Design SHIFT ORWL Manual de usuario

ORWL User Guide Document

USER GUIDE

FOR ORWL CONFIGURATION

Version 0.4

ORWL User Guide Document

Introduction 5

Hardware Requirements 5

Configuration of ORWL 6

Step 1: Power on ORWL 6

Step 2: Display Predefined (Shipping) PIN entry message 7

Step 4: Enter User pin 8

Step 5: User PIN Verification 9

Step 6: Display hash verification message 10

Step 7: KeyFob Association 11

Step 8: Display completion of configuration status 13

ORWL User Guide Document

Revision History

Version

Date

Description of changes

Author(s)

0.1

09-May-17

Initial draft on ORWL configuration user

guide

Chaitra

0.2

13-06-17

Document modified based on the

comments provided by Daniel

Chaitra

0.3

27-Sep-17

Modification of User guide with respect to

latest OLED messages and flow of SuC

software.

Manjunath R S

0.4

11-Oct-2017

Updated the review comments provided by

Ravikiran

Manjunath R S

ORWL User Guide Document

1. Introduction

This document briefs on the steps to be followed to configure the ORWL device.

2. Hardware Requirements

The hardware equipments required are listed below:

● ORWL

● Power supply

Add an image of power supply

● HDMI cable

Add an image of HDMI cable

ORWL User Guide Document

● KeyFOB

3. Configuration of ORWL

Following are the steps to configure the ORWL device.

Step 1: Power on ORWL

Connect the Power adapter to the USB port just opposite to the Power button and switch on the

power supply. The position of button is shown in below figure.

“Welcome To ORWL message” followed by “ORWL” logo is displayed on OLED and this

message is displayed for few seconds.

ORWL User Guide Document

Step 2: Display Predefined (Shipping) PIN entry message

After timeout of ORWL logo “Please enter shipping PIN” is displayed followed by “Please press

power button to proceed.”

Follow instructions on the OLED. Once power button is pressed “PIN entry UI” is displayed. The

UI contains all the digits followed by a backspace icon. A cursor pointer(^) will indicate the digit

that is selected by the user.

Enter 6-digit predefined PIN received through mail.

Move the cursor to required digit’s position by holding the power button and release it to select

the respective digit.

User need to wait till a “*” is displayed for the next digit of PIN entry. Once the * is displayed

wait for the cursor to shift to a different position, then continue with the entering the next digit.

In case if the selected digit is wrong, then move the cursor to the Backspace icon and wait till it

clears the digit. Repeat the steps if needed to clear all the digits.

If pin verification is unsuccessful, it is indicated by a message “Verification Failed!” , followed by

“Please enter shipping PIN” further followed by “Please press power button to proceed” is

displayed. Follow the instructions OLED.

Verification failed

ORWL User Guide Document

If retry count of 3 is already tried, then a message “Wait till next PIN entry is allowed” will be

displayed.

Wait till next PIN entry is allowed

After the timeout, “Please enter shipping PIN” followed by “Please press power button to

proceed” is displayed.  Follow the instructions OLED.

If PIN verification is successful, “PIN verified” then it will continue with next step.

Step 3: Display User (custom) PIN entry message

Once Predefined PIN verification is successful, a message “Set custom PIN” followed by

“Please press power button to proceed” is displayed. Follow the instructions on OLED.

Step 4: Enter User pin

Due to security reasons User should not set PIN as “000000”. If tries to set he will be displayed

with a ne error message as show below.

“Invalid Password Please Try again”

Enter any 6-digit custom user pin to be set.

The UI contains all the digits followed by a backspace icon. A cursor pointer is also available

which shifts from digits to digits sequentially as user presses the power button. PIN digits need

to be selected by pressing the power button continuously. Once a digit is selected by moving

the cursor to that digit, stop pressing the power button for some time till the digit is written on the

UI. The UI is same as figure displayed in step 4.

ORWL User Guide Document

Once custom PIN entry is successful, a message “Re-Enter PIN” is displayed followed by

Please Press Power Button to proceed to confirm the PIN entered.

Follow instructions on OLED.

Enter the same 6-digit pin which is entered above to confirm the user pin.

If user pin configuration is successful, “Custom PIN set” message is displayed for few seconds

and flow continues with step 6.

If PIN configuration is unsuccessful, “PIN didn’t match Please retry...” message is displayed and

flow will be restarted from step 3.

Step 5: User PIN Verification

Once Custom PIN is set and in case the ORWL is restarted by user. Need to verify the User PIN

to login.

Following message “Enter your PIN” is displayed for few seconds followed by Please Press

power button to proceed.

ORWL User Guide Document

Press power button on the ORWL to continue. Enter the 6-digit custom pin which is configured

by user to verify the user. The UI is same as figure displayed in step 4.

If user pin verification is successful, “Login successful” message is displayed for few seconds

and flow will proceed with next step.

Otherwise, “Login failed” message is displayed and flow needs to started again from step 13.

Step 6: Display hash verification message

Message “VERIFY HASH Please press power button to confirm” is displayed to verify the hash

and ensure the safe shipment of ORWL to a valid user.

64 byte hash is displayed on the UI. User needs to verify the hash with the hash shared to them

via mail. If hash is correct, user needs to press the power button on the ORWL and flow

continues with next step.

Manuales populares de Portátil de otras marcas

Honeywell

Honeywell Dolphin 9900 Manual de usuario

Honeywell

Honeywell CN75 Manual de usuario

MiTAC

MiTAC Mio 168 Manual de usuario

Wasp

Wasp WDT92 Manual de usuario

Texas Instruments

Texas Instruments TI-Nspire Manual de usuario

AXEM Technology

AXEM Technology MBS Manual de usuario

Armstrong

Armstrong Brain Wave Instrucciones de montaje

Unitech

Unitech TB128 Manual de usuario

Symbol

Symbol MC9000-G Manual de instalación y operación

Unitech

Unitech HT1 1D Batch Manual de usuario

Ingenico

Ingenico IWL220 GPRS Manual de usuario

Intermec

Intermec CK61 Manual de usuario

Symbol

Symbol c2000 Manual de usuario

Symbol

Symbol MC18 Manual de instalación y operación

Acer

Acer n20 Manual de usuario

Intermec

Intermec CK61 Manual de usuario

Docomo

Docomo F-04H Manual de usuario

Toshiba

Toshiba e350 Series Manual de usuario