger.

4. Release trigger.

5. Lift nosepiece off work surface.

6. Repeat steps 2 through 4 for next application.

WARNING: The contact trip needs to be depressed followed by a

trigger pull for each fastener followed by a release of both the contact

trip and trigger after each fastener.

CONTACT TRIP ACTION

Bump/contact action is intended for rapid nailing on flat, stationary

surfaces.

When using bump action, two methods are available: place

actuation and bump actuation.

Rotate the trigger mode selector (B) FIG. 3

counterclockwise to the contact action position

, as shown in Figure 3.

To operate the tool using the PLACE

ACTUATION method:

WARNING: A fastener will fire each time the

trigger is depressed as long as the contact trip

remains depressed.

1. Depress the contact trip against the work surface.

English

2. Depress the trigger.

To operate the tool using the BUMP ACTUATION method:

1. Depress the trigger.

2. Push the contact trip against the work surface. As long as the

trigger is depressed, the tool will fire a fastener every time the

contact trip is depressed. This allows the user to drive multiple

fasteners in sequence.

WARNING: Do not keep trigger depressed when tool is not in use.

Keep the contact trip lock-off engaged in the locked position when

the tool is not in use.

Tool Operation Check (Fig.1)

WARNING: If the tool is dropped or you suspect tool damage

perform tool operation check.

WARNING: Remove all fasteners from tool before performing tool

operation check.

SEQUENTIAL TRIP ACTION

A. Press the contact trip against the work surface, without touching

the trigger.

THE TOOL MUST NOT CYCLE.

B. Hold the tool off the work surface and pull the trigger.

THE TOOL MUST NOT CYCLE.

C. Pull the trigger and press the contact trip against the work

surface.

THE TOOL MUST NOT CYCLE.

D. With finger off the trigger, press the contact trip against the work

surface. Pull the trigger.

THE TOOL MUST CYCLE.

CONTACT TRIP ACTION

A. With finger off the trigger, press the contact trip against the work

surface.

THE TOOL MUST NOT CYCLE.

B. Hold the tool off the work surface, and pull the trigger.

THE TOOL MUST NOT CYCLE.

C. With the tool off the work surface, pull the trigger. Press the

contact trip against the work surface.

THE TOOL MUST CYCLE.

D. Without touching the trigger, press the contact trip against the

work surface, then pull the trigger.

THE TOOL MUST CYCLE.

Loading the Tool (Fig. 4)

WARNING: Keep tool pointed in a safe direction when loading

nails.

WARNING: Never load nails with the contact trip or trigger

activated.

LOAD AND PULL PUSHER (FIG. 4)

1. Load nails through the slot in the rear of the magazine to past

retaining clip.

2. Pull pusher back behind nail stick and release.

3. Ensure magazine pusher is behind the last nail stick.

4. Blow the magazine clean periodically to keep the pusher moving

smoothly and to keep dirt and debris out of the nail channel.

FIG. 4

English

Tabla de contenidos

Idiomas:

Otros manuales de Pistola de clavos de DeWalt

DeWalt

DeWalt DCN682M1 Manual de usuario

DeWalt

DeWalt XR LI-ION DCN660N Manual de usuario

DeWalt

DeWalt DCN45RN Manual de usuario

DeWalt

DeWalt DWFP2350 Manual de usuario

DeWalt

DeWalt D51275 Manual de usuario

DeWalt

DeWalt DCN660 Manual de usuario

DeWalt

DeWalt D51822 Manual de usuario

DeWalt

DeWalt DC610 Manual de usuario

DeWalt

DeWalt D51238 Manual de usuario

DeWalt

DeWalt DCK264P2T-GB Manual de usuario

DeWalt

DeWalt DWFP12233-CA Manual de usuario

DeWalt

DeWalt DCN45RN Manual de usuario

DeWalt

DeWalt D51825 Manual de usuario

DeWalt

DeWalt DPN1850-XJ Manual de usuario

DeWalt

DeWalt DCN692 Manual de usuario

DeWalt

DeWalt DDF5110500 Manual de usuario

DeWalt

DeWalt DCN890 Manual de usuario

DeWalt

DeWalt DCN890 Manual de usuario

DeWalt

DeWalt DW325PT Manual de usuario

DeWalt

DeWalt D51823 Manual de usuario

DeWalt

DeWalt DWF83C Manual de usuario

DeWalt

DeWalt DC628-XE Manual de usuario

DeWalt

DeWalt DCN680 Manual de usuario

DeWalt

DeWalt DCN690 Manual de usuario

Manuales populares de Pistola de clavos de otras marcas

Performance Tool

Performance Tool M643 Manual de usuario

Hitachi

Hitachi VH650 - Fencing Nailer, Full Head Manual de usuario

Parkside

Parkside PET 25 B1 Manual de usuario

Senco

Senco Fusion Technology F-35XP Manual de usuario

Grizzly

Grizzly G1847 Manual de usuario

Ryobi

Ryobi R18N18G Manual de usuario

Black & Decker

Black & Decker 492848-00 Manual de usuario

HOLZMANN MASCHINEN

HOLZMANN MASCHINEN TN90 Manual de usuario

Metabo HPT

Metabo HPT NR 3690DC Manual de instrucciones

Surtek

Surtek CN650 Dimensiones y guía de instalación

Makita

Makita GF600 Manual de usuario

Parkside

Parkside PET 25 B1 Manual de usuario

Senco

Senco AirFree 25 Manual de usuario

Freeman

Freeman P50LSLW Manual de usuario

Aicon PRO

Aicon PRO DAC4507 Manual de usuario

DAJ

DAJ XR150A Manual de usuario

Makita

Makita AN923 Manual de usuario

Grizzly

Grizzly T20644 Manual de usuario